RecordWell Data

Public Works Committee Meeting january 2023

City of Mauldin · Greenville County · meeting of Dec 30, 2022 · Notices

Open the original document More from City of Mauldin

Text

Extracted automatically from the original. Tables and formatting may not survive; the original document is authoritative.

PUBLIC WORKS COMMITTEE MEETING TUESD AY, JANUARY 3, 2023 | 6 PM 4th committee meeting The Committee will meet in Mauldin City Hall at 5 East Butler Road in the Council Chambers at 6 p.m. The meeting will be available remotely through Zoom. Please visit the City’s website at https://cityofmauldin.org/your-government/meeting-minutes-agendas/ to access the meeting via audio and videoconferencing. A quorum of Council will be present. 1 PUBLIC WORKS COMMITTEE MEETING JANUARY 3, 2023, 6PM CITY HALL - COUNCIL CHAMBERS 5 E. BUTLER ROAD Committee Members: Jason Kraeling (Chair), Carol King, Michael Reynolds 1. Call to Order 2. Public Comment 3. Reading and Approval of Minutes a.Public Works Committee Meeting: December 5, 2022 [Pages 3-4] 4. Reports or Communications from City Officers a.Public Works Director Matt Fleahman Budget Review GLDTC Participation Agreement [Pages 5-12] 5. Unf inished Business There is no unfinished business. 6. New Business a.Park Restroom Facilities Upgrade [Pages 13-29] 7. Pub lic Comment 8. Committee Concerns 9. Adjournment The Honorable Jason Kraeling The Hono rable Jason Kraeling The Hono rable Jason Kraeling Th e Honorable Jason Kraeling The H onorable Jason Kraeling The Honorable Jason Kraeling Th e Honorable Jason Kraeling Th e Honorable Jason Kraeling Th e Honorable Jason Kraeling 2 PUBLIC WORKS COMMITTEE MEETING DECEMBER 5, 2022, 6PM CITY HALL - COUNCIL CHAMBERS 5 E. BUTLER ROAD 3rd committee meeting Committee Members present: Jason Kraeling (Chair), Carol King, Michael Reynolds Others present: PW Director Matthew Fleahman and City Administrator Seth Duncan 1. Call to Order- Chairman Kraeling 2. Public Comment- None 3. Reading and Approval of Minutes a. Public Works Committee Meeting: November 7, 2022 Motion: Councilman Reynolds made a motion to accept the minutes with Councilwoman King seconding. Vote: The vote was unanimous (3-0). 4. Reports or Communications from City Officers a. Public Works Director Matt Fleahman Budget Review Mr. Fleahman reported to committee that all of his divisions are under budget. Revised plans for the East Butler Road project were received today. The concrete medians in front of the fire station and sports center have been removed. 5. Unfinished Business- There is no unfinished business. 6. New Business a. Maverick Yards Maintenance Agreement This item is a maintenance agreement between both parties which stipulates that the City will be primarily responsible for performing maintenance on both the parking lot and the landscaped areas. In it, the City agrees to at a minimum reseal and restripe the parking lot every 5 years and to repave every 20 years. The maintenance schedule for the landscaped areas has already been implemented by the Public Works Department. The potential cost to repave is approximately 150,000 dollars while resurfacing costs are approximately 10,000 dollars. Councilwoman King asked if the 5-year re-sealing is standard. Mr. Fleahman said it is a little excessive, but we want it to look as nice as possible. Councilwoman King said if in five years it doesn’t need to be done, we are committed to doing it. Mr. Fleahman said there is a provision in the agreement that says it will be done as long as the funds are available. 3 Motion: Councilwoman King made a motion to send this agreement to Council with Councilman Reynolds seconding. Vote: The vote was unanimous (3-0). 7. Public Comment-None 8. Committee Concerns- Chairman Kraeling asked about the City Christmas decorations. Mr. Fleahman said power is not on all the poles, so some of the decorations are not lit. A quote to repair all the poles was $100,000. Mr. Fleahman said the decorations are very heavy and several of them fall when it is windy outside and are damaged. Councilwoman King said the goal setting session is next month and can be discussed then. Eventually they are going to have to be replaced. When the East Butler Road project is done, all of the light poles will be replaced. 9. Adjournment- Chairman Kraeling adjourned the meeting at 6:44 p.m. Respectfully Submitted, Cindy Miller Municipal Clerk 4 PUBLIC WORKS COMMITTEE AGENDA ITEM MEETING DATE: January 3, 2023 AGENDA ITEM: 2a TO: Public Works Committee FROM: Public Works Director, Matthew Fleahman SUBJECT: GLDTC Participation Agreement REQUEST Information only, to let the Public Works Committee and City Council know that the C-Fund Collaboration request from July 20, 2020 for the redesign of the Standing Springs Road and Ashmore Bridge road interchange in cooperation with the County of Greenville SC will be executed aft er the Committee Meetings. HISTORY/BACKGROUND The City of Mauldin worked to attain access and annexation of the former Bonnie Brae Golf Course along Ashmore Bridge Road. The site was annexed into the City with plans to develop a 700- 800 lot housing subdivision. During the annexation process, concerns from the public were presented regarding increased traffic, and the alignment of Standing Springs Road onto Ashmore Bridge. Mark III Properties the developer for the subdivision. Via their attached correspond ence, Mark III Properties is partnered with Greenville County and the SCDOT in a multi-jurisdictional project to improve the intersection of Ashmore Bridge Road and Standing Springs Road. City Council approved a funding allocation of $50,000 contingent on the funding by the C -Funds Committee during its July 2020 Council Meeting. ANALYSIS or STAFF FINDINGS City Staff were contacted on December 19, 2022 and informed that C -funds had been allocated to the redesign and signaling of the intersection. A participation agreement and invoice for the $50,000 were provided for GLTDC Project 579. FINANCIAL IMPACT The cost associated with modification will not exceed $50,000.00. RECOMMENDATION No recommendation is provided as this is for information only. 5 CITY COUNCIL AGENDA ITEM MEETING DATE: July 20, 2020 AGENDA ITEM: 8c TO: City Council FROM: Community D evelopment Director Van Broad SUBJECT: C- Fund collaboration Re quest / v ia Greenville County REQUEST Council is requested to a request from Mark III Properties to assist in funding the redesign of Standing Springs Road and Ashmore Bridge Road interchange in cooperation with the County of Greenville SC. HISTORY/BACKGROUND The City of Mauldin worked to attain access and annexation of the former Bonnie Brae Golf Course along Ashmore Bridge Road. The site was annexed into the City with plans to develop a 700-800 lot housing subdivision. During the annexation process, concerns from the public were presented regarding increased traffic, and the alignment of Standing Springs Road onto Ashmore Bridge. Mark III Properties the developer for the subdivision. Via their attached correspondence, Mark III Properties is partnered with Greenville County and the SCDOT in a multi-jurisdictional project to improve the intersection of Ashmore Bridge Road and Standing Springs Road. ANALYSIS / STAFF FINDINGS While the Ashmore Bridge Rd. and Standing Springs Rd. intersection is not a Mauldin intersection, it will be used by City residents. The proposed interchange has historically received a failing grade. Multiple new development projects will increase stress and pressure on the interchange. As proposed by Mark III Properties, this approach will repair the intersection in a manner to serve the existing traffic and projected future growth. Also, it is worth noting the SCDOT plans to install a traffic signal at the newly aligned intersection outside of the scope of the realignment project. 