Doc's Dry Dock
N38W27091 PARKSIDE LN, Pewaukee, WI 53072 · Waukesha County
Establishment
- Type
- Restaurant (retail food serving meals) (Retail Food - Serving Meals)
- Inspected by
- Waukesha County Environmental Health
- License / ID
- ISPS-9JPQL4
- Status
- Permitted
- Phone
- (262) 691-9947
- Official record
- Waukesha County Environmental Health inspection reports
Year by year
| Year | Inspections | Violations | Serious |
|---|---|---|---|
| 2026 | 2 | 17 | 2 |
| 2023 | 7 | 42 | 1 |
Inspections
-
May 7, 2026 Re-inspection · 6 core, 6 repeat
-
Not serious
Core
Repeat
SINGLE-USE AND SINGLE SERVICE ARTICLES - USE LIMITATIONS
Several Country Crock plastic containers observed being reused to hold other food items in them.
Correction: Discard single-use and single service articles after initial use.
Code 4-502.13 (A)
-
Not serious
Core
Repeat
NON-FOOD CONTACT SURFACES - CLEAN
Non-food contact surfaces of the following is soiled and is in need of cleaning: -Floor under and between fryers.
Correction: Clean and remove dust, dirt, food residue, and other debris from all non-food contact surfaces of equipment.
Code 4-601.11 (C)
-
Not serious
Core
Repeat
HANDWASHING SINKS, INSTALLATION - NON-HAND OPERATED
Handwashing sink in the mens restroom is not non-hand operated as the handles are missing. Just the handle screws are present.
Correction: Employee handwashing sinks shall be non hand operated and if metered shall provide a flow of water without the need for reactivation for at least 15 seconds.
Code 5-202.12 (C)
-
Not serious
Core
Repeat
PLUMBING - SERVICE SINK
There is no service sink provided in food establishment.
Correction: Provide at least 1 service sink or curbed cleaning facility.
Code 5-203.13
-
Not serious
Core
Repeat
SURFACE CHARACTERISTICS - INDOOR AREAS
-Floor below mixer (near the basement) is chipped and is not in a smooth and easily cleanable condition. -Numerous VCT kitchen ceiling tiles are brown/dark yellow in color. Original ceiling tiles are white in color.
Correction: Repair area or replace with approved materials. Walls, floors and ceilings shall be smooth, durable and easily cleanable. If located in areas subject to moisture they shall also be non-absorbent.
Code 6-101.11
-
Not serious
Core
Repeat
INSECTS AND RODENTS - OUTER OPENINGS PROTECTED
There is a gap at the bottom of the basement delivery door, which could be the source for the entrance of insects or rodents.
Correction: Repair this hole or gap so that entrance by insects or rodents into the food establishment is prevented.
Code 6-202.15 (A) (1)
-
Not serious
Core
Repeat
-
Apr 29, 2026 Routine · 2 priority, 9 core, 3 repeat
-
Serious
Priority
TCS FOOD - COLD HOLDING
True 2-door cooler has an air temperature of 42-44°F.
Correction: Maintain cold time/temperature control for safety food at or below 41°F. Discard unsafe food items.
Code 3-501.16 (A) (2) AND (B)
-
Serious
Priority
Corrected on site
TOXIC SUBSTANCES - SANITIZER CRITERIA
-Spray bottle at the bar exceeds 200 PPM bleach. Test strip turned back to white as it bleached itself out. -Sanitizer bucket at the warewashing area exceeds 200 PPM. *Both the spray bottle and sanitizer bucket were changed out and re-set up to 100 PPM. Corrected.
Correction: Sanitizer shall meet the requirements under 40 CFR 180.940 or 40 CFR 180.2020.
Code 7-204.11
-
Not serious
Core
Repeat
PERSONAL CLEANLINESS - HAIR RESTRAINTS
A few employees noted working in food preparation/cooking area without a hair restraint.
Correction: Provide employees working in food preparation and cooking areas with effective hair restraint (hat, hair net, beard restraint, etc.).
