Called Unified Zoning & Development Ordinance Committee meeting
Town of Chapin · Lexington County · meeting of Jun 6, 2023 · Agendas
Open the original document More from Town of Chapin
Text
Extracted automatically from the original. Tables and formatting may not survive; the original document is authoritative.
CHAPIN UNIFIED ZONING & DEVELOPMENT ORDINANCE
STEERING COMMITTEE SPECIAL CALLED MEETING
Town Hall
June 6, 2023
3:00 P.M.
AGENDA
Call to order
Freedom of Information Act Compliance
New Business
1. Draft Review
a. Article 8: Parking & Loading
b. Article 9: Signs
Adjourn
RG MRB GROUP - Article 8 – Version 3 – 5.22.23
Article 8 – Off-Street Parking Standards
8. Off-Street Parking Standards
8.1. Purpose and Intent
Parking lots and similar facilities are necessary elements in the urban environment.
However, the provision of parking facilities must be regulated to avoid negative impacts
such as increased stormwater volumes, heat islands, reduced traffic efficiency,
interruption of a vibrant streetscape and other recognized externalities of parking lots.
The purpose of this section is to ensure the adequate provision of parking in Chapin
without degrading the built or natural environment, and to provide clear regulations
regarding the location, sizing, and screening of off-street parking facilities. It is intended
that these standards will ensure the development of parking in a manner consistent
with the desired character and development patterns of the community.
8.2. Applicability
8.2.1. New Development
All new development shall provide off-street parking and loading areas in
accordance with the standards of this Section
8.2.2. Existing Development
8.2.2.1. Change in Use
Additional off-street parking or loading facilities are not required when
a building’s use changes from one conforming use to another
conforming nor when a non-conforming use is converted to a
conforming use. (need to discuss this – parking demands can vary
greatly).
8.2.3. Building Expansion
If an existing structure is expanded or enlarged in terms of the number of
dwelling units, more than 20% of its floor area, or is otherwise significantly
improved any additional off-street parking and loading spaces that may be
required due to the improvement shall be provided in accordance with the
requirements of this Section as applied only to the expanded or enlarged part of
the structure.
8.2.4. Historic Buildings
Renovations to a designated building on the National Register, by the State SCDAH
or NPS that undertake expansions under 25% of the number of dwelling units,
floor area, or other work requiring a certificate of appropriatness or zoning
permit shall not require additional off-street parking or loading facilities.
8.2.5. Timing of Review
RG MRB GROUP - Article 8 – Version 3 – 5.22.23
Review for compliance with the standards of this Article shall occur during
review of a development application for a planned development, site plan,
subdivision, or zoning permit, as appropriate.
8.2.6. Parking Plan Required
All development applications subject to review for compliance with the
standards of this Article shall include a parking plan which shall accurately
convey compliance with this section.
8.3. General Standards
8.3.1. Use of Parking
Off-street parking areas required by this Section shall be used solely for the
parking of licensed motorized vehicles in operating condition. Required parking
spaces shall not be used for the sale, lease, storage, dismantling, or service of
any vehicles, boats, motor homes, campers, mobile homes, building materials,
equipment, or supplies except for farmer’s markets and food trucks on a
temporary basis.
8.3.2. Identified as to Purpose
Off-street parking areas shall include painted lines, wheel stops, or other
methods of identifying individual parking spaces and distinguishing such spaces
or berths from an aisle.
8.3.3. Surfacing
8.3.3.1. Except as provided for in section 8.3.3.2 and 8.3.3.3 below, all off-street
parking areas shall be surfaced with asphalt, concrete, brick, stone,
pavers, or an equivalent hard, dustless, and bonded surface material.
Use of surfacing that includes recycled materials (e.g., glass, rubber,
used asphalt, brick, block, and concrete) is encouraged. These surfaces
shall be maintained in a smooth, well-graded, clean, orderly, and dust-
free condition.
8.3.3.2. The use of pervious or semi-pervious parking lot surfacing materials—
including, but not limited to—pervious asphalt and concrete, open joint
pavers, and reinforced grass/gravel/shell grids may be approved for off-
street parking and loading areas, provided such surfacing is subject to an
on- going maintenance program (e.g., sweeping, annual vacuuming).
8.3.3.3. Off-street parking spaces and driveways for single-family detached, two-
family, and townhouse dwellings may utilize pervious material such as
crushed stone or gravel. This shall not include major subdivision unless
specifically approved or conditioned by the Planning Commission.
8.3.4. Maneuvering
RG MRB GROUP - Article 8 – Version 3 – 5.22.23
Off-street parking areas shall be arranged so no parking or maneuvering
incidental to parking shall occur on a public street or sidewalk.
8.3.5. Parking in Front of a Residential Structure
Except within a driveway surfaced as provided in Subsection 8.3.1.3, the parking
of any vehicle is prohibited within the front yard. Parking of vehicles in the side
or rear yard must be screened from the public right-of-way. (How are they to be
screened? – what if driveway is to the side of house?).
8.3.6. Americans with Disabilities Act
All parking facilities that require accessible parking spaces shall ensure that a
portion of the total number of required parking spaces shall be specifically
designated, located, and reserved for use by persons with physical disabilities, in
accordance with the standards in the federal American with Disabilities Act
(ADA).
8.3.7. Parking of Recreation, Commercial, and Unlicensed Vehicles
8.3.7.1. No recreational vehicle shall be parked or stored on any lot in a
residential district for more than twenty-four (24) hours, other than in a
carport, enclosed building, or rear yard. The Board of Zoning Appeals
may grant a variance in case of unnecessary hardship.
8.3.7.2. No vehicle or trailer subject to State licensing which does not display a
current license plate shall be parked or stored on any lot in a residential
district, except in an enclosed building or in the rear yard.
8.3.7.3. No more than one travel or camping vehicle per family living on the
premises shall be permitted to be parked on a lot in any residential
zone; and the vehicle shall not be occupied temporarily or permanently
while it is parked or stored, except in an authorized mobile home park.
8.3.7.3.1. Exception: In Rural Agricultural (RA) or Rural Residential
(RR) the Administrator may grant temporary stays of camping or
recreational vehicle in the form of a zoning permit. Temporary
stays shall not exceed more than 120 total calendar days within
a 12-month period.
8.3.7.4. Trucks, tractors, or tractor-trailers having a capacity of more than an
8,000-pound load, front- and rear-end loaders, or any kind of
commercial, industrial, agricultural and transportation
vehicles/equipment used primarily for business purposes, shall not be
parked or stored on or adjacent to any parcel in residential district for
purposes other than unloading, loading, or delivery services. This
excludes vehicles or trailers approved under the Home Occupation
requirements.