6 TIMELINE/FINANCIAL 1. The project will commence upon approval of funding by the C-Funds Committee 2. The total amount being requested of the City is $50,000 3. Should Council proceed, an appropriate funding source would be fund balance. RECOMMENDATION It is the recommendation of staff that council approve funding of $50,000 t oward the Standing Springs/Ashmore Bridge Re-alignment Project. ATTACHMENTS Letter from Mark III Properties Project Cost Estimate as prepared by CoTransCo 7 City of Mauldin Mr. David Dyrhaug 5 E. Butler Road Mauldin, SC 29662 June 8, 2020 Mr. Dyrhaug, Mark III Properties is teaming with Greenville County and the SCDOT in a multi-jurisdictional project to improve the intersection of Ashmore Bridge Road and Standing Springs Road. I have attached the proposed layout. This intersection has historically received a failing grade and is being made worse with the increased traffic in this area. It is time to fix the intersection in a manner to serve the existing traffic and projected future growth. The intersection is not a City of Mauldin road, however many Mauldin residents will use it every day. With the recent annexation of the Bonnie Brae golf course property (approx. 800 homes), Camden Cottages (68 homes) and Meadow Springs (151 homes), I estimate an increase in Mauldin’s tax base of over $230 million from these developments over the next few years. All of these new homes will benefit from an improved intersection at this location. Hesha Gamble with Greenville County is planning to present this project to the CTC as soon as possible. She feels the best chance of having it approved is to have participation from as many stakeholders as possible. I am writing to request the City of Mauldin commit to invest $50,000 towards this intersection improvement project. For your reference, Mark III Properties has purchased right of way ($25,000), is donating additional right-of-way ($20,000) and is planning to contribute an additional $100,000 for this intersection. We will also be doing extensive upgrades to Ashmore Bridge Road and Fork Shoals Road at the Bonnie Brae property. I understand Greenville County is working on a new / revised cost estimate, however the latest information I have shows the cost of this project to be about $1.2 million plus the right-of-way acquisition (which Mark III is contributing to the project). I’ve included the cost estimate. Also, note the SCDOT plans to install a traffic signal at the newly aligned intersection outside of the scope of the realignment project. Feel free to contact me or Joe Waldron with Mark III Properties with any questions. Sincerely, Jay Beeson 8 GLDTC 566 ASHMORE BRG / STANDING SPRINGS COST ESTIMATE ASHMORE BRIDGE RD ADDITIONAL STANDING SPRINGS TURN LANE @ RELOCATION STANDING SPRINGS WEST ITEM DESCRIPTION UNIT UNIT BID PRICE AMOUNT AMOUNT TOTAL QUANTITIES TOTAL $ MOBILIZATION LS $35,000.00 1 35,000.00$ 0 -$ 1.00 $35,000.00 CONSTR. STAKES LINES & GRADES LS $10,000.00 1 10,000.00$ 0.2 2,000. 00$ 1.20 $12,000.00 QUALITY CONTROL BY CONTRACTOR LS $15,000.00 1 15,000.00$ 0.2 3,000. 00$ 1.20 $18,000.00 TRAFFIC CONTROL LS $35,000.00 1 35,000.00$ 0.2 7,000. 00$ 1.20 $42,000.00 AS-BUILT CONSTRUCTION PLANS LS $3,000.00 1 3,000.00$ 0.2 600.00$ 1.20 $3,600.00 CLEARING & GRUBBING W/I ROADWAY LS $75,000.00 1 75,000.00$ 0.2 15,000. 00$ 1.20 $90,000.00 REM. & DISP. OF EXISTING CATCH BASIN EA $700.00 0 $0.00 0 $0.00 0.00 $0.00 REM. & DISP. OF EXISTING DROP INLET EA $650.00 0 $0.00 0 $0.00 0.00 $0.00 REM. & DISP. OF EXISTING PAVEMENT SY $15.00 0 $0.00 0 $0.00 0.00 $0.00 REM. & DISP. OF EXISTING ASPH. PAVEMENT SY $15.00 1500 $22,500.00 0 $0.00 1,500.00 $22,500.00 MILLING EXISTING ASPH. ROADWAY SY $1.65 0 $0.00 0 $0.00 0.00 $0.00 MILLING VARIABLE WIDTH 4" SY $7.50 0 $0.00 0 $0.00 0.00 $0.00 SITE EXCAVATION LS $200,000.00 1 $200,000.00 0.2 $40,000.00 1.20 $240,000.00 BORROW EXCAV. CY $18.00 0 $0.00 0 $0.00 0.00 $0.00 EXCAVATION FOR SHOULDER PAVING STA $0.00 0 $0.00 0 $0.00 0.00 $0.00 FINE GRADING SY $2.90 4500 $13,050.00 0 $0.00 4,500.00 $13,050.00 FLOWABLE FILL CY $95.00 0 $0.00 0 $0.00 0.00 $0.00 MAINTENANCE STONE TON $35.00 200 $7,000.00 0 $0.00 200.00 $7,000.00 HOT MIX ASPH. AGGR. BASE CR. TYPEC @ 650#/SY TON $50.00 1379 $68,950.00 550 $27,500.00 1,929.00 $96,450.00 LIQUID ASPH. BINDER PG 64-22 TON $650.00 163.92 $106,548.00 55.8 $36,270.00 219.72 $142,818.00 FULL DEPTH ASPHALT PVMT. PATCH-6" UNIFORM SY $33.00 0 $0.00 0 $0.00 0.00 $0.00 H/L ASPH. CONCRETE INTERMEDIATE CR. TYPE C @220TON $52.50 466.2 $24,475.50 190 $9,975.00 656.20 $34,450.50 H/L ASPH CONC SURF. COURSE TYPE C @ 220#/SY TON $52.50 866.8 $45,507.00 190 $9,975.00 1,056.80 $55,482.00 PERMANENT CONSTRUCTION SIGNS SF $12.50 300 $3,750.00 0 $0.00 300.00 $3,750.00 4" WH. BRK. LINE-GAPS EXC. FD PAINT LF $0.20 240 $48.00 0 $0.00 240.00 $48.00 4" WH. SLD. LINE-PVT. EDGE FD PAINT LF $0.20 5000 $1,000.00 520 $104.00 5,520.00 $1,104.00 8" WH. SOLID LINES (CRSS WLK & CHANN) FD PNT. LF $1.00 320 $320.00 0 $0.00 320.00 $320.00 24" WH. SOLID LINES F.D. PAINT LF $2.50 84 $210.00 24 $60.00 108.00 $270.00 4" YELLOW BRKN LINE GAPS EXC. FD PAINT LF $0.52 0 $0.00 0 $0.00 0.00 $0.00 4" YELLOW SLD. LINE- CENTER LINE FD PAINT LF $0.52 3500 $1,820.00 1040 $540.80 4,540.00 $2,360.80 WHITE SINGLE ARROWS - PAINT LF $55.00 8 $440.00 2 $110.00 10.00 $550.00 WHITE COMBO ARROWS - PAINT LF $55.00 1 $55.00 0 $0.00 1.00 $55.00 4" WH. BRK. LINE-GAPS EXC. THERMO 90 MIL LF $0.67 240 $160.80 0 $0.00 240.00 $160.80 4" WH. SLD. LINE-PVT. EDGE THERMO- 90 MIL LF $0.67 5000 $3,350.00 520 $348.40 5,520.00 $3,698.40 8" WH.SLD LINE (CRSS WLK & CHANN)THERMO125MIL LF $2.25 320 $720.00 0 $0.00 320.00 $720.00 24" WH. SOLID LINES THERMO- 125 MIL LF $10.00 84 $840.00 24 $240.00 108.00 $1,080.00 WHITE SINGLE ARROWS - THERMO 125 MIL EA $100.00 8 $800.00 2 $200.00 10.00 $1,000.00 WHITE COMBO. ARROWS - THERMO 125 MIL EA $150.00 1 $150.00 0 $0.00 1.00 $150.00 WH. WORD MESS."ONLY",-THER0-125MIL EA $150.00 4 $600.00 1 $150.00 5.00 $750.00 WH. WORD MESS."STOP",-THER0-125MIL EA $150.00 0 $0.00 0 $0.00 0.00 $0.00 WH. WORD MESS."AHEAD",-THER0-125MIL EA $150.00 0 $0.00 0 $0.00 0.00 $0.00 WH. WORD R/R SYMBOL,-THER0-125MIL EA $150.00 0 $0.00 0 $0.00 0.00 $0.00 4" YELLOW BRKN LINE GAPS EXC.THERMO 90 MIL LF $0.67 0 $0.00 0 $0.00 0.00 $0.00 4" YELLOW SLD. LINE- CENTER LINE THERMO-90 MIL LF $0.67 3500 $2,345.00 0 $0.00 3,500.00 $2,345.00 PERM. CLEAR PAVMT. MARKERS MONO-DIR EA $10.00 10 $100.00 0 $0.00 10.00 $100.00 PERM. YELLOW PAVMT. MARKERS MONO-DIR EA $10.00 0 $0.00 0 $0.00 0.00 $0.00 PERM. YELLOW PAVMT. MARKERS BI-DIRECTIONAL EA $10.00 50 $500.00 0 $0.00 50.00 $500.00 18" RC PIPE CUL. - CLASS III LF $55.00 64 $3,520.00 0 $0.00 64.00 $3,520.00 24" RC PIPE CUL. - CLASS III LF $65.00 64 $4,160.00 0 $0.00 64.00 $4,160.00 30" RC PIPE CUL. - CLASS III LF $60.00 0 $0.00 0 $0.00 0.00 $0.00 36" RC PIPE CUL. - CLASS III LF $75.00 0 $0.00 0 $0.00 0.00 $0.00 48" RC PIPE CUL. - CLASS III LF $85.00 0 $0.00 0 $0.00 0.00 $0.00 60" RC PIPE CUL. - CLASS III LF $100.00 48 $4,800.00 0 $0.00 48.00 $4,800.00 12" NON-REINFORCED BRICK MASONRY WALL CY $1,250.00 0 $0.00 0 $0.00 0.00 $0.00 12" REINFORCED BRICK MASONRY WALL CY $1,600.00 0 $0.00 0 $0.00 0.00 $0.00 CONCRETE STEPS CY $1,000.00 0 $0.00 0 $0.00 0.00 $0.00 ALUMINUM HANDRAIL LF $100.00 0 $0.00 0 $0.00 0.00 $0.00 CATCH BASIN TYPE 9 W/ MANHOLE EA $1,500.00 0 $0.00 0 $0.00 0.00 $0.00 CATCH BASIN TYPE16 EA $2,800.00 0 $0.00 0 $0.00 0.00 $0.00 24" x 36" DROP INLET EA $1,800.00 0 $0.00 0 $0.00 0.00 $0.00 MANHOLE EA $2,300.00 0 $0.00 0 $0.00 0.00 $0.00 CONCRETE CURB & GUTTER (1'-6") LF $12.00 0 $0.00 0 $0.00 0.00 $0.00 CONCRETE CURB & GUTTER (2'-0") LF $15.50 0 $0.00 0 $0.00 0.00 $0.00 PEDESTRIAN RAMP CONSTRUCTION SY $150.00 0 $0.00 0 $0.00 0.00 $0.00 CONC. SIDEWALK 5'- 0" (4"UNIFORM) SY $32.00 0 $0.00 0 $0.00 0.00 $0.00 DETECTABLE WARNING SURFACES SF $75.00 0 $0.00 0 $0.00 0.00 $0.00 CONCRETE DRIVEWAY(6" UNIFORM) SY $36.00 0 $0.00 0 $0.00 0.00 $0.00 AGGREGATE UNDERDRAIN (AGG. # 57) CY $25.00 0 $0.00 0 $0.00 0.00 $0.00 6" PERFORATED PIPE UNDERDRAIN LF $6.50 100 $650.00 0 $0.00 100.00 $650.00 RIP RAP (CLASS B) TON $40.00 100 $4,000.00 0 $0.00 100.00 $4,000.00 GTEX FOR EROS CNTRL UND RIPRAP(CLASS1)TYPE C SY $2.00 200 $400.00 0 $0.00 200.00 $400.00 STEEL BEAM GUARDRAIL LF $20.00 600 $12,000.00 0 $0.00 600.00 $12,000.00 END TERMINAL TYPE - T EA $3,000.00 2 $6,000.00 0 $0.00 2.00 $6,000.00 ADDITIONAL LENGTH GUARDRAIL POST LF $0.00 0 $0.00 0 $0.00 0.00 $0.00 48" CHAIN LINK FENCE LF $20.00 0 $0.00 0 $0.00 0.00 $0.00 RESET FENCE LF $15.00 0 $0.00 0 $0.00 0.00 $0.00 RESET CHAIN LINK FENCE LF $17.50 0 $0.00 0 $0.00 0.00 $0.00 PERMANENT VEGETATION MSY $1,000.00 6.333 $6,333.00 0.8 $800.00 7.133 $7,133.00 TEMPORARY VEGETATION MSY $750.00 3.667 $2,750.25 0.4 $300.00 4.07 $3,050.25 BALED STRAW BALE $0.00 0 $0.00 520 $0.00 520.00 $0.00 SILT FENCE LF $8.00 5000 $40,000.00 0 $0.00 5,000.00 $40,000.00 SILT BASIN CY $15.00 0 $0.00 0 $0.00 0.00 $0.00 DITCH CHECK TON $30.00 0 $0.00 0 $0.00 0.00 $0.00 SELF-ADHERING PAVING STRIP MEMBRANE CEO. SY $22.50 $0.00 0 $0.00 0.00 $0.00 CONCRETE FOR STRUCTURES (ROADWAY) CLASS 400 CY $1,200.00 0 $0.00 0 $0.00 0.00 $0.00 DIAMOND SOCK FILTERS (T-16 CB) LF $20.00 0 $0.00 0 $0.00 0.00 $0.00 DEMOLITION ITEM #1 LS $800.00 0 $0.00 0 $0.00 0.00 $0.00 DEMOLITION ITEM #2 LS $500.00 0 $0.00 0 $0.00 0.00 $0.00 DEMOLITION ITEM #3 LS $950.00 0 $0.00 0 $0.00 0.00 $0.00 4" WHITE PARKING LINES-PAINT LF $1.30 0 $0.00 0 $0.00 0.00 $0.00 6" YELLOW LINES- PAINT LF $0.40 0 $0.00 0 $0.00 0.00 $0.00 4" BLUE HANDICAP LINES- PAINT LF $3.00 0 $0.00 0 $0.00 0.00 $0.00 SPEED BUMPS EA $1,000.00 0 $0.00 0 $0.00 0.00 $0.00 0 PAVEMENT MARKINGS LS $2,000.00 0 $0.00 0 $0.00 0.00 $0.00 NEW ROADWAY SIGNAGE LS $2,000.00 0 $0.00 0 $0.00 0.00 $0.00 ESTIMATED CONSTRUCTION COST $762,852.55 $154,173.20 $917,025.75 UTILITIES - (POLES) EA $25,000.00 0 $0.00 0 $0.00 0.00 $0.00 10% CONTINGENCY $76,285.26 $15,417.32 $91,702.58 PE $83,913.78 $16,959.05 $100,872.83 CEI $83,913.78 $16,959.05 $100,872.83 ESTIMATED GRAND TOTAL $1,006,965.37 $203,508.62 $1,210,473.99 CUMMALITIVE TOTAL $1,210,473.99 NOTES: 1) WIDENING ALL ON ONE SIDE DUE TO UTILITY POLE RELOCATIONS NEEDED ON NORTH SIDE OF ROAD (6 POLES) 2. RIGHT-OF-WAY WILL BE REQUIRED FROM TWO PROPRTY OWNER IN ADDITION TO THE GOLF COURSE PROPERTY. 3.STANDING SPRINGS WEST TURN LANE ADDED IN ANTICIPATION OF SCDOT REQUIRMENTS. 4. SCDOT TO PROVIDE INSTALLATION OF THE SIGNAL AND ALL CROSSWALKS. 9 PARTICIPATION AGREEMENT Greenville Legislative Delegation Transportation Committee Project No. 579 Ashmore Bridge Rd., Mauldin, SC December 19, 2022 WHEREAS, The City of Mauldin desires the Greenville Legislative Delegation Transportation Committee (GLDTC) to assist the City of Mauldin in the design and construction of road improvements known as GLDTC Project No. 579, being described fully on C-FUND ASSISTANCE APPLICATION, 10/14/2019, that was presented to the GLDTC at the 07/28/2022 meeting, approved 09/22/2022. WHEREAS, Matt Fleahman is the Public Works Director for the City of Mauldin and duly authorized by the City of Mauldin 5 E. Butler Rd, PO Box 249 Mauldin, SC 29662 (864) 289-8904 with the authority to enter into contracts necessary for the proper discharge of its functions and duties; and WHEREAS, the City of Mauldin is duly authorized to enter into contracts necessary for the proper discharge of its functions and duties; and WHEREAS, GLDTC has agreed to assist the City of Mauldin with GLDTC Project No. 579; GLDTC will construct intersection improvements according to SCDOT Standard Specifications on Ashmore Bridge Rd.at Standing Springs Rd. NOW THEREFORE, in consideration of the several promises to be faithfully performed by the parties hereto as set forth, the GLDTC and the City of Mauldin do hereby agree as follows: Project Description: The project is divided into three (3) parts as follows: a) Design: Includes all preliminary engineering, location approval, right-of-way and construction plans, and any and all other associated tasks necessary to prepare acceptable plans ; b) Right-of-way: Includes all right-of-way acquisition services performed in accordance with Federal and SCDOT guidelines, rules, regulations, policies and procedures relative to the acquisition of right-of-way; c) Construction: Includes bidding and letting of a construction contract, the actual construction performance, construction engineering, construction inspection, sampling testing of materials, and other associated tasks as necessary. The term PROJECT is intended to refer to the above three Parts collectively unless otherwise indicated. FUNDING: GLDTC: $ 1,709,000.00 + 2/3 Overruns Mark III Properties $ 174,142.00 + 1/3 Overruns Hidden Lakes Preserve $ 24,403.05 Standing Springs Land Development, LLC $ 23,844.20 (Sunny Hill) City of Mauldin $ 50,000.00 SCDOT Provide Signalization to intersection 10 The GLDTC shall: a) Provide the GLDTC’s cost share for the PROJECT, not to exceed the $1,709,000.00; b) Provide right-of-way acquisition cost estimates for each impacted tract of land as shown on approved plans for the project; c) Provide right-of-way acquisition services to secure the necessary right-of-way as shown on approved plans for the project; d) Provide bid advertisement, awarding of construction contract, inspection of contractor work during execution of contract, and sampling and testing of construction procedures for compliance with all State and local requirements; e) Verify all contractors pay requests prior to payment. City of Mauldin a) Provide $50,000 at signing of participation agreement; b) Provide right-of-way as requested by prior agreement with the SCDOT. The GLDTC shall: a) Enter into and execute all necessary contracts necessary to complete the approved project; b) Be responsible for approval of payment requests and payment of all contractor an d s ubcontractor pay requests; c) Secure from the City of Mauldin funding as noted above prior to construction bidding. This document may not be modified or revoked