RecordWell Data

Board of Architectural Design and Historic Review — Agenda Packet

City of Spartanburg · Spartanburg County · Boards and Commissions · meeting of Feb 12, 2026 · Agenda packets

Open the original document More from City of Spartanburg

Text

Extracted automatically from the original. Tables and formatting may not survive; the original document is authoritative.

The City of Spartanburg Board of Architectural Design & Historic Review City of Spartanburg | Board of Architectural Design & Historic Review 1 AGENDA February 12, 2026, at 5:30 P.M. Dr. TK Gregg Community Center 650 Howard Street – Spartanburg, SC 29303 (Please Note: Items as they appear on the Docket may or may not be considered in the order as they are presented. The Chairman will announce any changes after the roll call) I. Call To Order. II. Roll Call. III. Freedom of Information Act Compliance – Public notification of the City of Spartanburg’s Board of Architectural Design & Historic Review meeting has been published, posted and mailed in compliance with the Freedom of Information Act and the requirements of the City of Spartanburg’s Zoning Ordinance. IV. Rules and Procedures for Meeting Conduct. V. Approval of Agenda. VI. Disposition of Minutes from the December 11, 2025, Meeting. VII. Old Business: None. VIII. New Business: 1. COA: 26-004-00001: Certificate of Appropriateness for Major Works — 133 Phifer Drive (TMS # 7-08-16-012.00) in the Beaumont Mills Historic District. The applicant is seeking approval to install new windows and HardiePlank siding. The property is located in the R-6 (General Residential) zoning district. Owner: Cheri Lindsey / Contractor: Taylor Coastal Construction IX. Staff Announcements: We are exploring the possibility of offering virtual board orientations and continuing education sessions. More details will be shared soon. X. Adjournment. For more information, please contact the City of Spartanburg Planning Department at planning@cityofspartanburg.org or call (864) 596-2068. . HARB – Meeting Minutes – 2025-12-11 Page 1 of 5 Meeting Minutes of the Board of Architectural Design and Historic Review Thursday, December 11, 2025, at 5:30 PM Spartanburg County Council Chambers The City of Spartanburg Board of Architectural Design and Historic Review (HARB ) met in County Council Chambers on Thursday, December 11, 2025, at 5:30 PM with the following members in attendance: Sylvelie Franke, Brett Avery, Dave Williams, Kenneth Brown, Julie Gilmore, Rod McCants, and Bill Michels. Representing the Planning Department - Fredalyn Frasier, Planning Director, Dominick Calace, Planner I. Roll Call: Mr. Michels: Bill Michels Ms. Gilmore: Julie Gilmore Dr. Avery: Brett Avery Mr. Brown: Kenneth Brown Mr. McCants: Rod McCants (Late Arrival) Mr. Williams: Dave Williams Ms. Franke: Sylvelie Franke Mr. Michels: Freedom of Information Act Compliance – Public notification of the City of Spartanburg Board of Architectural Design and Historic Review (HARB ) this meeting has been published, posted and mailed in compliance with the Freedom of Information Act and the requirements of the City of Spartanburg Zoning Ordinance. Approval of Agenda: A motion was made by Mr. Brown seconded by Dr. Avery to approve the agenda. The motion was approved with a vote of 7-0. Approval of Meeting Minutes from November 13, 2025. A motion was made by Dr. Avery, seconded by Mr. Brown to approve the meeting minutes as amended. The motion was approved with a vote of 7-0. Old Business: None. New Business: COA: 25-004-00072: Certificate of Appropriateness for Major Works — 118 Phifer Drive (TMS # 7-08- 15-259.00) in the Beaumont Mills Historic District. The applicant is seeking approval to install new vinyl windows. The property is located in the R-6 (General Residential) zoning district. Owner: Tyler & Katie Helms / Contractor: Golden Key Construction Project Description and History The project site is located on an approximately 9,700 square foot lot in the Beaumont Mills Historic District on the south side of Phifer Dr ive. The residential structure was constructed in 19 41. The architectural style designated by the Beaumont Mill Design Guidelines is House Type 13 – Gable on Hip Cottage. The Applicant is seeking approval to replace all of the windows on the structure. The Applicant has stated that the existing windows have broken panes, do not close all the way, and are inefficient, leading to high energy bills. The existing windows on the structure are six-over-six single-pane wood windows. The windows will be replaced with