8.4. Minimum Off-Street Parking Requirements
RG MRB GROUP - Article 8 – Version 3 – 5.22.23
8.4.1. Except as otherwise expressly stated, off-street motor vehicle parking spaces
shall be provided in accordance with the following table:
Table 8.4.1: Minimum Number of Off-Street Vehicle Parking Spaces
Principal Use Parking Standards
Residential Uses
Accessory Dwelling Unit 1 space per unit, in addition to principal use standards
Bed and Breakfasts 1 space per unit, in addition 1 off-street space shall be
reserved for the owner and 1 for staff (such as a
housekeeper)
Day Care Home 2 space per unit, in addition 1 space shall be reserved for
each employee on shift
Dwelling, Detached Single
Family
2 space per unit
Dwelling, Two-Family 1 space per unit
Dwelling, Three-Family 1 space per unit
Dwelling, Multi-Family 1.5 per unit
Rowhome 1 space per unit
Group Home, Small and Large 1 space per 3 beds, with 1 space for each employee or
supervisor on shift
Manufactured Home 2 space per unit
Nursing Homes 1 parking space per 6 beds, in addition to 1 space per
employee during peak-hour shift.
Short Term Rental 1 independently accessible parking space per unit, no
tandem parking allowed.
Commercial
Automobile Service Station 1 space per 2 employees at peak shift, in addition 1 space
per 150 square feet of the automobile repair space
Automobile, ATV, Motorcycle or
Boat Sales
1 space per 2 employees at peak shift, in addition 1 space
per 150 square feet of the automobile repair space (if
applicable) All vehicles for sale shall be located on paved
surfaces.
Automotive Parts Store 1 space per 400 square feet of gross floor area
Bars and Nightclubs 1 space per two seats or 1 space for every 75 sq. ft. of bar
area, including outdoor areas, whichever is greater
Car Wash 1 space per peak hour employee, and 1 space per bay.
Catering Service 1 space per 400 square feet of gross floor area
Check Cashing 1 space per 400 square feet of gross floor area
Commercial Day Care Center 2 spaces per peak shift employee
Convenience Store 1 space per 400 square feet of gross floor area
Drive-In Movie Theaters 1 space per speaker outlet
Dry Cleaning 1 space per 600 square feet of gross floor area
Financial Institutions 1 space per 400 square feet of gross floor area
Funeral Homes 1 space per 4 seats within the sanctuary (if applicable)
and/or 1 space per 2 employees, whichever is greater
Garden Centers 1 space per 400 square feet of gross floor area
General Retail 1 space per 200 square feet of gross floor area
RG MRB GROUP - Article 8 – Version 3 – 5.22.23
Hardware Store 1 space per 400 square feet of gross floor area
Hotels/Motels 1 space for each room to be rented, in addition to 1 space
per 2 employees at peak shift
Indoor Storage 1 space per peak employee and 1 space per 5 leasable
units.
Liquor Stores 1 space per 400 square feet of gross floor area
Microbrewery, Micro-Distillery,
or Micro-Winery
1 space per 300 square feet or 1 space per two seats,
whichever is greater
Miniature Golf 4 spaces per hole, plus 1 space for every 2 employees on
peak shift
Mixed-Use Building 2 spaces per unit in addition to parking requirement for
other associated use
Office Building 2 spaces for each 1,000 square feet of leasable floor area,
plus 1 space for each 2 employees
Office, Medical 1 space per 400 square feet of gross floor area
Office, Non-medical 1 space per 400 square feet of gross floor area
Personal Service 1 space per 400 square feet of gross floor area
Pet Boarding 1 space per 400 square feet of gross floor area
Restaurant, Full-Service 1 space per two seats or 1 space for every 75 sq. ft. of
dining area, including outdoor areas, whichever is greater
Sexually Oriented Businesses 1 space per 400 square feet of gross floor area
Specialty Retail 1 space per 400 square feet of gross floor area
Tattoo Parlor 1 space per 400 square feet of gross floor area
Vape or E-Cig Store and Lounge 1 space per 400 square feet of gross floor area
Veterinarian 1 space per 400 square feet of gross floor area
Institutional, Civic, or Public
Amphitheaters 1 space per 4 seats
Cemetery and Mausoleums 4 spaces per acre, plus 2 spaces per employee on shift
Civic and Social Organizations 1 space per 600 square feet of gross floor area
Colleges, Universities, and
Vocational Schools
1 space per 4 students at maximum capacity in addition to
requirements for associated uses
Elementary Schools 1 space for each vehicle owned and operated by school
staff and 2 spaces per classroom or administrative office
Farmers Market, Indoor 2 spaces per booth or vendor or 1 space per 400 square
feet of gross floor area, whichever is less
Farmers Market, Outdoor 2 spaces per booth or vendor or 1 space per 400 square
feet of gross floor area, whichever is less
Golf Course 4 spaces per hole, plus 1 space for every 2 employees on
peak shift
Government Building or Facility 1 space per 400 square feet of gross floor area
Hospital 1 space per 2 beds intended for patients, and 1 space for
each 3 employees during peak shift
Kindergarten or Preschool 1 space for each vehicle owned and operated by school
staff and 2 spaces per classroom or administrative office
Public Utility Stations 1 space per employee per shift
Recreational Facilities 10 spaces per athletic field or 4 spaces per .25 acre of
areas dedicated to use, whichever is greater
RG MRB GROUP - Article 8 – Version 3 – 5.22.23
Religious Assembly 1 space per 4 seats in the main assembly room
Secondary Schools 1 space for each vehicle owned and operated by school
staff and 2 spaces per classroom or administrative office
Sports Stadium 1 space per 4 seats in addition to 1 space per peak hour
employee
Theater 1 space per 4 seats
Transportation Terminal (Bus
and Rail)
1 space per 2 passenger of a peak hour for departures and
arrivals, including accounting for multiple buses or trains
Industrial
Animal Shelters 1 space per 400 square feet of gross floor area
Correctional Facility 2 spaces per peak hour employee in addition to 1 space for
every vehicle owned and operated by the facility
Crematory 1 space per 600 square feet of gross floor area
Heavy Equipment Rental 1 space per 2 employees at peak shift, in addition 1 space
per 150 square feet of the automobile repair space (if
applicable) All vehicles and equipment for rent shall be
located on paved surfaces.