without the written consent of both parties. ____ __________________________________________________________________ For: the City of Mauldin (date) ____ __________________________________________________________________ Greenville Legislative Delegation Transportation Committee Chairman (date) 11 December 19, 2022 1 579 Amount $1,709,000.00 $50,000.00 $50,000.00 Total Due $50,000.00 Greenville Legislative Delegation Transportation Committee Date: 301 University Ridge, Suite 2400 Invoice #: Greenville, SC 29601 GLDTC Project #: In accordance with the participation agreement for GLDTC 579- Ashmore Bridge Road, the amount due at this time is calculated below: City of Mauldin Attn: Matt Fleahman, Public Works Director via email: mfleahman@mauldincitysc.com phone: 864-467-7112 To: Description Total due by City of Mauldin Project Funding GLDTC: City of Mauldin Due upon receipt Payment Terms Invoice Greenville Legislative Delegation Transportation Committee Invoice Greenville Legislative Delegation Transportation Committee 12 PUBLIC WORKS COMMITTEE AGENDA ITEM M EETING DATE: January 3, 2023 AG ENDA ITEM: 6a TO : Public Works Committee FROM: Public Works Director, Matthew Fleahman SUBJECT: Park Restroom Facilities Upgrade REQUEST Authorization is requested to allocate capital funding to cover the expense of modifying the bathroom doors City Park, Sunset Park, and Springfield Park. HISTORY/BACKGROUND The Public Works Department maintains bathroom structures at three City Parks. Du e to continued vandalism and their use as a sleeping space for vagrants, the structures are required to be locked each evening and opened each morning when the park opens. Park operating hours do not coincide with the hours of operation for the Public Wor ks Department so the City’s Police force has been assisting in locking/unlocking the bathrooms. Due to the irregularity in calls for service, the Police have not been able to lock/unlock the bathrooms on a fixed schedule. ANALYSIS or STAFF FINDINGS The City has an electronic lock system on the bathrooms at the City Center restroom which locks/unlocks the doors on a timer. Public Works staff reached out the City’s on- call electrical contractor and inquired about installing this system on its other facilities. The electricians recommended Southeastern Dock & Door as a more appropriate party to conduct the install. Southeastern has been contracted before to repair garage doors at the PW facility and were the contractor that renovated the lobby at City Hall. FINCANCIAL IMPACT The cost associated with modification will not exceed $19,283.00. RECOMMENDATION Staff recommends the Public Works Committee and the City Council approve the allocation of 19,283.00 dollars from the Capital budget to cover renovations to the City’s restroom facilities. 13 1 1/29/22, 3:53 PM 141.81.180.22:8082/sm/smcontrolpanel.SMProposalPrintAction 141.81.180.22:8082/sm/smcontrolpanel.SMProposalPrintAction 1/4 Southeastern Dock and Door 54 Bruce Rd. Greenville, SC 29605 Phone: 864-277-8877 Contact: Matt Kunzweiler Email: matt.kunzweiler@assaabloy.com Direct dial: 864-979-7797 PROPOSAL ID 27743 Quote ID: 45190 Estimate Summary ID: (None) Sales Lead ID: (None) (This proposal ID 27743 printed: 11/29/2022 3:53:06 PM) Bill to: City of Mauldin P.O. Box 249 Mauldin, SC 29662 Ship-to: Access Control for City Parks Restrooms 29662 Contact: Jason Hamby Contact: Phone: 864 991 1066 Phone: DESCRIPTION: The Lump Sum Price for All of the Openings is Listed Below The restrooms below will have individual hand-programmable timers to lock the doors at the desired time. Once the restroom doors have locked, it will require a key to over-ride the maglocks and enter the restroom. In the event the restrooms lockdown while occupied a RTE motion and timed RTE pneumatic button will be installed inside to allow for free egress at all times. The over-ride keys for all park restrooms will be keyed- alike. City Park Restrooms - (2) Out-Swinging Doors Price including listed materials, installation labor, and sales tax.....................................$3,995.00 2 (ea) Alarm Controls, 1200S 12/24VDC Magnetic Lock w/1200lbs Holding Force 2 (ea) Alarm Controls, AM6330 1/4" Spacer Plate for the 1200S Maglock 2 (ea) Bosch, DS160 Request T o Exit Motion Sensor, Light Gray 2 (ea) Camden, CM-5085RPTE 2-3/8" Pushbutton, DPST Pneumatic Timer, Red 1 (ea) AC, MCK-4-4 MCK Series Mortise Cylinder Key Switch Station, DPDT , Single-Gang 1 (ea) HGR 3902-118-26D-SC1 Mortise Cylinder-KA 1 (ea) Camden, CX-247-24 Programmable 7-Day Timer, 24V AC/DC 1 (ea) Altronix, AL175ULX 12/24VDC 1.75A Power Supply w/Fire Disconnect 1 (ea) Altronix, LC2 Standard 6' 3-Wire Power Cord 2 (ea) Y uasa, NP712 12VDC 7AH SLA Battery 1 (ea) Required Hardware, Connectors and Fasteners 1 (ea) Required Low Voltage Maglock Power Wire We propose to furnish and install the maglock system as listed above. The Altronix power supply, Camden timer and key over-ride will be located in the upper call box area on the second floor and the low voltage wiring will be run down in EMT conduit as required to the restrooms. A maglock, RTE Motion, and RTE Pneumatic button will be installed in each restroom. All low voltage wiring from the ceiling to the associated device will be in EMT conduit stub-ups as required. We will assist with programming the new timer and provide additional instruction as needed on the use of the timer. The system will be tested for proper operation. Springfield Park Upper Restrooms - (1) In-Swing Door + (1) Out-Swing Door Continued on page 2. 14 1 1/29/22, 3:53 PM 141.81.180.22:8082/sm/smcontrolpanel.SMProposalPrintAction 141.81.180.22:8082/sm/smcontrolpanel.SMProposalPrintAction 2/4 Price including listed materials, installation labor, and sales tax.....................................$3,731.00 2 (ea) Alarm Controls, 1200S 12/24VDC Magnetic Lock w/1200lbs Holding Force 2 (ea) Alarm Controls, AM6330 1/4" Spacer Plate for the 1200S Maglock 1 (ea) Alarm Controls, AM6370 Z Bracket for 1200S Maglock 2 (ea) Bosch, DS160 Request T o Exit Motion Sensor, Light Gray 2 (ea) Camden, CM-5085RPTE 2-3/8" Pushbutton, DPST Pneumatic Timer, Red 1 (ea) AC, MCK-4-4 MCK Series Mortise Cylinder Key Switch Station, DPDT , Single-Gang 1 (ea) HGR 3902-118-26D-SC1 Mortise Cylinder-KA 1 (ea) Camden, CX-247-24 Programmable 7-Day Timer, 24V AC/DC 1 (ea) Altronix, AL175ULX 12/24VDC 1.75A Power Supply w/Fire Disconnect 1 (ea) Altronix, LC2 Standard 6' 3-Wire Power Cord 2 (ea) Y uasa, NP712 12VDC 7AH SLA Battery 1 (ea) Required Hardware, Connectors and Fasteners 1 (ea) Required Low Voltage Maglock Power Wire We propose to furnish and install the maglock system as listed above. The Altronix power supply, Camden timer and key over-ride will be located in the electrical room next to Men's restroom. A maglock, RTE Motion, and RTE Pneumatic button will be installed in each restroom. All low voltage wiring will be routed above the ceiling and EMT conduit stub-ups will be installed from the ceiling to the associated device. We will assist with programming the new timer and provide additional instruction as needed on the use of the timer. The system will be tested for proper operation. Lower Restrooms - (2) In-Swinging Doors Price including listed materials, installation labor, and sales tax.....................................