six-over-six simulated divided lite vinyl windows. Photos of both the interior and exterior of the windows are included, as well as the specifications for the proposed replacement units. The Applicant has noted that replacing the existing windows with new wood units would require custom fabrication and would be significantly more expensive than vinyl replacements. According to the Applicant, HARB – Meeting Minutes – 2025-12-11 Page 2 of 5 vinyl windows are priced between $500–$900 per unit, while new custom wood windows begin at approximately $1,200 per unit. The Applicant states that this cost difference affects the feasibility of replacing their windows. Analysis Zoning Ordinance and Historic Design Manual Consistency The design guidelines are outlined in the Beaumont Mills Design Guidelines for the City of Spartanburg Historic District Preservation Principles and Approaches . The purpose of the guidelines is to provide property owners with guidance for the preservation and protection of historic and architecturally valuable districts and sites in the City. The project is also subject to Section 510 of the City ’s Zoning Ordinance, Historic Preservation. This section allows the Board to review applications involving historic structures and districts and issue a Certificate of Appropriateness subject to the standards listed in the Ordinance. Section 510.6 of the City of Spartanburg Zoning Ordinance list standards for reviewing a Certificate of Appropriateness. Specifically, Section 510.6 (C)(2) states that in reviewing applications for new construction or alteration, the Board shall consider the U.S. Secretary of the Interior’s Standards for Rehabilitation and the five criteria listed in the findings. Beaumont Mills Design Guidelines Findings Certificate of Appropriateness, Section 510.6 (C) a. The character and appropriateness of the design Section 8.1.4 Windows of the Beaumont Mill Design Guidelines state s, “ Windows are another significant character defining feature of any home. Wood windows were constructed so that individual pieces could be taken apart and repaired as needed. Therefore, many original windows could be repaired for much less than replacing a window. If it’s determined that the windows are in such deteriorated condition that they must be replaced, you should select a new window with extreme care. Make sure the following details should be compatible when selecting a new window: Size of window, Shape and size of sash, Window pane size and configuration, Muntin and Mullion profile shape, and Location of meeting rail. Wood and aluminum clad wood windows are the most appropriate replacement materials. Other window materials will be evaluated by the HARB.” • The proposed replacement windows maintain the six-over-six configuration and size of the original windows. The proposed material (vinyl) differs from the original wood windows and must be evaluated by the HARB. b. The scale of the buildings • The replacement of windows will not affect the scale of the buildings. c. The texture and materials • The proposed replacement windows are vinyl, which is different in material and texture from the existing wood windows. The window openings and configuration will remain the same. d. The relationship of such elements to similar features of structures in the immediate surroundings – • Properties in the immediate surroundings of the project site appear to have a combination of wood and vinyl windows. The properties to the left and right both have vinyl windows. Of the three properties across the street, two have vinyl windows, and one has wood windows. e. If the property is in a Historic District, the extent to which the alteration or construction would be harmonious with the Historic District – • The Design Guidelines require replacement windows to be compatible with the originals in material, size, and design. While the proposed windows retain the size and six -over-six configuration, the vinyl material must be evaluated for harmony with the historic district. Staff Comments HARB – Meeting Minutes – 2025-12-11 Page 3 of 5 Staff acknowledge the Applicant’s stated cost difference between custom wood windows and the proposed vinyl replacements. If the Board determines that the proposed vinyl windows match the size of the existing openings, retain the six-over-six configuration, and provide an acceptable sash/muntin profile, and meeting-rail alignment consistent with the Design Guidelines, approval of the replacement may be appropriate. Staff Recommendation The property is