Code 2-402.11
-
Not serious
Core
WAREWASHING - MECHANICAL HOT WATER - TEMPERATURE MEASURING DEVICES
An irreversible registering thermometer is not provided for measuring utensil surface temperatures in the hot water mechanical warewashing operation.
Correction: Provide an irreversible registering thermometer.
Code 4-302.13 (B)
-
Not serious
Core
SINGLE-USE AND SINGLE SERVICE ARTICLES - USE LIMITATIONS
Several Country Crock plastic containers observed being reused to hold other food items in them.
Correction: Discard single-use and single service articles after initial use.
Code 4-502.13 (A)
-
Not serious
Core
Repeat
NON-FOOD CONTACT SURFACES - CLEAN
Non-food contact surfaces of the following is soiled and is in need of cleaning: -Floor under and between fryers.
Correction: Clean and remove dust, dirt, food residue, and other debris from all non-food contact surfaces of equipment.
Code 4-601.11 (C)
-
Not serious
Core
HANDWASHING SINKS, INSTALLATION - NON-HAND OPERATED
Handwashing sink in the mens restroom is not non-hand operated as the handles are missing. Just the handle screws are present.
Correction: Employee handwashing sinks shall be non hand operated and if metered shall provide a flow of water without the need for reactivation for at least 15 seconds.
Code 5-202.12 (C)
-
Not serious
Core
PLUMBING - SERVICE SINK
There is no service sink provided in food establishment.
Correction: Provide at least 1 service sink or curbed cleaning facility.
Code 5-203.13
-
Not serious
Core
TOILET FACILITIES - RECEPTACLES - COVERED
Female bathroom is not provided with a covered waste receptacle.
Correction: Provide a covered waste receptacle in female bathroom for use with sanitary napkins.
Code 5-501.17
-
Not serious
Core
Repeat
SURFACE CHARACTERISTICS - INDOOR AREAS
-Floor below mixer (near the basement) is chipped and is not in a smooth and easily cleanable condition. -Numerous VCT kitchen ceiling tiles are brown/dark yellow in color. Original ceiling tiles are white in color.
Correction: Repair area or replace with approved materials. Walls, floors and ceilings shall be smooth, durable and easily cleanable. If located in areas subject to moisture they shall also be non-absorbent.
Code 6-101.11
-
Not serious
Core
INSECTS AND RODENTS - OUTER OPENINGS PROTECTED
There is a gap at the bottom of the basement delivery door, which could be the source for the entrance of insects or rodents.
Correction: Repair this hole or gap so that entrance by insects or rodents into the food establishment is prevented.
Code 6-202.15 (A) (1)
-
Serious
Priority
-
Dec 13, 2023 Re-inspection · 3 core, 3 repeat
-
Not serious
Core
Repeat
NON-FOOD CONTACT SURFACES - CLEAN
Non-food contact surfaces of the following are soiled and are in need of cleaning: -Floor below fryers has grease buildup. -Flour buildup on the floor and cart where dough mixer sits. -Sticky residue on lowest shelf on right side of bar coolers.
Correction: Clean and remove dust, dirt, food residue, and other debris from all non-food contact surfaces of equipment.
Code 4-601.11 (C)
-
Not serious
Core
Repeat
SURFACE CHARACTERISTICS - INDOOR AREAS
-Floor below dough mixer is in poor condiiton/pieces are missing. -Numerous ceiling tiles in the kitchen area are brown and are no longer easily cleanable.
Correction: Repair area or replace with approved materials. Walls, floors and ceilings shall be smooth, durable and easily cleanable. If located in areas subject to moisture they shall also be non-absorbent.
Code 6-101.11
-
Not serious
Core
Repeat
HANDWASHING SIGNAGE
No handwashing signage provided at the kitchen handwashing sink and in the men's restroom.
Correction: Provide handwashing signage at all handwashing sinks used by food employees.