$3,851.00 2 (ea) Alarm Controls, 1200S 12/24VDC Magnetic Lock w/1200lbs Holding Force 2 (ea) Alarm Controls, AM6330 1/4" Spacer Plate for the 1200S Maglock 2 (ea) Alarm Controls, AM6370 Z Bracket for 1200S Maglock 2 (ea) Bosch, DS160 Request T o Exit Motion Sensor, Light Gray 2 (ea) Camden, CM-5085RPTE 2-3/8" Pushbutton, DPST Pneumatic Timer, Red 1 (ea) AC, MCK-4-4 MCK Series Mortise Cylinder Key Switch Station, DPDT , Single-Gang 1 (ea) HGR 3902-118-26D-SC1 Mortise Cylinder-KA 1 (ea) Camden, CX-247-24 Programmable 7-Day Timer, 24V AC/DC 1 (ea) Altronix, AL175ULX 12/24VDC 1.75A Power Supply w/Fire Disconnect 1 (ea) Altronix, LC2 Standard 6' 3-Wire Power Cord 2 (ea) Y uasa, NP712 12VDC 7AH SLA Battery 1 (ea) Required Hardware, Connectors and Fasteners 1 (ea) Required Low Voltage Maglock Power Wire We propose to furnish and install the maglock system as listed above. The Altronix power supply, Camden timer and key over-ride will be located in the electrical room to the left of the Men's bathroom. A maglock, RTE Motion, and RTE Pneumatic button will be installed in each restroom. All low voltage wiring will be routed above the ceiling and EMT conduit stub-ups will be installed from the ceiling to the associated device. We will assist with programming the new timer and provide additional instruction as needed on the use of the timer. The system will be tested for proper operation. City Center Park Price including listed materials, installation labor, and sales tax.....................................$244.00 This location has existing maglocks on the Men's/Women's restrooms. 1 (ea) AC, MCK-4-4 MCK Series Mortise Cylinder Key Switch Station, DPDT , Single-Gang 1 (ea) HGR 3902-118-26D-SC1 Mortise Cylinder-KA Continued on page 3. 15 1 1/29/22, 3:53 PM 141.81.180.22:8082/sm/smcontrolpanel.SMProposalPrintAction 141.81.180.22:8082/sm/smcontrolpanel.SMProposalPrintAction 3/4 We propose to change out the key cylinder in one of the existing key-switches and to re-wire to a single key- switch to drop power to both maglocks when activated. The additional key-switch will be removed from the system. We will assist with programming the new timer and provide additional instruction as needed on the use of the timer. The system will be tested for proper operation. Sunset Park Restrooms @ Circular Drive - (2) Out-Swinging Doors Price including listed materials, installation labor, and sales tax.....................................$3,611.00 Important Note: New Hollow Metal doors are needed for both the Men's & Women's restrooms before the maglocks are installed. 2 (ea) Alarm Controls, 1200S 12/24VDC Magnetic Lock w/1200lbs Holding Force 2 (ea) Alarm Controls, AM6330 1/4" Spacer Plate for the 1200S Maglock 2 (ea) Bosch, DS160 Request T o Exit Motion Sensor, Light Gray 2 (ea) Camden, CM-5085RPTE 2-3/8" Pushbutton, DPST Pneumatic Timer, Red 1 (ea) AC, MCK-4-4 MCK Series Mortise Cylinder Key Switch Station, DPDT , Single-Gang 1 (ea) HGR 3902-118-26D-SC1 Mortise Cylinder-KA 1 (ea) Camden, CX-247-24 Programmable 7-Day Timer, 24V AC/DC 1 (ea) Altronix, AL175ULX 12/24VDC 1.75A Power Supply w/Fire Disconnect 1 (ea) Altronix, LC2 Standard 6' 3-Wire Power Cord 2 (ea) Y uasa, NP712 12VDC 7AH SLA Battery 1 (ea) Required Hardware, Connectors and Fasteners 1 (ea) Required Low Voltage Maglock Power Wire We propose to furnish and install the maglock system as listed above. The Altronix power supply, Camden timer and key over-ride will be located in the room to the right of the Women's bathroom. A maglock, RTE Motion, and RTE Pneumatic button will be installed in each restroom. All low voltage wiring will be routed above the ceiling and EMT conduit stub-ups will be installed from the ceiling to the associated device. We will assist with programming the new timer and provide additional instruction as needed on the use of the timer. The system will be tested for proper operation. Restrooms @ Concession Stand - (2) In-Swinging Doors Price including listed materials, installation labor, and sales tax.....................................$3,851.00 2 (ea) Alarm Controls, 1200S 12/24VDC Magnetic Lock w/1200lbs Holding Force 2 (ea) Alarm Controls, AM6330 1/4" Spacer Plate for the 1200S Maglock 2 (ea) Alarm Controls, AM6370 Z Bracket for 1200S Maglock 2 (ea) Bosch, DS160 Request T o Exit Motion Sensor, Light Gray 2 (ea) Camden, CM-5085RPTE 2-3/8" Pushbutton, DPST Pneumatic Timer, Red 1 (ea) AC, MCK-4-4 MCK Series Mortise Cylinder Key Switch Station, DPDT , Single-Gang 1 (ea) HGR 3902-118-26D-SC1 Mortise Cylinder-KA 1 (ea) Camden, CX-247-24 Programmable 7-Day Timer, 24V AC/DC 1 (ea) Altronix, AL175ULX 12/24VDC 1.75A Power Supply w/Fire Disconnect 1 (ea) Altronix, LC2 Standard 6' 3-Wire Power Cord 2 (ea) Y uasa, NP712 12VDC 7AH SLA Battery 1 (ea) Required Hardware, Connectors and Fasteners 1 (ea) Required Low Voltage Maglock Power Wire We propose to furnish and install the maglock system as listed above. The Altronix power supply, Camden timer and key over-ride will be located in the concession room located on the left side of the building facing the restrooms.A maglock, RTE Motion, and RTE Pneumatic button will be installed in each restroom. All low voltage wiring will be routed above the ceiling and EMT conduit stub-ups will be installed from the ceiling to Continued on page 4. 16 1 1/29/22, 3:53 PM 141.81.180.22:8082/sm/smcontrolpanel.SMProposalPrintAction 141.81.180.22:8082/sm/smcontrolpanel.SMProposalPrintAction 4/4 the associated device. We will assist with programming the new timer and provide additional instruction as needed on the use of the timer. The system will be tested for proper operation. To Be Provided By Others: Permanent use of a 120VAC receptacle or a 120VAC circuit at each Altronix power supply listed above. These items will need to be provided by a licensed electrician of your choosing if not available. We hereby propose to complete in accordance with above specification, for the sum of: Nineteen Thousand Two Hundred Eighty-Three Dollars And Zero Cents $19,283.00 TERMS AND CONDITIONS: Payment terms to be as follows: Net 30 Prices subject to change if not accepted in: 30 days. Net 30 Signature: Date: 11/29/2022 Matt Kunzweiler, Email: matt.kunzweiler@assaabloy.com Direct Dial: 864-979-7797 ACCEPTANCE: T erms, price, and specifications on all pages of this proposal are hereby accepted and the work authorized. Purchaser: __________________________________ Title: __________________________________ Signature: __________________________________ Date of acceptance: ________ Purchaser's PO number if required for invoicing: _________________ . (This proposal ID 27743 printed: 11/29/2022 3:53:06 PM) 17 ALARM CONTROLS www.alarmcontrols.com | 800.645.5538 © 2021, Hanchett Entry Systems, Inc., an ASSA ABLOY Group company. | Patent pending and/or patent www.assaabloydss.com/patent 7 Features Standard Features • 1200S Standard mag netic lock • 1200L Magnetic lock with indicating LED • 1200L B Magnetic lock with indicating LED, bond sensor and door status sensor • Built -in arc suppression • Inst ant release, no hysteresis • Self -drilling TEC screws • Non- aluminum parts are plated to resist corrosion • E-Z mo unt header bracket and template provided for easy installation, no