classified as a contributing structure, and staff recommends that vinyl windows not be used for replacement of windows visible from the street. • Replacement windows should maintain the original openings, proportions, muntin patterns, and trim profiles to preserve the historic integrity of the façade and the district’s character. • Historically appropriate alternatives such as wood, fiberglass, or composite/wood-clad windows. • The City may have funding or grant programs available to assist property owners experiencing financial hardship in meeting these requirements. Applicant: Victor Borisik (Golden Key Construction) Public Speakers: Melissa Scoeffel Joseph Parks Discussion: The board discussed the window material request with an emphasis on visual compatibility and long-term durability. While several members expressed concern about diverging from original materials, they agreed that in this case, composite for the front-facing windows and vinyl for the side and rear could achieve a balanced outcome. The applicant was responsive, and staff confirmed they would review the final selections to ensure consistency with the district. A motion was made by Mr. Brown and seconded by Dr. Avery to approve vinyl windows on the side and rear elevations of the home. The three front-facing windows shall be wood-clad, fiberglass, or composite material, subject to staff review for compliance prior to installation. The motion passed by a vote of 5 in favor, 1 opposed, and 1 abstained. COA: 25-004-00071: Certificate of Appropriateness for Major Works — 189 S Hampton Drive (TMS # 7-16-02-276.00) in the Hampton Heights Historic District. The applicant is seeking approval to install new vinyl windows. The property is located in the R-8 SFD (Single Family Residential) zoning district. Owner: Jessica Fenn / Contractor: Scott Doughman, Window Nation Project Description and History The project site is located on an approximately 22,000 square foot lot in the Hampton Heights Historic District on the southeast corner of S Hampton Drive and Peronneau Street. The residential structure was constructed in 1987 and does not reflect a historic architectural style. The home is considered a non-contributing structure within the historic district. The applicant is seeking approval to replace all of the windows on the structure. According to the applicant, the existing windows are inefficient, allowing cold air into the home in winter and hot air in summer. The existing windows are one-over-one single-pane wood windows. The applicant proposes replacing them with one-over- one double-pane vinyl windows. Photos of both the interior and exterior windows, as well as product specifications, are included in the application materials. Analysis Zoning Ordinance and Historic Design Manual Consistency The design guidelines are outlined in the Hampton Heights Design Guidelines for the City of Spartanburg Historic District Preservation Principles and Approaches. The purpose of the guidelines is to provide property owners with guidance for the preservation and protection of historic and architecturally valuable districts and sites in the City. HARB – Meeting Minutes – 2025-12-11 Page 4 of 5 The project is also subject to Section 510 of the City ’s Zoning Ordinance, Historic Preservation. This section allows the Board to review applications involving historic structures and districts and issue a Certificate of Appropriateness subject to the standards listed in the Ordinance. Section 510.6 of the City of Spartanburg Zoning Ordinance list standards for reviewing a Certificate of Appropriateness. Specifically, Section 510.6 (C)(2) states that in reviewing applications for new construction or alteration, the Board shall consider the U.S. Secretary of the Interior’s Standards for Rehabilitation and the five criteria listed in the findings. Hampton Heights Design Guidelines Findings Certificate of Appropriateness, Section 510.6 (C) a. The character and appropriateness of the design Section 8.1.4 Windows of the Hampton Heights Design Guidelines state s, “Windows are very important in creating rhythm on a house and also play a role in the directional emphasis and scale of buildings. Highly decorative windows with distinctive shapes or glazing patterns are always character -defining features of buildings. Guideline: Existing windows, including window sash, glass, lintels, sills, frames, molding, shutters, and all hardware shall be retained and repaired through routine maintenance whenever possible. When deteriorated elements must be replaced, new