Code 6-301.14
-
Not serious
Core
Repeat
-
Nov 29, 2023 Re-inspection 2 · 2 priority foundation, 3 core, 5 repeat
-
Not serious
Priority Foundation
Repeat
WAREWASHING MACHINE - HIGH TEMPERATURE - WASH SOLUTION TEMPERATURE
The temperature of the wash solution of the high temperature dishmachine is less than 150 F (124 F). The rinse temperature of the dish machine is less than 180 F (170-172 F). Highest temperature reached was 172 F after several cycles.
Correction: Maintain the wash temperature in the high temperature warewashing machine at a temperature indicated in 4-501.110 (A) or indicated by the manufacturer.
Code 4-501.110 (A)
-
Not serious
Priority Foundation
Repeat
FOOD CONTACT SURFACES - MECHANICAL WAREWASHING EQUIPMENT, HOT WATER SANITIZATION TEMPERATURES
Water temperature for the sanitization rinse (At plate temperature) in the Hobart high temperature warewashing machine is at 155.4° F at plate (2 cycles ran). Temperature in the dish machine noted to drop after each cycle. Person-in-charge noted that there has been a leak in the back of the unit but has not called it in for repairs. The at plate temperature shall be at least 160 F. The dish machine can be used to wash and rinse but cannot be used to sanitize. All dishes and utensils shall be sanitized at the three compartment sink. Manager stated that Hobart has looked at the dishmachine but is unsure when repairs will be made as it is up to the owner. The manager wants to use the dishmachine for sanitizing as it is quicker. Bleach at the compartment sink shall be used in the range of 50-200 PPM.
Correction: Adjust the water temperature so the hot water is between [ °F] and 194 °F or have the unit serviced immediately. Food establishment shall cease operations unless alternative warewashing is available. [Describe].
Code 4-501.112
-
Not serious
Core
Repeat
NON-FOOD CONTACT SURFACES - CLEAN
Non-food contact surfaces of the following are soiled and are in need of cleaning: -Floor below fryers has grease buildup. -Flour buildup on the floor and cart where dough mixer sits. -Sticky residue on lowest shelf on right side of bar coolers.
Correction: Clean and remove dust, dirt, food residue, and other debris from all non-food contact surfaces of equipment.
Code 4-601.11 (C)
-
Not serious
Core
Repeat
SURFACE CHARACTERISTICS - INDOOR AREAS
-Floor below dough mixer is in poor condiiton/pieces are missing. -Numerous ceiling tiles in the kitchen area are brown and are no longer easily cleanable.
Correction: Repair area or replace with approved materials. Walls, floors and ceilings shall be smooth, durable and easily cleanable. If located in areas subject to moisture they shall also be non-absorbent.
Code 6-101.11
-
Not serious
Core
Repeat
HANDWASHING SIGNAGE
No handwashing signage provided at the kitchen handwashing sink and in the men's restroom.
Correction: Provide handwashing signage at all handwashing sinks used by food employees.
Code 6-301.14
-
Not serious
Priority Foundation
Repeat
-
Nov 16, 2023 Re-inspection · 3 priority foundation, 3 core, 6 repeat
-
Not serious
Priority Foundation
Repeat
WAREWASHING MACHINE - HIGH TEMPERATURE - WASH SOLUTION TEMPERATURE
The temperature of the wash solution of the high temperature dishmachine is less than 150 F (124 F). The rinse temperature of the dish machine is less than 180 F (170-172 F). Highest temperature reached was 172 F after several cycles.
Correction: Maintain the wash temperature in the high temperature warewashing machine at a temperature indicated in 4-501.110 (A) or indicated by the manufacturer.
Code 4-501.110 (A)
-
Not serious
Priority Foundation
Repeat
FOOD CONTACT SURFACES - MECHANICAL WAREWASHING EQUIPMENT, HOT WATER SANITIZATION TEMPERATURES
Water temperature for the sanitization rinse (At plate temperature) in the Hobart high temperature warewashing machine is at 155.4° F at plate (2 cycles ran). Temperature in the dish machine noted to drop after each cycle. Person-in-charge noted that there has been a leak in the back of the unit but has not called it in for repairs. The at plate temperature shall be at least 160 F. The dish machine can be used to wash and rinse but cannot be used to sanitize. All dishes and utensils shall be sanitized at the three compartment sink. Manager stated that Hobart has looked at the dishmachine but is unsure when repairs will be made as it is up to the owner. The manager wants to use the dishmachine for sanitizing as it is quicker. Bleach at the compartment sink shall be used in the range of 50-200 PPM.