special tools required • Can be u sed with any access control system • Clea r anodized (US28) finish standard • Limit ed lifetime warranty Options • DURO Duranodic finish (US 40 ) available, specify when ordering. • Dres s covers in polished chrome and brass available. See "Magnetic Lock Accessories" for options. Specifications Certifications & Listings • UL 294 listed • UL 10C fi re rated • CAN/ ULC-S104 fire door conformant • ULC- S527 listed • UL 864 l isted Holding Force • 1200 lbs Dimensions • Magnet size: 10-1/2" L x 2-7 /8" H x 1-1/2" W • Arma ture size: 7-1/4" L x 2-3/8" H x 5/8" W Electrical • 12 or 24 VDC, field sele ctable • Curr ent draw: 505 mA at 12 VDC, 260 mA at 24 VDC • 1200 LB bond sensor has SPDT 3A relay contacts Operating Temperature • +14 to +131F [-10 to +55C] Bracket mounted magnetic lock with 1200 lbs of holding force that can be easily installed without special tools and used with any access control system. Ideal for high-use areas for traffic control in interior or exterior applications. Available with LED, bond sensor and door status signalling options. 1200S, 1200L, 1200LB Single Magnetic Lock 18 16 www.alarmcontrols.com | 800.645.5538 © 2021, Hanchett Entry Systems, Inc., an ASSA ABLOY Group company. | Patent pending and/or patent www.assaabloydss.com/patent ALARM CONTROLS Magnetic LockAccessories L Brackets Fixed Single and Double Lock Brackets; Adjustable Single Lock Mounting Brackets Z Brackets Decorative Z Bracket with Integrated Dress Cover PART NUMBER DESCRIPTION DIMENSIONS FINISH Fixed Single Lock Brackets: AM3320 1/4" L bracket for 600 Series locks 9-7/8"L x 1" x 1-1/2" Clear anodized (US28) AM3320C L bracket for 600 Series single magnetic locks with cover Clear anodized (US28) AM6320 5/16" L bracket for 1200 Series locks with cover 10-1/2"L x 1-1/2" x 1" Clear anodized (US28) AM6320C L bracket for 1200 Series single magnetic locks with cover Clear anodized (US28) Adjustable Single Lock Brackets: AM3325 3/16" adjustable L bracket for 600 Series locks 9-7/8"L x 1-7/8" x 1-3/16" Clear anodized (US28) AM6325 1/4" adjustable L bracket for 1200 Series locks 10-1/2"L x 2-5/16" x 2-5/16" Clear anodized (US28) Fixed Double Lock Brackets: AM3326 5/16" L bracket for 600D and 600DLB Series double locks 19-3/4"L x 1-1/2" x 1" Clear anodized (US28) AM6326 1/4 L bracket for 1200D Series double locks 21"L x 1" x 1-1/2" Clear anodized (US28) PART NUMBER DESCRIPTION FINISH Z Bracket for 600 Series Single Magnetic Locks AM3370 Z bracket for 600 Series single magnetic locks Clear anodized (US28) • Fixed single lock L brackets for 600 or 1200 lbs magnetic locks; Option to include cover. • Adjustable single lock L bracket for 600 or 1200 lbs magnetic locks • Fixed double lock L bracket for 600 and 1200 double magnetic locks • For Duranodic finish US40 (Dark Bronze), please contact the factory • Adjustable mounting bracket for 600 or 1200 lbs Series Single Magnetic Locks • For use on in-swinging doors • AM3370C for magnetic lock models: 600S, 600L and 600LB − Adjustment range: 2" - 2.75" − Bracket dimensions: 10"L x 3.5"H • AM6370C for magnetic lock models: 1200S, 1200L and 1200LB − Adjustment range: 2.375" - 3.5" − Bracket dimensions: 10.625"L x 4.25"H • For Duranodic finish US40 (Dark Bronze), please contact the factory 19 Intrusion Alarm Systems | DS160 Series High Performance Request‑to‑exit Detectors DS160 Series High Performance Request‑to‑exit Detectors www.boschsecurity.com u Door monitor with sounder alert u Sequential Logic Input (SLI) u Internal vertical pointability u Wrap-around coverage pattern with precise pattern control u Up to 64 second adjustable latch time The DS160 Series consists of the DS160 Detector (light gray) and the DS161 Detector (black) specifically designed for Request-to-exit (REX) applications. With features such as timers, door monitor with sounder alert, and pointable coverage, the DS160 and DS161 have the flexibility to meet the most stringent REX requirements. The exclusive Sequential Logic Input (SLI) provides added security that is not offered in any other REX device. Functions Sequential Logic Input (SLI) The SLI terminal allows connection of a second device to require sequential detection. This eliminates the possibility that an object that is slid through the door or underneath the door will activate the detector. This input can also be used to lock the sensor if motion is present outside the premises. Door Monitor The sensor can monitor a door contact to allow special control of the internal relay. For example, if the door is opened within the relay time period, the sensor can be programmed to halt the timer. If the door is not opened within a specific time period, the relay can be programmed to deactivate. Sounder Alert An integrated sounder can be programmed to activate if the door is left open too long. The sounder volume is fully adjustable to 85 dB. Keycard Input The keycard input allows the sensor relay to be controlled from an external source, such as an access control system or card reader. Certifications and approvals Europe Complies with EN50131‑1 Grade 2 Region Certification Australia RCM [DS160] Europe CE 2004/108/EC EMC Directive; 2006/95/EC Low-Voltage Directive; 2011/65/EU Restriction of the use of certain hazardous substances in electri- cal and electronic equipment USA UL ALVY: Access Control Systems Units (UL294) 20 Installation/configuration notes ALARM WILL SOUND WHEN DOOR IS OPENED 3 m (10 ft) ALARM WILL SOUND WHEN DOOR IS OPENED 1.2 m (4 ft) Front View Mounted on wall above door and mounted on ceiling . 75 m (2.5 ft) in front of the door. 1.5 m (5 ft) 3 m (10 ft) Side View The higher that you mount the unit, the larger the coverage area. Do not mount the DS160/DS161 more than 4.6 m (15 ft) above the floor. Side view of coverage pattern with the unit mounted at 4.6 m (15 ft) above the floor with the lens pointed straight down. .75 m (2.5 ft) 1.5 m (5 ft) Side View The higher that you mount the unit, the larger the coverage area. Do not mount the DS160/DS161 more than 4.6 m (15 ft) above the floor. Side view of coverage pattern with the unit mounted at 4.6 m (15 ft) above the floor with the lens pointed straight down. Coverage Information The coverage (detection area) varies depending on the mounting height above the floor, angle of the lens, and whether the unit is mounted on a wall above the door or on the ceiling. The coverage is 2.4 m x 3 m (8 ft x 10 ft) The coverage patterns for the detector at a height of 2.3 m (7.5 ft) are shown. The coverage pattern increases or decreases with height and detector alignment. Notice When you mount the unit on the wall and the lens points straight down, some detection zones point toward the wall and do not detect movement. The diagrams depict views of the coverage pattern with the detector mounted at 2.3 m (7.5 ft) above the floor with the lens pointed straight down. Zones that are pointed toward the wall are not shown. Technical specifications Environmental Operating Temperature: -29°C to +49°C (-20°F to +120°F) For UL Certificated installations, 0°C to +49°C (+32°F to +120°F) Radio Frequency Interference (RFI) Immunity: No alarm or setup on critical frequencies in the range from 26 MHz to 1000 MHz at 50 V/m Complies with Environmental Class II (EN50130-5) Mechanical Dimensions: 4.5 cm x 17.1cm x 4.4 cm (1.80 in. x 6.75 in. x 1.75 in.) Material: High impact ABS plastic enclosure Modes Power Loss Default: Programmable fail-safe or fail-secure modes. Timer: Programmable reset accumulative or non-reset counting mode. Electrical Current Draw: 8 mA nominal standby current, 39 mA at 12 VDC in alarm Voltage: 12 VAC or VDC to 30 VAC or VDC Alarm Output: Two Form C relay contacts each rated 1 A at 30 VAC or VDC for resistive loads 2 | DS160 Series High Performance Request‑to‑exit Detectors 21 Indicators: 1 activation LED Relay Latch Time: Adjustable from 0.5 sec to 64 sec. Ordering information DS160 Request‑to‑exit Detector For use in request-to-exit (REX) applications. Provides PIR 2.4 m x 3 m (8 ft x 10 ft) coverage, timers, door monitor with sounder alert, and pointable coverage. Order number DS160 DS161 Request‑to‑exit Detector Black enclosure. For use in Request-to-EXit (REX) applications. Provides PIR, 2.4 m x 3 m (8 ft x 10 ft) coverage, timers, door monitor with sounder alert, and pointable coverage. Order number DS161 Accessories TP160 Trim Plate A light gray trim plate used when mounting the detector over a standard single-gang box. Order number TP160 TP161 Trim Plate A black trim plate used when mounting the sensor over a standard single-gang box. Order number TP161 3 | DS160 Series High Performance Request‑to‑exit Detectors Represented by: North America: Europe, Middle East, Africa: Asia-Pacific: China: Latin America and Caribbean: Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, New York, 14450, USA Phone: +1 800 289 0096 Fax: +1 585 223 9180 security.sales@us.bosch.com www.boschsecurity.us Bosch Security Systems B.V. P.O. Box 80002 5617 BA Eindhoven, The Netherlands Phone: + 31 40 2577 284 Fax: +31 40 2577 330 emea.securitysystems@bosch.com www.boschsecurity.com Robert Bosch (SEA) Pte Ltd, Security Systems 11 Bishan Street 21 Singapore 573943 Phone: +65 6571 2808 Fax: +65 6571 2699 apr.securitysystems@bosch.com www.boschsecurity.asia Bosch (Shanghai) Security Systems Ltd. 203 Building, No. 333 Fuquan Road North IBP Changning District, Shanghai 200335 China Phone +86 21 22181111 Fax: +86 21 22182398 www.boschsecurity.com.cn Robert Bosch Ltda Security Systems Division Via Anhanguera, Km 98 CEP 13065-900 Campinas, Sao Paulo, Brazil Phone: +55 19 2103 2860 Fax: +55 19 2103 2862 latam.boschsecurity@bosch.com www.boschsecurity.com © Bosch Security Systems 2016 | Data subject to change without notice 2634909195 | en, V10, 10. Mar 2016 22 Page 1 of 3 CM-4085 and CM-5085 Series Mushroom Push Buttons INSTALLATION INSTRUCTIONS Door Activation Devices Faceplate Mushroom PushButton Connecting Wires 2 White & 2 Red Pneumatic Time Delay Timer Screw BACK VIEW 5. WIRING 1T DPST 2T Momentary: When the switch is pressed it will provide a change of state on both of the N.O. & N.C. poles until released THIS PACKAGE INCLUDES: 4. INSTALLATION1. GENERAL DESCRIPTION Camden Door Controls CM-4085 and CM-5085 Series Switches are heavy duty push buttons designed for industrial and commercial applications. CM-4085 buttons are 1-5/8 (40mm) in diameter, CM-5085 buttons are 2 3/8” (60mm) in diameter. They are available in red, blue, or green. All switches feature vandal resistance faceplate 1/4” [6mm] thick brushed aluminum, optional duranodic (US40) finish is also available. CM-4085 and CM-5085 series switches are supplied with 1-60 second pneumatic timer. Pneumatic timer features 6 amps @ 24VDC. 2. SPECIFICATIONS Voltage 12/24 VDC Contact Rating 6A @ 24 VDC Temperature Range -13°F to 158°F (-25°C to 70°C) Time Range: 1-60 Sec Timer Life: 1,000,000 activations Switch Type Momentary Contact Type: N-C, N-O, Form 2 Standard Finish Brushed Aluminum Dimensions CM-4185 NARROW: 4 1/2’’ H x 1 3/4’’ W x 2 1/8’’D (114mm X 44mm x 54mm) CM-4085 & CM-5085 SINGLE GANG 4 1/2’’ H x 2 3/4’’ W x 2 1/8’’D (114mm X 70mm x 54mm) 3. APPLICATION Camden CM-4085 and CM-5085 ‘Request To Exit’ Series Switches with built in pneumatic time delay are ADA (American Disabilities Act) compliant and are designed to de-energize electric locking devices (such as magnetic locks) on egress doors without reliance upon electrical power for their operation. The mechanical pneumatic timer is also adjustable, allowing flexible time control as required in the field. Select models comply with UL 294 (standard for access control systems) and are designed for use in access control installations meeting IBC (International Building Code) requirements. CM-5085 Pneumatic time delays require no power to operate. The timing range is 1 – 60 seconds and is easily adjusted by a thumbscrew. CM-4085 and 5085 Series mushroom push switches are heavy duty push buttons specially designed and manufactured to meet the stringent demands of exit control. No set screws are required, due to the bayonet interlocking of the modular assembly. Buttons are free spinning, for additional protection against vandalism. (1) 1-5/8’’ (40mm) Diameter button (CM-4085 series) or 2- 3/8’’ (60mm) Diameter button (CM-5085 Series) (1) Single Gang Die-cast Aluminum Faceplate (1) Pneumatic time delay. (1) Parts Kits CM-4085 WIRING LAYOUT & COLOR CODING SWITCH TYPE DPST N.O. DPST N.C. NORMALLY OPEN WHITE RED NORMALLY CLOSED WHITE RED 23 Page 2 of 3 CM-4085 AND CM-5085 SERIES MUSHROOM PUSH BUTTONS INSTALLATION INSTRUCTIONS 7. PARTS INFORMATION 3 4 6 7 8A 9 8B 5 B C A Mushroom button for CM-4085 Series 2B Mullion Faceplate for CM-4185 Series 1B 1A 2A 6. CM-4085 AND CM-5085 SERIES FRONT AND SIDE VIEW Tel: (905) 366-3377 www.camdencontrols.com A.OLISA PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CAMDEN DOOR CONTROLS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CAMDEN DOOR CONTROLS IS PROHIBITED. CM-4085 & CM-5085 SERIES BACK VIEW 18/08/20 5502 Timberlea Blvd. Mississauga, ON Canada L4W 2T7 23 4'' [70mm] 41 2'' [114mm] 1 4'' [6mm] 11 4'' [32mm] 21 8'' [54mm] 24 Page 3 of 3 CM-4085 AND CM-5085 SERIES MUSHROOM PUSH BUTTONS INSTALLATION INSTRUCTIONS Call: 1.877.226.3369 / 905.366.3377 Visit: www.camdencontrols.com Opening New Doors to Innovation, Quality and Support! File: CM-4085&5085_Manual.indd Revision: December 16th 2020 Part No: # 40-82B256 ORDERING INFORMATION FOR REPLACEMENT PARTS ITEM NUMBER PART NUMBER DESCRIPTION 1. A CM-4085 SERIES RED MOMENTARY MUSHROOM BUTTON (DIA. 1-5/8’’) 60-66A000 60-66A005 BLUE MOMENTARY MUSHROOM BUTTON (DIA. 1-5/8’’) 60-66A006 GREEN MOMENTARY MUSHROOM BUTTON (DIA. 1-5/8’’) B CM-5085 SERIES RED MOMENTARY MUSHROOM BUTTON (DIA. 2-3/8’’) 60-66A007 60-66A009 BLUE MOMENTARY MUSHROOM BUTTON (DIA. 2-3/8’’) 60-66A010 GREEN MOMENTARY MUSHROOM BUTTON (DIA. 2-3/8’’) 2. A 60-41A003 DIE-CAST ALUMINUM SINGLE GANG FACE PLATE 4 1/2’’H x 2 3/4’’W x 1 3/4’’D (114mm x 70mm x 44mm) B 60-41A004 DIE-CAST ALUMINUM MULLION FACE PLATE 4 1/2’’H x 1 3/4’’W x 1 3/4’’D (114mm x 44mm x 44mm) 3. 60-40G020 ALUMINUM BLOCK 4. 60-51Z051G20 M4-07 X 16MM PHILLIPS SCREW, CADMIUM PLATED 5. 60-51Z092B08 M3 X 8 HEX HD CAP SCREW 6. 60-40A004 MOUNT BRACKET 7. RM-1000/85M PNEUMATIC TIME DELAY PARTS KIT ITEM NUMBER PART NUMBER DESCRIPTION 8. 