materials shall be compatible with orig inal materials in terms of material, design, and hardware. If it is necessary to replace an entire window, the replacement shall be sized to the original opening and shall duplicate all proportions and configurations of the original window.” • The proposed replacement windows maintain the existing one -over-one configuration and size of the original windows. The proposed material (vinyl) differs from the existing wood windows. b. The scale of the buildings • The replacement of windows will not affect the scale of the buildings. c. The texture and materials • The proposed replacement windows are vinyl, which differs in material and texture from the existing wood windows. The window openings and configuration will remain the same. d. The relationship of such elements to similar features of structures in the immediate surroundings – • Properties in the immediate surroundings of the project site appear to have wood windows. e. If the property is in a Historic District, the extent to which the alteration or construction would be harmonious with the Historic District – • The Design Guidelines require replacement windows to be compatible with the originals in material, size, and design. The vinyl material differs from the original wood windows, while the size and one - over-one design are retained. Staff Recommendation Staff recommends Applicant: Joseph Parks Public Speakers: Lukas Hauser Discussion: The board emphasized the importance of maintaining the overall character of the neighborhood. Members noted that while vinyl windows may be acceptable for the rear and side elevations due to limited visibility, the front-facing windows should meet a higher standard to preserve the streetscape. There was general agreement HARB – Meeting Minutes – 2025-12-11 Page 5 of 5 to allow vinyl in non-visible areas, but require composite, wood, or clad materials for any windows facing the public right of way. The board aimed to strike a balance between practical upgrades and visual integrity, referencing prior case language to guide consistency. A motion was made by Dr. Avery, seconded by Mr. Brown, to allow vinyl windows and sliders at the rear as proposed, and to require composite, wood, or clad windows on the front elevation, subject to staff approval prior to installation with a vote of 7 to 0. Staff Announcements: Staff shared updates on continuing education for 2026, with plans to offer ACOG sessions virtually or host them locally at the Dr. TK Gregg Community Center to support CEU completion. All 2026 HARB meetings will also be held at this location, 650 Howard Street, in the main community room. No applications were received for the January meeting. Members will receive reminders before the February session. Code Enforcement continues to follow up on housing compliance. At 232 Hydrick Street, final approvals were granted after board-requested changes were confirmed, including a full brick foundation and smooth siding. The applicant is expected to apply for permits soon. The meeting was adjourned at 6:35 PM. ______________________________ Bill Michels, Chairman Planning Department PO Box 1749 • Spartanburg, SC 29304 • Phone: (864) 596-2068 • email: planning@cityofspartanburg.org website: www.cityofspartanburg.org February 5, 2026 TO: The Board of Architectural Design and Historic Review RE: Certificate of Appropriateness for Major Works Address: 133 Phifer Dr (TMS: 7-08-16-012.00) Historic District: Beaumont Mills Historic District Zoning: R-6 (General Residential District) Owner/Applicant: Cheri Lindsey Contractor: Taylor Coastal Construction Request: The Applicant is seeking approval to install new aluminum clad windows on the front facing windows and vinyl on the rear and sides. The applicant also proposes replacing the removed vinyl siding with fiber cement (HardiePlank) lap siding. ______________________________________________________________________________ Project Description and History The project site is located on an approximately 6,800 square foot lot in the Beaumont Mills Historic District on the north side of Phifer Dr ive. The residential structure was constructed in 19 42 and is classified as a contributing structure. The architectural style designated by the Beaumont Mill Design Guidelines is House Type 15 – End Gable with Gable Front Porch. Windows The applicant is seeking approval to replace all windows on the structure. The existing windows are primarily vinyl windows that were installed prior to the adoption of the Beaumont Mill