Correction: Adjust the water temperature so the hot water is between [ °F] and 194 °F or have the unit serviced immediately. Food establishment shall cease operations unless alternative warewashing is available. [Describe].
Code 4-501.112
-
Not serious
Priority Foundation
Repeat
FOOD CONTACT SURFACES - SOILED
Right-hand soda gun at the bar has slime buildup in the holder.
Correction: Maintain food contact surfaces in a clean condition.
Code 4-601.11 (A)
-
Not serious
Core
Repeat
NON-FOOD CONTACT SURFACES - CLEAN
Non-food contact surfaces of the following are soiled and are in need of cleaning: -Floor below fryers has grease buildup. -Flour buildup on the floor and cart where dough mixer sits. -Sticky residue on lowest shelf on right side of bar coolers.
Correction: Clean and remove dust, dirt, food residue, and other debris from all non-food contact surfaces of equipment.
Code 4-601.11 (C)
-
Not serious
Core
Repeat
SURFACE CHARACTERISTICS - INDOOR AREAS
-Floor below dough mixer is in poor condiiton/pieces are missing. -Numerous ceiling tiles in the kitchen area are brown and are no longer easily cleanable.
Correction: Repair area or replace with approved materials. Walls, floors and ceilings shall be smooth, durable and easily cleanable. If located in areas subject to moisture they shall also be non-absorbent.
Code 6-101.11
-
Not serious
Core
Repeat
HANDWASHING SIGNAGE
No handwashing signage provided at the kitchen handwashing sink and in the men's restroom.
Correction: Provide handwashing signage at all handwashing sinks used by food employees.
Code 6-301.14
-
Not serious
Priority Foundation
Repeat
-
Nov 9, 2023 Re-inspection 2 · 3 priority foundation, 3 core, 6 repeat
-
Not serious
Priority Foundation
Repeat
WAREWASHING MACHINE - HIGH TEMPERATURE - WASH SOLUTION TEMPERATURE
The temperature of the wash solution of the high temperature dishmachine is less than 150 F (124 F). The rinse temperature of the dish machine is less than 180 F (170-172 F). Highest temperature reached was 172 F after several cycles.
Correction: Maintain the wash temperature in the high temperature warewashing machine at a temperature indicated in 4-501.110 (A) or indicated by the manufacturer.
Code 4-501.110 (A)
-
Not serious
Priority Foundation
Repeat
FOOD CONTACT SURFACES - MECHANICAL WAREWASHING EQUIPMENT, HOT WATER SANITIZATION TEMPERATURES
Water temperature for the sanitization rinse (At plate temperature) in the Hobart high temperature warewashing machine is at 155.4° F at plate (2 cycles ran). Temperature in the dish machine noted to drop after each cycle. Person-in-charge noted that there has been a leak in the back of the unit but has not called it in for repairs. The at plate temperature shall be at least 160 F. The dish machine can be used to wash and rinse but cannot be used to sanitize. All dishes and utensils shall be sanitized at the three compartment sink. Manager stated that Hobart has looked at the dishmachine but is unsure when repairs will be made as it is up to the owner. The manager wants to use the dishmachine for sanitizing as it is quicker. Bleach at the compartment sink shall be used in the range of 50-200 PPM.
Correction: Adjust the water temperature so the hot water is between [ °F] and 194 °F or have the unit serviced immediately. Food establishment shall cease operations unless alternative warewashing is available. [Describe].
Code 4-501.112
-
Not serious
Priority Foundation
Repeat
FOOD CONTACT SURFACES - SOILED
Right-hand soda gun at the bar has slime buildup in the holder.