Indoor Shooting Range 1 space per 400 square feet of gross floor area
Junk Yard or Scrap Yard 2 spaces per employee at peak shift
Manufacturing or Production
Facility
1 space per 1,000 square feet of gross floor area in
addition to 1 space per employee at peak shift
Outdoor Shooting Range 2 spaces per shooting bay, in addition to 1 space per
employee at peak shift
Outdoor Storage 1 space per 400 square feet of gross floor area, in addition
to 1 space per employee at peak shift
Repossession Services 1 space per 400 square feet of gross floor area, in addition
to 1 space per employee at peak shift
Truck Sales and Service 1 space per 2 employees at peak shift, in addition 1 space
per 150 square feet of the automobile repair space (if
applicable) All vehicles for sale shall be located on paved
surfaces.
Warehouse 1 space per 1,000 square feet of gross floor area in
addition to 1 space per employee at peak shift
Wholesale Trade 1 space per 1,000 square feet of gross floor area in
addition to 1 space per employee at peak shift
8.4.2. Districts Excluded
There shall be no minimum off-street parking spaces required within the Town
Center.
8.4.3. Planned and Negotiated Development Districts
Within Planned Development Districts, required off-street parking standards
shall be determined during review of the application.
8.4.4. Unlisted uses
RG MRB GROUP - Article 8 – Version 3 – 5.22.23
An applicant proposing to develop a principal use that is unlisted in Section
8.4.1: Minimum Number of Off-Street Parking Spaces, shall propose the amount
of required parking by one of the methods outlined below:
8.4.4.1. Apply the minimum off-street parking space requirement specified in
Section 8.4.1 for the listed use that is deemed most similar to the
proposed use; or
8.4.4.2. Conduct a parking demand study by a transportation or traffic engineer
or other experienced professional to demonstrate the appropriate off-
street parking space requirement. The study shall estimate parking
demand based on the recommendations of the ITE, ULI or another
acceptable source of parking demand data. This demand study shall
include relevant data collected from uses or combinations of uses that
are the same or comparable to the proposed use in terms of density,
scale, bulk, area, type of activity, and location.
8.4.5. Maximum Number of Off-Street Parking Spaces
Except as otherwise stated within this Article, the maximum number of off-
street parking spaces provided shall not exceed 125 percent of the minimum
provided in Table 8.4.1.
8.4.6. On-Street Parking
Uses may count on-street parking spaces on public street rights-of-way abutting
the subject property towards the off-street motor vehicle parking minimums.
8.4.7. Alternate Compliance
The parking ratios of this section are not intended to prevent development or to
make development economically impractical. To allow for flexibility in
addressing the expected parking demand, alternative off-street parking
requirements may be approved by the Zoning Board of Appeals under the
variance proceedings in Section 10.12.If the applicant chooses to apply for a
variance, the applicant shall provide a parking study or a parking demand
management plan demonstrating that the parking requirements in Table 8.4.1
do not accurately reflect the parking demand that can reasonably be anticipated
for the proposed use.
8.4.8. Fractions
When measurements of the number of required spaces result in a fractional
number, any fraction of less than one-half is rounded down to the next lower
whole number, and any fraction of one-half or more is rounded up to the next
higher whole number.
8.4.9. Bicycle Parking
A minimum of five (5) bicycle parking spaces is required for all uses requiring
twenty-five (25) parking spaces. Thereafter, an additional two (2) bicycle parking
RG MRB GROUP - Article 8 – Version 3 – 5.22.23
spaces is required for each additional twenty-five (25) parking spaces. Bicycle
parking facilities shall be standard bicycle racks or other secured lockable
facilities. When feasible, the bicycle facilities shall be located near the entrance
to the building.
8.5. Design Standards for Parking Lots
8.5.1. Dimensional Standards for Parking Spaces and Aisles
Except as otherwise provided, standard vehicle parking spaces and aisles shall
comply with the minimum dimensional requirements established in Table 8.5.1:
Dimensional Standards for Parking Spaces and Aisles.
Table 8.5.1: Minimum Dimensional Standards for Parking Spaces and Aisles
Parking
Angle
Staff Width Stall Depth Drive Aisle
Width*
Stall Length
Along Curb
Double Row
+ Aisle, Curb
to Curb*
A B C D E F
0 8’ 8’ 12’ 20’ 48’
30 9’ 16.8’ 12’ 18’ 45.6’
45 9’ 19.1’ 12’ 12.7 50.2
60 9’ 20.1’ 14.5’ 10.4’ 54.7’
90 9’ 18’ 24’ 9’ 60’
8.5.2. Front Yard Parking Not Allowed
Within the Town Center and Village Commercial Zoning Districts, off-street
parking shall not be permitted within the Front Yard.
8.5.3. Off-Site (Satellite) Parking
Except for spaces provided subject to the Americans with Disabilities Act,
required Off-Street Parking spaces may be provided on a separate lot which
RG MRB GROUP - Article 8 – Version 3 – 5.22.23
does not contain the proposed use or structure subject to the following
standards:
8.5.3.1. New off-Site parking areas must comply with all applicable parking area
design and accessibility standards.
8.5.3.2. Off-site parking areas must be located within a 1,200-foot publicly
accessible and established walking distance of the entrance of the use
served by such parking.
8.5.3.3. The walking distance between the off-site parking areas and the primary
pedestrian entrances to the uses shall consist of a walkway protected by
landscape buffer or a curb separation and elevation from the street
grade. Periodic crossings at established crosswalks are allowable.
8.5.3.4. The right to use the off-site parking must be evidenced by a deed, lease,
easement, or similar written instrument establishing such use, for the
duration of the use.
8.5.3.5. Off- Site Parking shall not be provided within Residential Zoning
Districts.
8.5.4. Shared Parking and Parking Reductions
When two or more uses share common parking facilities, the minimum amount
of required parking may be reduced. The minimum amount of required parking
shall be calculated as the sum of the required parking for the 2 uses separately,
divided by the factor listed in the table below. The Zoning Administrator will
classify the uses in the categories in the table prior to the calculation of off-
street parking requirements. In all cases, the burden to demonstrate that a
reduction in parking requirements is warranted shall rest with the applicant.
Shared Parking Reductions
Residential Lodging Office Retail/Restaurant
Residential 1.0 1.1 1.4 1.2
Lodging 1.1 1.0 1.7 1.3
Office 1.4 1.7 1.0 1.2
Retail/Restaurant 1.2 1.3 1.2 1.0
8.5.5. Additional Parking Reductions: The Zoning Administrator may grant a reduction
in the parking requirements set forth in this section in the following cases:
8.5.5.1. Where uses in the same or adjoining development, having different
peak hour demand, seek to share parking, the applicant must submit to
the administrator an analysis and substantiated projections of peak
parking demand — based on historic data from other locations or a
similar use or a parking study — for the entire development to justify
the shared use of parking spaces for separate uses.