Design Guidelines. One original wood window remains on the front elev ation and is in poor condition. The home has recently undergone significant repairs related to termite damage. The proposed window replacement includes installing simulated divided lite aluminum-clad windows on the front elevation, consisting of one eight -over-eight window and two four -over-four windows, matching the historic configuration (three windows total) . Windows on the side and rear elevations will be replaced with six-over-six simulated divided lite vinyl windows. Specifications for the proposed replacement windows have been submitted with the application. The applicant has worked collaboratively with the Planning Department to identify a cost -effective approach that improves compatibility with the historic character of the structure. The aluminum-clad windows on the front elevation better reflect historic w indow detailing, while the vinyl windows on the side and rear elevations maintain a consistent appearance and represent an improvement over the existing one-over-one vinyl windows previously installed on the structure. Siding All existing siding has been removed from the structure, as shown in the submitted site photos. Termite damage had been previously identified on the home, and the existing vinyl siding was removed in order to access and repair the damaged areas. The vinyl siding was also in poor condition and deteriorating at the time of removal. Historically, the structure was clad in asbestos -cement siding. The Applicant proposes to re-side the structure with James Hardie Straight Fiber Cement Smooth Lap Siding, utilizing 8.25 -inch-wide boards with an approximate 7 -inch exposure. This exposure more closely reflects the historic asbestos-cement siding originally present on the structure. Analysis Zoning Ordinance and Historic Design Manual Consistency The design guidelines are outlined in the Beaumont Mills Design Guidelines for the City of Spartanburg Historic District Preservation Principles and Approaches . The purpose of the guidelines is to provide property owners with guidance for the preservation and protection of historic and architecturally valuable districts and sites in the City. The project is also subject to Section 510 of the City ’s Zoning Ordinance, Historic Preservation. This section allows the Board to review applications involving historic structures and districts and issue a Certificate of Appropriateness subject to the standards listed in the Ordinance. Section 510.6 of the City of Spartanburg Zoning Ordinance list standards for reviewing a Certificate of Appropriateness. Specifically, Section 510.6 (C)(2) states that in reviewing applications for new construction or alteration, the Board shall consider the U.S. Secretary of the Interior’s Standards for Rehabilitation and the five criteria listed in the findings. Beaumont Mills Design Guidelines Findings - Windows Certificate of Appropriateness, Section 510.6 (C) a. The character and appropriateness of the design Section 3.7.2 Windows of the Beaumont Mill Design Guidelines state s, “ Windows are another significant character defining feature of any home. Wood windows were constructed so that individual pieces could be taken apart and repaired as needed. Therefore, many original windows could be repaired for much less than replacing a window. If it’s determined that the windows are in such deteriorated condition that they must be replaced, you should select a new window with extreme care. Make sure the following details should be compatible when selecting a new window: Size of window, S hape and size of sash, Window pane size and configuration, Muntin and Mullion profile shape, and Location of meeting rail . Wood and aluminum clad wood windows are the most appropriate replacement materials. Other window materials will be evaluated by the HARB.” • The proposed replacement windows restore the historic configuration and size of the original windows. The aluminum-clad wood windows proposed on the front elevation are an approved replacement material per the Design Guidelines. Vinyl windows proposed on the side and rear elevations require Board review. b. The scale of the buildings • The replacement of windows will not affect the scale of the buildings. c. The texture and materials • The aluminum-clad wood windows proposed on the front façade are consistent with the Design Guidelines. The vinyl windows proposed on the side and rear elevations differ from the original material and require Board evaluation. d. The relationship