Correction: Maintain food contact surfaces in a clean condition.
Code 4-601.11 (A)
-
Not serious
Core
Repeat
NON-FOOD CONTACT SURFACES - CLEAN
Non-food contact surfaces of the following are soiled and are in need of cleaning: -Floor below fryers has grease buildup. -Flour buildup on the floor and cart where dough mixer sits. -Sticky residue on lowest shelf on right side of bar coolers.
Correction: Clean and remove dust, dirt, food residue, and other debris from all non-food contact surfaces of equipment.
Code 4-601.11 (C)
-
Not serious
Core
Repeat
SURFACE CHARACTERISTICS - INDOOR AREAS
-Floor below dough mixer is in poor condiiton/pieces are missing. -Numerous ceiling tiles in the kitchen area are brown and are no longer easily cleanable.
Correction: Repair area or replace with approved materials. Walls, floors and ceilings shall be smooth, durable and easily cleanable. If located in areas subject to moisture they shall also be non-absorbent.
Code 6-101.11
-
Not serious
Core
Repeat
HANDWASHING SIGNAGE
No handwashing signage provided at the kitchen handwashing sink and in the men's restroom.
Correction: Provide handwashing signage at all handwashing sinks used by food employees.
Code 6-301.14
-
Not serious
Priority Foundation
Repeat
-
Nov 1, 2023 Re-inspection 2 · 3 priority foundation, 3 core, 6 repeat
-
Not serious
Priority Foundation
Repeat
WAREWASHING MACHINE - HIGH TEMPERATURE - WASH SOLUTION TEMPERATURE
The temperature of the wash solution of the high temperature dishmachine is less than 150 F (Started at 151 F, then dropped to 147.5 F.) The rinse temperature of the dish machine is less than 180 F. Highest temperature reached was 172 F after several cycles.
Correction: Maintain the wash temperature in the high temperature warewashing machine at a temperature indicated in 4-501.110 (A) or indicated by the manufacturer.
Code 4-501.110 (A)
-
Not serious
Priority Foundation
Repeat
FOOD CONTACT SURFACES - MECHANICAL WAREWASHING EQUIPMENT, HOT WATER SANITIZATION TEMPERATURES
Water temperature for the sanitization rinse (At plate temperature) in the Hobart high temperature warewashing machine is at 147.5-151° F at plate (3 cycles ran). Temperature in the dish machine noted to drop after each cycle. Person-in-charge noted that there has been a leak in the back of the unit but has not called it in for repairs. The at plate temperature shall be at least 160 F. The dish machine can be used to wash and rinse but cannot be used to sanitize. All dishes and utensils shall be sanitized at the three compartment sink. Bleach water was set-up at 50 PPM. Bleach shall be used in the range of 50-200 PPM.
Correction: Adjust the water temperature so the hot water is between [ °F] and 194 °F or have the unit serviced immediately. Food establishment shall cease operations unless alternative warewashing is available. [Describe].
Code 4-501.112
-
Not serious
Priority Foundation
Repeat
FOOD CONTACT SURFACES - SOILED
Right-hand soda gun at the bar has slime buildup in the holder.
Correction: Maintain food contact surfaces in a clean condition.
Code 4-601.11 (A)
-
Not serious
Core
Repeat
NON-FOOD CONTACT SURFACES - CLEAN
Non-food contact surfaces of the following are soiled and are in need of cleaning: -Floor below fryers has grease buildup. -Flour buildup on the floor and cart where dough mixer sits. -Sticky residue on lowest shelf on right side of bar coolers.
Correction: Clean and remove dust, dirt, food residue, and other debris from all non-food contact surfaces of equipment.
Code 4-601.11 (C)
-
Not serious
Core
Repeat
SURFACE CHARACTERISTICS - INDOOR AREAS
-Floor below dough mixer is in poor condiiton/pieces are missing. -Numerous ceiling tiles in the kitchen area are brown and are no longer easily cleanable.
Correction: Repair area or replace with approved materials. Walls, floors and ceilings shall be smooth, durable and easily cleanable. If located in areas subject to moisture they shall also be non-absorbent.