60-34B038 (A) 6-32 X 3/4 FLAT HEAD PHILLIPS ZINC PLATED SCREW (B) 6-32 X 3/4 SNAKE EYE TAMPER PROOF SCREW (C) TAMPER PROOF (SNAKE EYE) KEY BUTTON ENGRAVED (IN WHITE) OPTIONS ITEM NUMBER MODEL NUMBER ENGRAVED GRAPHIC DECRIPTION 9. CM-xxxE EXIT CM-xxxS EXIT / SORTIE CM-xxxS SORTIE CM-xxxESA EXIT / SALIDA CM-xxxH HANDICAP LOGO CM-xxxSA SALIDA COMPATIBLE MOUNTING BOXES ITEM NUMBER PART NUMBER DESCRIPTION 10. CM-66 FLUSH BOX & DRESS PLATE, STANDARD DEPTH BOX WITH 7’’ X 7’’ DRESS PLATE HEAVY GAUGE STAINLESS STEEL CM-31 SLEEVE COVER FOR STANDARD 2 3/4” X 4 1/4” (70MM X 108MM) SURFACE ELECTRICAL BOX. HEAVY GAUGE STAINLESS STEEL CM-CPC1 VANDAL AND WEATHER RESISTANT CLEAR LIFT COVER CM-34D SURFACE MOUNT BOX WITH EXTRA DEPTH HEAVY DUTY GREY POLYMER 4 1/2''H x 2 3/4''W x 1 3/4''D [114mm x 70mm x 44mm] MODEL NUMBERS MODEL NUMBER QTY DESCRIPTIONCM-4085 SERIES CM-5085 SERIES CM-4185 - 1 SPRING RETURN WITH MULLION FACEPLATE, DPST 1-60 SEC PNEUMATIC TIME DELAY REQUEST TO EXIT SWITCH CM-4085 CM-5085 1 SPRING RETURN, DPST 1-60 SEC PNEUMATIC TIME DELAY REQUEST TO EXIT SWITCH CM-4085RPTE CM-5085RPTE 1 SPRING RETURN, DPST 1-60 SEC PNEUMATIC TIME DELAY, RED BUTTON, ‘PUSH TO EXIT’. COMPLETE MODEL. NO ‘OPTIONS OR FINISHES’ AVAILABLE - CM-5085GPTE 1 SPRING RETURN, DPST 1-60 SEC PNEUMATIC TIME DELAY GREEN BUTTON, ‘PUSH TO EXIT’. COMPLETE MODEL. NO ‘OPTIONS OR FINISHES’ AVAILABLE 25 83 www.alarmcontrols.com | 800.645.5538 © 2021, Hanchett Entry Systems, Inc., an ASSA ABLOY Group company. | Patent pending and/or patent www.assaabloydss.com/patent ALARM CONTROLS Features Standard Features • Stainless steel wall plate accepts sta ndard 1-1/8” mortise cylinder • Tamp er-proof and slotted- head screws included • Morti se Cylinders not included, available separately (CY-1, CY-1A) Options • Momentary or alternate swi tch, see model chart • SPDT or D PDT, see model chart • No LED , green LED, green and red LEDs, see model chart • Pneum atic time delay: 2 to 45 seconds, see model chart • Add W P for weather resistant cover and surface mount box. Available for single gang models only. Specifications Electrical • Contacts rated 4A at 28 VDC • LEDs o perate on 12 or 24 VDC/VAC • Swit ch depth behind plate: 1-1/4” • Switc hes terminated in colored leads Operating Temperature • +15 to 120F Narrow or single gang mortise cylinder key switch stations. Choose between momentary action switch that remains active as long as it’s depressed, or alternate action switch that alternates between open (disconnected) and closed (connected) each time it's pressed. Available with LED options. MCK Series Mortise Cylinder Stations Switch Type 1.75" Wide 1.75" Wide Green LED 1.75" Wide Green LED Red LED Single Gang Single Gang Green LED Single Gang Green LED Red LED SPDT Momentary Action MCK-1 MCK-2 MCK-3 MCK-4* MCK-5* MCK-6* SPDT Alternate Action MCK-1-2 MCK-2-2 MCK-3-2 MCK-4-2* MCK-5-2* MCK-6-2* DPDT Momentary Action MCK-1-3 MCK-2-3 MCK-3-3 MCK-4-3* MCK-5-3* MCK-6-3* DPDT Alternate Action MCK-1-4 MCK-2-4 MCK-3-4 MCK-4-4* MCK-5-4* MCK-6-4* Pneumatic Time Delay (2 to 45 seconds) N/A N/A N/A MCK-4-5* MCK-5-5* MCK-6-5* *Weather resistant cover and surface mount back box available. Add "-WP" to model number for the weatherproof option. MCK-1 MCK-4 26 5502 Timberlea Blvd. Mississauga, ON Canada L4W 2T7 • Toll Free: 1 877 226-3369 (CAMDEN9) Tel: (905) 366-3377 • Fax: (905) 366-3378 • E-mail: info@camdencontrols.com • www.camdencontrols.com FEATURES ELECTRIFIED LOCKS, RELAYS & TIMERS RESTROOM CONTROL KITS ANNUNCIATORS TRANSFORMERS POWER SUPPLIES RELAYS & TIMERS DOOR ALARMS MAGNETIC LOCKS ELECTRIC STRIKES 7 DAY PROGRAMMABLE TIMER CX-247 RELAYS & TIMERS • MICROPROCESSOR CONTROL • 15 DAILY OR WEEKLY SCHEDULES • 16 ‘ON’ AND ‘OFF’ EVENTS • EXTREMELY COMPACT SIZE • MEMORY BACKUP • EASY MOUNTING • ’H’ MODELS FEA TURE ’FIRST-MAN-IN’ FUNCTION (HOLIDAY/SNOW DAY) • 16A@ 30 V DC CONTACTS • 3 YEAR WARRANTY Camden Door Controls is an ultra compact programmable 7 day timer. It features a large digital display, and 16 flexible easy-to-program on/off schedules. An internal permacell keeps the programs and display readable in the event of a power loss or brownout. The CX-247 can be ordered to operate on 12V, or 24V, AC/DC. The heavy duty relay contacts are rated at 16 amps @ 30 VDC. The ”First-Man-In” option maintains security during ”snow-days”, sick days, employee absenteeism. The timer schedule does not engage, (and the door remains locked) until the ”First-Man-In” activates the entry system. DESCRIPTION CX-247 APPLICATION The CX-247 can automatically and reliably control electrified locks and magnets, automatic overhead and pedestrian doors, or control lighting or energy management devices. The ”First-Man-In” option eliminates the need for a complex 365-day timer. The compact size and dust and water resistant enclosure, ensure it will meet virtually any timing application. 27 5502 Timberlea Blvd. Mississauga, ON Canada L4W 2T7 • Toll Free: 1 877 226-3369 (CAMDEN9) Tel: (905) 366-3377 • Fax: (905) 366-3378 • E-mail: info@camdencontrols.com • www.camdencontrols.com MKTG-LIT-SP-247-R5 7 DAY PROGRAMMABLE TIMER TYPICAL APPLICATION SPECIFICATIONS CX -247-1 2 CX-247-24 OPERATING VOLTAGE: 12V AC/DC 24 V AC/DC DIMENSIONS: 2 3/8” H x 2 3/8” W x 1 1/4” D ( 60mm x 60mm x 32mm ) MOUNTING: 4 MOUNTING SCREWS ENCLOSURE: WHITE ABS PLASTIC CURRENT DRAW: 0.1 MA IDLE, 10 MA OPERATING RESPONSE TIME: .03 SECONDS BACK UP: INTERNAL PERMACELL PROGRAMS: 16 RELAY OUTPUTS: 1 X FORM ’C’ (SPDT) CONTACT RATING: 16 AMPS @ 30 VAC ELECTRICAL LIFE: 250,000 @ RATED CAPACITY DOOR O PERAT O R O R AC/D C POWE R ELECTR I C LOC K CX-247 ORDERING INFORMATION MODEL DESCRIPTION CX-247-12: 7 DA Y TIMER - 12V CX-247-24: 7 DA Y TIMER - 24V CX-247H-12: 7 DA Y TIMER WITH FIRST-MAN-IN-FUNCTION - 12V CX-247H-24: 7 DA Y TIMER WITH FIRST-MAN-IN-FUNCTION - 24V 28 Input Voltage 115VAC, 60Hz, 0.6 A Trigger Access control trigger input Outputs Two (2) Class 2 Rated power-limited outputs - Fail-Safe/Fail-Secure lock output (switched) - Auxiliary power output (unswitched) Voltage 12VDC or 24VDC selectable Current 1.75A continuous max. Other Short circuit and thermal overload protection Back-up Battery (not included) Type Sealed lead acid or gel type Failover Upon AC loss, instantaneous Fire Alarm Disconnect Supervised Latching or non-latching Supervision AC Failure Form “C” contacts Indicators (LED) Input Input voltage is present DC Output Powered Agency Listings UL UL294 (Access Control) cUL CSA Standard C22.2 No.205-M1983, Signal Equipment CSFM CSFM Approved Physical and Environmental Dimensions (H x W x D) Enclosure: 13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm) Shipping: 15” x 13.875” x 4.75” (381mm x 352.4mm x 120.6mm) Enclosure accommodates up to two (2) 12VDC/7AH batteries Weight (approx.) Product: 8.4 lb. (3.81 kg) Shipping: 9.4 lb. (4.26 kg) Temperature Operating: 0ºC to 49ºC (32ºF to 120ºF) Storage: – 20ºC to 70ºC (– 4ºF to 158ºF) Relative Humidity 85% +/ – 5% BTU/Hr. (approx.) 12VDC: 11 BTU/Hr. 24VDC: 22 BTU/Hr. Specifications AL175ULX AL175ULX Switching Power Supply/Charger Altronix AL175ULX Switching Power Supply/Charger converts a 115VAC 60Hz input into two (2) individually PTC protected auto-resettable 12VDC or 24VDC outputs. Lifetime Warranty Altronix Corporation | 140 58th St | Brooklyn, NY 11220 USA phone: +1 718.567.8181 | fax: +1 718.567.9056 | email: info@altronix.com | www.altronix.com Rev. 07222022 29

Source: City of Mauldin website. First collected Nov 7, 2026.