of such elements to similar features of structures in the immediate surroundings – • Properties in the immediate surroundings of the project site appear to have a combination of wood and vinyl windows. The homes directly adjacent to the subject property have vinyl windows. Of the three properties immediately across the street, two have vinyl windows and one has wood windows. e. If the property is in a Historic District, the extent to which the alteration or construction would be harmonious with the Historic District – • The Design Guidelines require replacement windows to be compatible with original windows in material, size, and design. While the proposed windows retain appropriate size and configuration, the vinyl material on the side and rear elevations must be evaluated by the Board for compatibility with the historic district. Findings - Siding Certificate of Appropriateness, Section 510.6 (C) a. The character and appropriateness of the design Section 3.7.6 Exterior Siding of the Beaumont Mill Design Guidelines states, “ Most of the homes in Beaumont were originally wood siding. If this material still exists on the home, it should be retained. Many homes in the area have aluminum or vinyl siding added to them. Some homes have asbestos siding which is original to their desi gn and some asbestos siding was added to earlier homes in the 1950’s. Details of the original home have been lost due to the additions of these materials. Artificial siding can trap moisture underneath and decay the original wood. Therefore, homes that do not have these materials on them should not consider artificial materials as a replacement to the damaged wood. Repair is the only option. Should it become necessary to replace the siding, then the new boards should match the existing boards in width and any characteristics, such as corner boards. If more than 50% of the siding will be replaced, then the type of siding must match the historic style of siding. Appropriate new material should be: - Wood - Cement Fiberboard” • The proposed replacement siding is James Hardie Straight Fiber Cement Smooth Lap Siding 8.25in. This board will have a final exposure of 7 -inches. The design guidelines recommend cement fiberboard as an approved material. b. The scale of the buildings • The replacement of siding will not affect the scale of the buildings. c. The texture and materials • The proposed replacement siding is cement fiberboard. This material is recommended by the Design Guidelines as an approved material. d. The relationship of such elements to similar features of structures in the immediate surroundings – • Properties in the immediate surroundings of the project site appear to have a combination of wood, vinyl, and asbestos siding. The properties directly adjacent to the subject property have wood shingle siding and vinyl siding. All three properties immediately across the street have vinyl siding. e. If the property is in a Historic District, the extent to which the alteration or construction would be harmonious with the Historic District – • The Design Guidelines require replacement siding to match the historic style of siding. In this case, fiber cement board would be the most appropriate replacement material for siding replacement to match the original asbestos siding. Staff Comments Staff acknowledge the Applicant’s stated cost difference between custom wood or aluminum clad windows and the proposed vinyl replacements. If the Board determines that the vinyl windows proposed for the side and rear elevations maintain the original window openings, retain the six-over- six configuration, and provide acceptable sash and muntin profiles with appropriate meeting-rail alignment, approval of the vinyl windows may be appropriate. Staff Recommendation - Approval The subject property is classified as a contributing structure within the Beaumont Mills Historic District. Based on the findings above, staff recommends approval of the proposed window replacement and siding installation. • Staff supports the installation of aluminum-clad simulated divided lite windows on the front (street-facing) elevation. This material is consistent with the Beaumont Mills Design Guidelines and maintains the historic character of the primary façade. • For the side and rear elevations, staff acknowledges the Applicant’s cost considerations and finds that vinyl simulated divided lite windows may be appropriate provided that the Board determines the windows meet the following criteria: o Maintain the original window openings, proportions, and