Code 6-101.11
-
Not serious
Core
Repeat
HANDWASHING SIGNAGE
No handwashing signage provided at the kitchen handwashing sink and in the men's restroom.
Correction: Provide handwashing signage at all handwashing sinks used by food employees.
Code 6-301.14
-
Not serious
Priority Foundation
Repeat
-
Oct 25, 2023 Re-inspection · 3 priority foundation, 3 core, 6 repeat
-
Not serious
Priority Foundation
Repeat
WAREWASHING MACHINE - HIGH TEMPERATURE - WASH SOLUTION TEMPERATURE
The temperature of the wash solution of the high temperature dishmachine is less than 150 F (Started at 151 F, then dropped to 147.5 F.) The rinse temperature of the dish machine is less than 180 F. Highest temperature reached was 172 F after several cycles.
Correction: Maintain the wash temperature in the high temperature warewashing machine at a temperature indicated in 4-501.110 (A) or indicated by the manufacturer.
Code 4-501.110 (A)
-
Not serious
Priority Foundation
Repeat
FOOD CONTACT SURFACES - MECHANICAL WAREWASHING EQUIPMENT, HOT WATER SANITIZATION TEMPERATURES
Water temperature for the sanitization rinse (At plate temperature) in the Hobart high temperature warewashing machine is at 147.5-151° F at plate (3 cycles ran). Temperature in the dish machine noted to drop after each cycle. Person-in-charge noted that there has been a leak in the back of the unit but has not called it in for repairs. The at plate temperature shall be at least 160 F. The dish machine can be used to wash and rinse but cannot be used to sanitize. All dishes and utensils shall be sanitized at the three compartment sink. Bleach water was set-up at 50 PPM. Bleach shall be used in the range of 50-200 PPM.
Correction: Adjust the water temperature so the hot water is between [ °F] and 194 °F or have the unit serviced immediately. Food establishment shall cease operations unless alternative warewashing is available. [Describe].
Code 4-501.112
-
Not serious
Priority Foundation
Repeat
FOOD CONTACT SURFACES - SOILED
Right-hand soda gun at the bar has slime buildup in the holder.
Correction: Maintain food contact surfaces in a clean condition.
Code 4-601.11 (A)
-
Not serious
Core
Repeat
NON-FOOD CONTACT SURFACES - CLEAN
Non-food contact surfaces of the following are soiled and are in need of cleaning: -Floor below fryers has grease buildup. -Flour buildup on the floor and cart where dough mixer sits. -Sticky residue on lowest shelf on right side of bar coolers.
Correction: Clean and remove dust, dirt, food residue, and other debris from all non-food contact surfaces of equipment.
Code 4-601.11 (C)
-
Not serious
Core
Repeat
SURFACE CHARACTERISTICS - INDOOR AREAS
-Floor below dough mixer is in poor condiiton/pieces are missing. -Numerous ceiling tiles in the kitchen area are brown and are no longer easily cleanable.
Correction: Repair area or replace with approved materials. Walls, floors and ceilings shall be smooth, durable and easily cleanable. If located in areas subject to moisture they shall also be non-absorbent.
Code 6-101.11
-
Not serious
Core
Repeat
HANDWASHING SIGNAGE
No handwashing signage provided at the kitchen handwashing sink and in the men's restroom.
Correction: Provide handwashing signage at all handwashing sinks used by food employees.
Code 6-301.14
-
Not serious
Priority Foundation
Repeat
-
Oct 18, 2023 Routine · 1 priority, 3 priority foundation, 6 core, 4 repeat
-
Serious
Priority
Repeat
Corrected on site
FOOD CONTACT SURFACES - WAREWASHING EQUIPMENT, CHEMICAL, TEMPERATURE, pH, CONCENTRATION AND HARDNESS
The bleach sanitizer in the spray bottle at the bar is not being used according to EPA registered label use instructions and exceeds 200 PPM. Sanitizer bottle contents were discarded of and was re-set up. Bleach sanitizer tested to 50 PPM. Corrected.