8.5.5.2. Where the special nature of a certain development (e.g., special types
of housing projects inhabited by persons with low or no automobile
ownership) does not require the amount of parking listed in Table 8.4.1
RG MRB GROUP - Article 8 – Version 3 – 5.22.23
8.5.5.3. Where fewer parking spaces are needed due to location and use — e.g.,
if there is a high concentration of residential units adjacent to a
neighborhood-serving use, a parking reduction may be warranted.
8.5.6. The Administrator shall consider the following in determining whether a
reduction is warranted and make the following findings in writing:
8.5.6.1. The likelihood that the reduced number of parking spaces can satisfy
demand;
8.5.6.2. The amount of time during the year when the number of spaces
provided may be insufficient and the amount of resulting parking
overflow;
8.5.6.3. The impact of periodic overflows upon the public streets and other
parking facilities;
8.5.6.4. The nature of surrounding land uses, character of surrounding road
system, and nearby circulation pattern.
8.6. Parking Lot Screening and Landscaping
8.6.1. Parking Lot Screening
8.6.1.1. Applicability: All new or expanded parking areas shall be screened from
the public right-of-way or primary vehicular access point(s) with
vegetation. An opaque screen is intended to exclude all visual contact
with the screened feature from an adjacent property, public street, or
right-of-way. An opaque screen may be composed of a wall, fence,
building, or berm; planted vegetation; existing vegetation; or a
combination thereof; as approved by the Zoning Administrator. Parking
lot screening is not required where property or street buffers are
retained or required.
8.6.1.2. Minimum Height of Screen: Shall include a hedge, dense shrub planting,
masonry wall, wood fence, or combination of such features that results
in a continuous visual screen along the length of its frontage. Hedges
and shrubs may be installed at a height of 2’, as long as the species
selected grows to at least 4’ in height within 4 years of installation.
8.6.1.2.1. Exceptions may be granted by the Zoning Administrator
where the parcel has irregular configuration, utility easements
or legal constraints which prevent compliance.
8.6.1.3. Minimum Length of Screen: The length of a required screen shall be that
which is necessary to totally visually screen the feature from protected
properties, streets, and rights-of-way as provided in this section. The
Zoning Administrator may approve accommodations for reasonable
access and use, as necessary.
8.6.1.4. Minimum Plantings: Parking lot screens shall comply with the
following landscaping standards:
RG MRB GROUP - Article 8 – Version 3 – 5.22.23
8.6.1.4.1. A parking lot shall contain at least one large maturing
tree for every 40 linear feet of street frontage, excluding
portions of the frontage where driveways are located and areas
necessary to avoid intrusion into clear sight triangles. Existing
trees preserved or planted within required buffer may count
towards this requirement.
8.6.1.4.2. Where there are conflicts with other planting
regulations, the more stringent regulation shall apply, as
determined by the Zoning Administrator.
8.6.2. Parking Area Interior Landscaping
8.6.2.1. Applicability: The following shall comply with the standards in this
subsection:
8.6.2.1.1. Any new vehicular surface area (parking lot) whether
principal or accessory use containing 10 or more parking spaces;
or,
8.6.2.1.2. Any new, additional, or expanded portion of an existing
vehicular surface area which cumulatively would create greater
than 10 parking spaces.
8.6.2.2. General Standards
8.6.2.2.1. No parking space shall be further than 60’ linear feet
from a large maturing tree.
8.6.2.2.2. One large maturing tree shall be required at the end of
every row of parking. This includes trees located within
required landscape islands.
8.6.2.2.3. Landscaped areas within or adjacent to parking areas
must be protected from vehicular damage by a raised curb,
wheel stops or approved equivalent barrier of at least six inches
in height.
8.6.2.2.4. Creative landscaping plans that incorporate larger
islands or different spacing of landscaped areas than required in
this section may be approved by the Zoning Administrator, as
long as the minimum area of landscaping and minimum number
of trees is provided. Appeals to this determination are made to
the Architectural Review Board for final decision.
8.6.2.3. Landscape Islands
8.6.2.3.1. Landscape islands shall be provided within each row of
parking spaces so that the maximum amount of uninterrupted
parking spaces is no greater than twelve (12).
8.6.2.3.2. No more than 12 continuous parking spaces shall be
permitted in a row without an interrupting landscaped island,
except in the following circumstance:
RG MRB GROUP - Article 8 – Version 3 – 5.22.23
8.6.2.3.2.1. The parking lot is gravel, or covered with other
soft pervious pavement materials, and spaces are not
striped.
8.6.2.3.3. Landscaped islands with a planting area of at least 12
feet wide by 18 feet long area shall be established parallel to
parking spaces and at the end of the parking aisle in order to
separate the last space from any adjacent driveways.
8.6.2.3.4. Islands shall be curbed for traffic control and safety.
8.6.2.3.5. At least one (1) large maturing tree shall be provided
within each landscaped peninsula. All landscaped peninsulas
and medians shall be landscaped with mulch, sod, shrubs, or
ground cover vegetation. If there is a conflict with overhead
utilities, one small or medium maturing tree is permitted per
island.
8.6.2.4. Building Exterior Perimeter Plantings
8.6.2.4.1. Plant material is required along 10 percent of the length
of exterior building walls and structures to provide separation
between the building and the vehicular surface area.
8.7. Pedestrian Access
In parking areas with more than 40 spaces, an on-site circulation system for pedestrian
and non-motorized travel must be provided in accordance with the following
requirements.
8.7.1. Connection to the Street
The on-site pedestrian circulation system shall connect all adjacent public rights-
of-way, adjacent sidewalks, multi-use paths, public spaces to any main building
entrance. The connection must follow a direct route and not involve significant
out-of-direction travel for system users.
8.7.2. Connection to Abutting Properties
The on-site pedestrian circulation system must provide connection to existing
paths and sidewalks on abutting properties or to the likely location of future
paths or sidewalks on those properties. When the Zoning Administrator
determines that no paths or sidewalks exist on a neighboring property or it is
not possible to determine the likely location of future path or sidewalk
connections or extending a connection would create a safety hazard on either
property, no such connection is required.
8.7.3. Internal Connections
The on-site pedestrian circulation system must connect all buildings on the site
and provide connections to other areas of the site likely to be used by
pedestrians and non-motorized travel, such as parking areas, bicycle parking,
RG MRB GROUP - Article 8 – Version 3 – 5.22.23
recreational areas, common outdoor areas, plazas, and similar amenity features.
The Planning Commission may require pedestrian pathways within the parking
area.
8.7.4. Design
Required on-site pedestrian circulation facilities must be designed and
constructed in accordance with the following requirements:
8.7.4.1. The on-site pedestrian circulation system must be paved and be at least
five feet in width.
8.7.4.2. When the on-site pedestrian circulation system crosses driveways,
parking areas or loading areas, it must be clearly differentiated through
the use of elevation changes, a different paving material or other
equally effective methods. Striping does not meet this requirement.
8.7.4.3. When the on-site pedestrian circulation system is parallel and adjacent
to a motor vehicle travel lane, it must be a raised path at least six inches
above the vehicle travel lane surface or be separated from the vehicle
travel lane by a raised curb, bollards, landscaping or another physical
barrier. If a raised path is used, the ends of the raised portions must be
equipped with accessible curb ramps.
8.7.4.4. The on-site pedestrian circulation system must be illuminated to ensure
that it can be used safely at night by employees, residents, and
customers. Lighting shall meet the requirements of Section 8.8.
8.7.5. Parking Lot Connections
Applicability: Adjoining parking lots serving non-residential and multifamily uses
shall be interconnected when feasible according to the following requirements:
8.7.5.1. At least one connection shall be provided at all common lot lines that
share a boundary of at least 60 feet.
8.7.5.2. Where feasible, the connection shall align with any previously
established connection on an adjacent property.
8.7.5.3. An easement for ingress and egress to adjacent lots through the
connection(s) shall be recorded in the form of an easement and
documentation submitted to Town Staff.
8.7.5.4. In the event these conditions cannot be met without undue hardship,
the Zoning Administrator may waive or adjust the connection
requirements as appropriate.
8.8. Lighting
8.8.1. Applicability: All parking lots serving non-residential and multifamily uses shall
be required to adhere to the following standards. Additionally, all newly
installed lighting fixtures shall adhere to the following standards, unless
installed by a state or federal agency.
RG MRB GROUP - Article 8 – Version 3 – 5.22.23
8.8.2. Standards and Design Requirements
8.8.2.1. Height: Lighting standards in parking lots shall not exceed a maximum of
25 feet in height.
8.8.2.2. Shielding: Lighting shall have a cutoff angle of 90° or less (full cutoff) and
be shielded from the sky and adjacent properties and structures
through shielding.
8.8.2.3. Light trespassing: The maximum light trespass at the property line shall
be 0.5 foot-candle.
8.8.2.4. Design? – Fixture design maybe elevated to ARB? PC to consider
placement and photometrics?
MRB Group – RG Revision 5.23.23 – Version 2
Article 9 – Signs
9. Signs
9.1. Purpose and Intent
The purpose of the regulations, here in, is to establish requirements for the placement,
installation, and maintenance of business and/or advertising signage, and to aid in the
preservation, protection, health, welfare, safety, and general well-being of the
Community and its Citizens..
This Ordinance will promote, authorize and enforce the use of on-premises signage
which are, but not limited to:
• Compatible with their surroundings;
• Appropriate for the type of activity to which they pertain;
• Tastefully expressive of the identity of the owner, occupant, and/or individual
proprietors or of the community as a whole;
• Designed to convey a desired message and/or image regarding the Owner,
Occupant, or individual prporitetor of a specific property, while protecting the
aesthetic and attractive qualities of the community;
• Minimize interference, obstruction, distraction, and/or unsafe conditions to the
motoring public; and,
• Conserve the value of the subject property and encourage the most appropriate
use of land throughout the municipality.
9.2. Applicability
Except as otherwise noted, the regulations of this article shall apply to all zoning
districts, and a zoning permit shall be required for the erection, placement, alteration,
or reconstruction of any sign.
9.3. General Provisions
9.3.1. Placement
Signs shall not be posted, placed, or erected within any public rights-of-way or
on any fixed or immovable object, such as, trees or utility poles, except as
specifically permitted or where encroachments have been specifically permitted
within or by this article.
9.3.2. Materials
Sign structures shall be constructed of durable, weather-resistant materials such
as treated lumber, concrete, metal, brick, or other similar substitute or
composite materials as determined by the Administrator. Unfinished wood,
cardboard, polystyrene foam, and similar materials are not permitted.
9.3.3. Design
The design, color, location, and illumination of signage shall be compatible and
complimentary of the overall design of the development and surrounding
parcels.
MRB Group – RG Revision 5.23.23 – Version 2
9.3.4. Sign Illumination
9.3.4.1. Internal Illumination: The background of internally illuminated cabinet
signs shall be completely opaque. This provision does not apply to
internally illuminated channel letters. Internally illuminated signs shall
be fully encapsulated and shall not allow the light intensity or brightness
of the sign to interfere with the safe vision of motorists or bicyclists.
LED lighting is prohibited within the Town Center (TC) zoning district.
9.3.4.2. Shielding: Unless otherwise expressly prohibited, signs may be
externally illuminated provided that lighting used illuminates the
surface area of the sign only, and is shaded, shielded, or directed so that
the light intensity or brightness does not interfere with the safe vision of
motorists or bicyclists. Around external lighting, landscaping shall be
designed to conceal the base of the light fixture to the extent feasible.
9.3.4.3. Transition of Electric Signs: Electric letter signs, (LED, & such), must
maintain message 6 seconds before changing, and cannot blink, scroll,
rotate, change height or intensity. Such signs electrical connections
must be inspected by Lexington County and a Zoning Permit must be
obtained.
9.3.4.4. Proximity to Residential Districts: No commercial sign within 100 linear
feet of a pre-existing residential structure may be illuminated between
the hours of 12:00 midnight and 6:00 a.m. A residence shall be deemed
"pre-existing" for purposes of this Section if it has a valid building permit
in effect for construction of said structure or if construction of said
structure was complete on or prior to the effective date of this
provision. This does not included residences in mixed use buildings in
the Town Center, Village Commercial, nor does it include multi-family
buildings.