Correction: Provide training to employees on proper use and concentration of sanitizer or repair or adjust warewashing equipment to provide proper sanitizer concentration.
Code 4-501.114 (A) - (E)
-
Not serious
Priority Foundation
WAREWASHING MACHINE - HIGH TEMPERATURE - WASH SOLUTION TEMPERATURE
The temperature of the wash solution of the high temperature dishmachine is less than 150 F. The rinse temperature of the dish machine is less than 180 F.
Correction: Maintain the wash temperature in the high temperature warewashing machine at a temperature indicated in 4-501.110 (A) or indicated by the manufacturer.
Code 4-501.110 (A)
-
Not serious
Priority Foundation
FOOD CONTACT SURFACES - MECHANICAL WAREWASHING EQUIPMENT, HOT WATER SANITIZATION TEMPERATURES
Water temperature for the sanitization rinse in the Hobart high temperature warewashing machine is at 130-150° F at plate. Temperature in the dish machine noted to drop after each cycle. Person-in-charge noted that there has been a leak in the back of the unit but has not called it in for repairs. The at plate temperature shall be at least 160 F. The dish machine can be used to wash and rinse but cannot be used to sanitize. All dishes and utensils shall be sanitized at the three compartment sink. Bleach water was set-up at 50 PPM. Bleach shall be used in the range of 50-200 PPM.
Correction: Adjust the water temperature so the hot water is between [ °F] and 194 °F or have the unit serviced immediately. Food establishment shall cease operations unless alternative warewashing is available. [Describe].
Code 4-501.112
-
Not serious
Priority Foundation
Repeat
FOOD CONTACT SURFACES - SOILED
Right-hand soda gun at the bar has slime buildup in both the nozzle and holder.
Correction: Maintain food contact surfaces in a clean condition.
Code 4-601.11 (A)
-
Not serious
Core
EATING, DRINKING, OR USING TOBACCO
Employee was observed drinking from a cup in the kitchen area.
Correction: Provide employee break room or designate an area away from food preparation for eating and tobacco use.
Code 2-401.11 (A)
-
Not serious
Core
Repeat
OPEN DRINK CONTAINER
Drinking cup without cover was observed in food preparation area.
Correction: Provide approved beverage container with cover in food preparation area.
Code 2-401.11 (B)
-
Not serious
Core
PERSONAL CLEANLINESS - HAIR RESTRAINTS
A few employees noted working in food preparation/cooking area without a hair restraint.
Correction: Provide employees working in food preparation and cooking areas with effective hair restraint (hat, hair net, beard restraint, etc.).
Code 2-402.11
-
Not serious
Core
NON-FOOD CONTACT SURFACES - CLEAN
Non-food contact surfaces of the following are soiled and are in need of cleaning: -Floor below fryers has grease buildup. -Flour buildup on the floor and cart where dough mixer sits. -Sticky residue on lowest shelf on right side of bar coolers.
Correction: Clean and remove dust, dirt, food residue, and other debris from all non-food contact surfaces of equipment.
Code 4-601.11 (C)
-
Not serious
Core
Repeat
SURFACE CHARACTERISTICS - INDOOR AREAS
-Floor below dough mixer is in poor condiiton/pieces are missing. -Numerous ceiling tiles in the kitchen area are brown and are no longer easily cleanable.
Correction: Repair area or replace with approved materials. Walls, floors and ceilings shall be smooth, durable and easily cleanable. If located in areas subject to moisture they shall also be non-absorbent.
Code 6-101.11
-
Not serious
Core
HANDWASHING SIGNAGE
No handwashing signage provided at the kitchen handwashing sink and in the men's restroom.
Correction: Provide handwashing signage at all handwashing sinks used by food employees.
Code 6-301.14
-
Serious
Priority
Repeat
Corrected on site
Source: Waukesha County Environmental Health. History last read Nov 21, 2026. Violation text is the inspector's wording. “Serious” is the source's own top tier. About this data.