9.3.5. Computation of Sign Area
The area of a sign shall be the area of the sign face formed by a perimeter
consisting of a series of straight lines enclosing all parts of the sign. Signs that
are composed of individual symbols, letters, figures, illustrations, message,
forms, or panels, the sign area shall be considered to include all lettering,
wording, and accompanying designs and symbols. Sign area shall also include
any background material, panel, trim, color, and direct or self-illumination used
that differentiates the sign from the building, structure, backdrop surface, or
object upon which or against which it is placed. The sign structure shall not be
included as a portion of the sign face, provided that no message, symbol, or any
of the aforementioned sign face criteria are displayed on, or designed as part of,
the sign structure.
9.3.6. Computation of Sign Height
MRB Group – RG Revision 5.23.23 – Version 2
Height shall be measured from the edge of the adjoining sidewalk, street, or the
natural grade to the highest point on the sign. Architectural elements related to
the support structure may extend up to 1 foot over the permitted height.
9.3.7. Construction
Signs shall be permanently attached or affixed to the ground, building, or other
structure by direct attachment to a rigid wall, frame, or supporting structure.
Portable and/or temporary signs. With the exception of portable and temporary
signs as permitted in this article, signs shall be permanently attached to the
ground, a building, or another structure by direct attachment to a rigid wall,
frame, or structure.
9.3.8. Maintenance Requirements
All signs and all components thereof, including supports, braces, anchors, etc.,
shall be kept in a good state of repair, in compliance with all building and
electrical codes, and in conformance with the requirements of these sign
regulations. Any sign which is determined by the Zoning Administrator as being
insecure, in danger of falling or otherwise endangering the public safety shall be
immediately removed by its owner unless it is repaired and made to otherwise
comply with the requirements of these sign regulations.
9.3.9. District Classifications
9.3.9.1. Where this sections references “residential” uses or districts, it shall
mean the following: Rural Agricultural (RA), Rural Residential (RR),
Suburban Family Residential (SFR1), Suburban Family Residential (SFR2),
Suburban Family Residential (SFR3), Town Residential 1 (TR1), and Town
Residential 2 (TR2).
9.3.9.2. Where this sections references “commercial” uses or districts, it shall
mean the following: Village Commercial (VC), Town Center (TC), Public
and Institutional (PI), Corridor Commercial (CC), Interstate Commercial
(IC), Office Commercial (OC), and Light Industrial (LI).
9.3.10. Number of Signs Allowed
Unless otherwise regulated, each parcel is allowed one (1) free-standing sign,
and one of each attached sign.
9.4. Freestanding Signs
9.4.1. Applicability
9.4.2. The following chart applies to all types of development as stated except for
individual single-family or 2-3 unit building lots, or subdivisions containing fewer
than 30 units.
Sign Type Zoning
District
Max
Area
Max
Height
Min
Height
Additional
Requirements/Description
MRB Group – RG Revision 5.23.23 – Version 2
1. Monument Signs
All
commercial
and multi-
family,
except TC;
32 sq. ft. 10 ft. 3 ft. A sign that is mounted on a
foundation and accompanied
by landscaping.
a. Maximum number: 1 per
street frontage. A second is
allowed if spaced more than
300 linear feet away and
reduced by 50%.
b. Landscaping, not including
grass, shall be required for
all monument signs. Such
landscaping shall equal the
total surface area of the sign
face.
c. Foundation of monument
signs shall be of stucco
coated CMU, brick, or other
similar material.
Industrial or
Office Uses
48 sq. ft. 10 ft. 3 ft.
2. Post and Arm Sign
All
commercial
10 sq. ft. 6 ft. 3 ft. A sign supported by a single
post
3. Sandwich Board Signs
TC, VC A portable sign shaped like an
A-frame with a sign panel on
one or both sides, where the
sign panel is integral to the
structure of the sign
4. Easel Sign
All
commercial
A sign or message board
displayed on a portable, open
frame, such as a tripod
MRB Group – RG Revision 5.23.23 – Version 2
5. Pole Mounted Signs
Interstate
Commercial
1 sq. ft.
per 1’ ft
of linear
frontage,
may not
exceed
100 sq.
ft.
30’ 10’ A sign mounted on a single
pole.
a. Sign thickness not to
exceed 2’
9.5. Attached Signs
9.5.1. Applicability
9.5.2. The following chart applies to all types of developments as stated except for
individual single-family or 2-3 unit building lots, or subdivisions containing fewer
than 30 units
Sign Type Permitted
Location
Max Area Additional Requirements/Description
1. Wall
All
commercial
and multi-
family
10% of area of primary
building frontage of
the first floor.
A sign mounted parallel to or painted
on a building facade or other vertical
building surface.
a. Maximum Number – 1 per street
frontage. Signs on secondary
frontages may be ½ the size of the
primary sign.
b. No sign shall extend above the roof
line
c. No sign shall project from the
façade more than 18”
d. Not permitted for residential uses,
other than multi-family buildings
exceeding 10 units
2. Canopy/Awning
All
commercial
and multi-
family
50% of canopy valance
area
a. Maximum Number:1 per building
frontage or tenant space, per
street frontage
b. Must allow 8 feet clearance
above sidewalk
c. Shall not be placed above 2nd
floor window sill or cornice of
building, whichever is higher
d. May encroach over sidewalk area
no closer than 18 inches from
curb
e. Only the valance area of the
awning/canopy may be used as a
message area. The valance shall be
a maximum of 1fttall with lettering
a maximum of9inches tall. The
valance shall be made of the same
material and shall be the same color
as the awning/canopy.
MRB Group – RG Revision 5.23.23 – Version 2
3. Window/Door
All
commercial
and multi-
family
25% of transparent
areas of windows or
doors
Applied plastic or vinyl cut letters are
prohibited.
No permit is necessary for temporary
promotional signs posted on the
interior side of the glass; these signs
shall count toward the 25% maximum
window coverage.
4. Projecting/Suspended
All
commercial
and multi-
family
8 square feet 1. Maximum Number:1 per building
frontage or tenant space, per
street frontage
2. Must allow 8 feet clearance
above sidewalk
3. May project no more than 4 feet
from building face and no closer
than 18 inches from curb
4. Not permitted for residences
with3 or fewer dwelling units
5. Projecting signs shall not be
higher than the fascia and/or
cornice and shall not extend
above the eave line.
6. For multi-story buildings, sign
brackets shall be mounted no
higher than the sill of the second-
floor window.
*The total area of all attached signs for a business shall be no more than 1.5 times the linear frontage of the building, or in
the case of multi-tenant buildings, than the individual tenant space.
9.6. Other Signs that Require a Zoning Permit
9.6.1. Tenant Directory Signs
9.6.1.1. Applicability: Tenant directory signs listing only the name and address of
the business shall be permitted in multi-building, multi-tenant
professional, office, and/or business centers
9.6.1.2. Maximum Area: 32 square feet in surface area shall be permitted per
street frontage
9.6.1.3. Maximum Height: 10 feet
9.6.1.4. Maximum Number: 1 per lot — lots with more than 1,000 feet of street
frontage and more than one Department of Transportation-approved
driveway or street entrance shall be permitted an additional directory
sign on the condition that such driveways are spaced at least 1,000 feet
apart.
9.6.1.5. Location: Tenant directory signs shall be located within the buildable
area and outside of any required buffer. The tenant directory sign must
be located at least 25 feet from any adjacent right-of-way.
9.6.2. Multi-Tenant Free-Standing Signs
MRB Group – RG Revision 5.23.23 – Version 2
9.6.2.1. Applicability: Multi-Tenant signs are required for multi-building
developments with 5 or more occupiable spaces.
9.6.2.2. Design: The design, material, color, location, and illumination of signage
shall be compatible with the overall design of the development. Multi-
tenant signs shall follow the same regulations as monument signs with
regard to landscaped areas around the foundation of the sign.
9.6.2.3. Size: The size of a multi-tenant size shall not exceed 125 sq. ft. If there
are more than 10 occupiable spaces on one parcel, a 125% increase in
sign area is permitted.
9.6.2.4. Height: The height of such signs shall not exceed 10’.
9.6.2.5. Number Allowed: Only one multi-tenant sign is allowed per
development. No individual tenant free-standing signs are permitted. A
second multi-tenant sign, equaling 50% of the total size of the first, may
be permitted if the property if the following is true:
9.6.2.5.1. The individual street frontage is greater than 500 feet.
9.6.2.5.2. The property is located on a corner or intersection.
9.6.2.5.3. The second sign shall be composed of the same
materials and design as the first.
9.6.3. Residential Neighborhood Identification Signs
9.6.3.1. Applicability: Residential neighborhoods with 10 or more lots.
9.6.3.2. Number Allowed: One per entrance
9.6.3.3. Max Area: 32 square feet
9.6.3.4. Max Height: 8 feet
9.6.4. Directional Signs
9.6.4.1. Applicability: A directional sign has a directional message in symbols or
words and may be a private, unofficial traffic signs, designate private
parking, or be place at a site entrance to warn the public against
trespassing. It may also contain the name of a business on the site,
and/or its address.
9.6.4.2. Permitted Location: All commercial districts
9.6.4.3. Maximum Number: 1 per entrance
9.6.4.4. Maximum Area: 2 square feet
9.6.4.5. Maximum Height: 2.5 Feet; Parking stall signs are allowed to be 5’ in
height
9.6.4.6. Off-Premise Signs: Directional signs that are off-premise are not
permitted.
9.7. Temporary Signs
9.7.1. Types of Temporary Signs
9.7.1.1. Promotional Banners
9.7.1.1.1. Maximum Number: 1 per tenant
MRB Group – RG Revision 5.23.23 – Version 2
9.7.1.1.2. Maximum Area: 30 square feet, with a vertical dimension no
greater than 3 feet.
9.7.1.1.3. Minimum Height: Must be placed a minimum of 7 feet above
sidewalk grade
9.7.1.1.4. Location: Attached to building (must be secured along all 4
sides of banner)
9.7.1.1.5. Time Period: Maximum of 30 days
9.7.1.1.6. Additional Requirements: Application for a permit for
promotional banners may be made only 4 times during any
calendar year with no permits being approved consecutively.
A minimum of 30 days shall expire before an application for a
permit for a promotional banner can be accepted.
9.7.1.2. Construction Signs:
9.7.1.2.1. Maximum Number: 1 per street frontage
9.7.1.2.2. Maximum Area: 32 square feet
9.7.1.2.3. Maximum Height: 6 feet
9.7.1.2.4. Location: Minimum of 10 feet from the street right of way.
9.7.1.2.5. Time Period: The sign permit shall be valid for the duration of
the construction period.
9.7.1.3. Grand Opening Signs
9.7.1.3.1. Location: A minimum of 3 feet from the right-of-way; 18
inches from the right-of-way in the Historic District.
9.7.1.3.2. Maximum Number: Up to 3 types of signs are permitted for
grand openings.
9.7.1.3.3. Type: Free-standing and attached signs are permitted at the
discretion of the administrator.
9.7.1.3.4. Time Period: A maximum of 30 days.
9.7.1.3.5. Special Event Signs: Governmental, nonprofit, school, church
or civic club-sponsored signs related to special events shall
meet the following standards:
9.7.1.3.5.1. Signs shall be permitted 14 days prior to a
function and shall be removed within 3 days after
the function.
9.7.1.3.5.2. Signs shall be located on private property.
9.7.2. Exempt Signs
9.7.2.1. No zoning permit is required within the following section:
9.7.2.1.1. Government Signs including signs required by any law, order
or governmental regulation.
9.7.2.1.2. Property Address Signs
9.7.2.1.3. Private Residence Signs
MRB Group – RG Revision 5.23.23 – Version 2
9.7.2.1.3.1. One personal identification sign not exceeding 2
square feet in area
9.7.2.1.3.2. One non-illuminated "For Sale" or "For Rent" sign
not exceeding 6 square feet in area.
9.7.2.1.4. Historical markers, historical monuments or signs as
recognized by local, state, or federal authorities.
9.7.2.1.5. Signs denoting the location of underground utilities
9.7.2.1.6. Holiday decorations
9.7.2.1.7. Signs on interior windows that are not permanently affixed to
the glass and do not exceed 25% of the gross glass area.
9.7.2.1.8. Temporary special event signs and banners for religious,
charitable, civic, fraternal, or similar non-profit or not-for-
profit organizations provided that:
9.7.2.1.8.1. Signs shall be erected no sooner than thirty (30)
days prior and removed no later than five (5) days
after the event;
9.7.2.1.8.2. No such sign shall exceed thirty-two (32) square
feet;
9.7.2.1.8.3. No such sign shall be illuminated; and
9.7.2.1.8.4. All such signs shall be located off the street right-
of-way, unless otherwise granted permission for
such location by the Town of Chapin or SCDOT. In
no case may any such sign impede the view or
travel of any motorists or pedestrians or be
attached to any structure within the right-of-way
(government signs, telephone poles, etc.)
9.7.2.1.9. "Warning", "No Trespassing" and similar informational signs.
9.7.2.1.10. Permanent municipal, school, recreational and civic club
sponsored signs, schedule of events, rules and regulations
signs. Such signs shall not include identification signs.
9.7.2.1.11. Any sign inside a building and not intended to be viewed
from the exterior.
9.7.2.1.12. On residentially zoned lots, one unlighted freestanding sign
not more than three (3) square feet in area and not more
than 4 feet in height from the ground to the top of the sign.
The sign may be used to advertise a home occupation,
garage sale, temporary construction or as a “for sale/rent”
sign, etc. The sign shall not advertise any commercial
enterprise not conducted on the same zone lot.
9.7.2.1.13. Memorial signs, plaques or grave markers which are
noncommercial in nature.
9.7.2.1.14. Flags, pennants, insignia, or religious symbols of any
government, non-profit or not-for- profit organization when
MRB Group – RG Revision 5.23.23 – Version 2
not displayed in connection with a commercial promotion or
as an advertising device.
9.7.2.1.15. Real Estate Signs advertising sale or lease of the premises
subject to the following standards:
9.7.2.1.15.1. One on-site sign per 1,000 ft of street frontage
is permitted. The maximum size shall be 6
square feet, and the maximum height shall be
4.5 feet. For Light Industrial (LI) and Office
Commercial (OC), the size may be increased to
20 sq. ft. with a height not to exceed 6’
9.7.2.1.15.2. The signs shall be removed once the property is
occupied by the new tenant, or when the
property is sold by transfer of title to the same
9.7.2.1.15.3. Special event signs such as for open houses,
agent tours or events, grand openings, and
similar, shall abide by the same rules as
described in 9.8.8 addressing the use of
Temporary signage.
9.7.2.2. Political Signs
9.7.2.2.1. Each sign shall not exceed ten (10) square feet in area in
residential districts and thirty-six (36) square feet in
commercial and manufacturing districts;
9.7.2.2.2. No sign shall be placed in any right-of-way, on any telephone
pole or street sign, trees, or on any public property; and
9.7.2.2.3. Signs are permitted to be erected within sixty (60) days prior
to an election and must be removed within 7 days after an
election.
9.7.3. Prohibited Signs
The following signs are prohibited:
9.7.3.1. Off-premise signs, with the exception of flags of a sovereign nation, and
banners erected by the city, county, or state government.
9.7.3.2. Signs within the public rights-of-way, except those posted by a public
agency
9.7.3.3. In any manner or place that constitutes a hazard to pedestrian or
vehicular traffic
9.7.3.4. In a manner that obstructs free ingress to or egress from a required
door, window, fire escape, or other required exit.
9.7.3.5. Off-premise commercial signage affixed to a private residence or
dwelling, or displayed upon the grounds thereof.
9.7.3.6. Attached to or painted onto the following:
9.7.3.6.1. Trees, rocks or other natural features
9.7.3.6.2. Fence posts, telephone or utility poles
MRB Group – RG Revision 5.23.23 – Version 2
9.7.3.6.3. Roofs signs, or attached signs that project above the building
height.
9.7.3.7. Moving, Flashing, or Audible Signs
9.7.3.7.1. Signs that move by any means regardless of whether they
contain written messages
9.7.3.7.2. Signs set in motion by movement of the atmosphere or by
mechanical, electrical, or other means, including, but not
limited to: flags, adversails, feathers, pennants, posters,
propellers, discs, ribbons, balloons, streamers, strings of light
bulbs, and spinners.
9.7.3.7.3. Flashing signs or devices displaying intermittent lights or lights
of changing intensity
9.7.3.7.4. Signs that emit audible sound or visible matter.
9.7.3.8. Movable or Towed Signs: Signs constructed to be used as a conveyance
upon public streets, and usually parked in public places or private
property primarily for the purpose of public display.
9.7.3.8.1. Exception: Commercial vehicles, including standard passenger
vehicles, that are fully operable may bear a permanently-
adhered commercial message. They must be parked in a
typical parking space and may not be located on landscaped
areas or at angles to the street so as to increase visibility.
9.7.3.9. Inflatable signs [including inflated balloons having a diameter of greater
than two (2) feet for special events and grand openings, used in
conjunction with a commercial building, project, or enterprise are
permitted for a period not to exceed fourteen (14) days
9.7.3.10. Sign Content Limitations
9.7.3.10.1. Signs copying or imitating official government signs, or that
purport to have official government status
9.7.3.10.2. Any sign and/or sign structure that obstructs the view of,
may be confused with, or purports to be a governmental or
traffic direction/safety sign.
9.7.3.10.3. Signs containing statements, words, or pictures of obscene,
pornographic, or immoral character that is not considered
protected speech
9.7.3.11. Impermanent and Unsubstantial Sign Types: Signs that are
constructed of impermanent and unsubstantial materials including
but not limited to inflatable signs, snipe signs, and feather
signs/banners.
9.7.3.12. Abandoned or Deteriorated Signs or Businesses:
9.7.3.12.1. Sign structures no longer containing signs.
9.7.3.12.2. Signs made structurally sound by unsightly bracing.
9.7.3.12.3. Abandoned or dilapidated sign.
9.7.3.12.4. Signs referencing businesses which have been out of
business for more than 30 days.
MRB Group – RG Revision 5.23.23 – Version 2
9.7.3.13. Billboards: Billboards are prohibited.
9.8. Violations
9.8.1. Impoundment of Signs
9.8.1.1. If any sign requiring a permit is erected without a permit, or if any sign is
erected in violation of these regulations, the Zoning Administrator shall
have the authority to give the owner thereof written notice of such
violation. The notice shall include a brief statement of the particulars in
which the violation is to be remedied. If the sign has been permitted,
notice to the person receiving the permit shall be sufficient. If the sign
owner cannot be found, the duty to perform corrections or removal of
the sign will be upon the property owner on whose property the sign is
located.
9.8.1.2. If within ten (10) days the owner of the sign fails to contact the Zoning
Administrator, bring the sign into conformance with these regulations,
and obtain a sign permit, the Building Official shall have the authority to
have the sign removed and impounded without further notice and the
cost of removal shall constitute a lien against the property on which the
sign is located. The Town shall not be liable for any damage to the sign
or property as a result of such removal.
9.8.1.3. The Zoning Administrator shall have the authority to remove and
impound, without notice to the owners thereof, any signs placed within
any street right-of-way, signs attached to trees, rocks or other natural
features, and signs attached to telephone and utility poles.
9.8.1.4. If the impounded sign is not claimed within 30 days, then the
administrator shall have authority to dispose of such sign.
Source: Town of Chapin website. First collected Oct 14, 2026.