configuration o Retain the six-over-six muntin pattern o Provide an acceptable sash, muntin profile, and meeting-rail alignment consistent with the Design Guidelines • Staff finds the proposed fiber cement (HardiePlank) lap siding with a 7-inch exposure to be appropriate and consistent with the historic asbestos-cement siding and recommends approval as proposed. Submitted by: Dominick Calace Planner I City of Spartanburg Planning Department Attachments: Conditions of Approval Site Map Zoning Map Site Photos Application and Materials CONDITIONS OF APPROVAL FOR THE PROJECT ON PROPERTY AT: 133 Phifer Dr (TMS: 7-08-16-012.00) – Beaumont Mills Historic District Owner/Applicant: Cheri Lindsey Contractor: Taylor Coastal Construction 1. If one or more of the following conditions is not met with respect to all its terms, then this approval may be revoked. 2. All plans for future construction which are not covered by this review shall be submitted to the City Planning Department for review and approval. 3. Major modifications to plans or exceptions to completion may be granted only by the City authority which approved the project. 4. This permit shall be exercised within six months of the date of final approval, or it shall become null and void. Extensions may be granted with the permission of the Board. 5. A building permit shall be obtained from the Building Department prior to commencement of work. 6. The development of the site shall be in substantial accordance with the approved plans submitted and on file in the Spartanburg City Planning Department. Major modifications to plans or exceptions to completion may be granted only by the City authority whi ch approved the project. Site Map – 133 Phifer Dr Zoning Map – 133 Phifer Dr Site Photos – 133 Phifer Dr Properties to the Left and Right Properties Across the Street [ What can we help you find? Q Shop All Appliances Bathroom Building Supplies Doors & Windows Flooring Lawn & Garden Lighting Tools Plumbing Outdoor Valentine's Day CJ Spartanburg Lowe's 9 PM v � 29301 v wooi9 Prices, Promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and ser are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer one correct any errors, inaccuracies or omissions including after an order has been submitted. Building Supplies / Siding & Stone Veneer / Fiber Cement Siding & Accessories / Fiber Cement Siding 8 Viewed 01/29/2026 More Re ( ++ Ask Mylow ) Siding Specifications SHIP TO:BILL TO: Phone Email Phone Fax 843-795-0150 1911 MAYBANK HWY - CHARLESTON, SC 29412 100-1 Rough Opening: Overall Unit Size: Room Location: H3 Aluminum Clad Double Hung Windows 2.0, Rectangle, 45.5 x 55.5, Operating [DIMENSIONS], Frame Width = 45.5, Frame Height = 55.5 [UNIT TYPE], Complete Unit, 46 X, 56, Sash Split = 50/50, Operating, CoreGuard Plus [FRAME], White 001, AAMA 2604, Pine, Primed Interior, White, Visible Interior Vinyl Profile Color = Beige, Frame Jamb Style = Flush [SASH PANEL], White 001, AAMA 2604, Standard, Primed Interior, White, Ship Sash Separate = No, W/S = Black [GLASS], Dual Insulated, Low-E 366, Argon Gas, Black Warm Edge Spacer, Glass Width = 40.375, Glass Height = 24.8125 [GRILLES], Grille App = Simulated Divided Lite, Grille Pattern = Equal, Grille Profile = Traditional, Bar Width = 5/8", Exterior Grille Color = White 001, Wood Grille Species = Pine, Interior Grille Finish = Primed Interior, Interior Grille Primed Color = White, Clad Grille Finish = 2604, Shadow Bar = Yes, Shadow Bar Color = Dark Bronze Anodized, Division = Custom, 4W, 2H [HARDWARE], Applied, Standard, Standard Lock, Hdwr Color = White, 2-Locks, Jamb Liner Type = Concealed, [SCREENS], Full Screen Applied, FlexScreen, View Clear Mesh, Scrn Wth = 43.5, Scrn Ht. = 53.656 [WRAPPING], 4 9/16"Jamb, Nail Fin = Integral Rigid Vinyl Nailing Fin, Aluminum Drip Cap Applied [PERFORMANCE], U-Factor = 0.29, SHGC = 0.19, CR = 55, VT = 0.43, AI = <0.30/<1.5, CPD = SIE-N-135-04749-00004, Can ER = 15, W m 2k = 1.65, Performance Grade = PG50 45.5" X 55.5" None Assigned LINE # DESCRIPTION U/M 1 QTY EXTENDEDNET PRICE $1,196.99$1,196.99EA None Assigned LINE TYPE WindowAndDoor PK- 379 46" X 56" QUOTE # 2015646 JASON KELLER / CASH107 / JCAMP QUOTE NAME PROJECT JASON KELLER / CASH107 / JCAMP JOB NAMEPO # CUSTOMER PO # 4 Of 1 Page* All drawings are viewed from exterior of window. 1/21/2026CQWPNL Aluminum Clad Window Specs QUOTE # 2015646 JASON KELLER / CASH107 / JCAMP QUOTE NAME PROJECT JASON KELLER / CASH107 / JCAMP JOB NAMEPO # CUSTOMER PO # 200-1 Rough Opening: Overall Unit Size: Room Location: H3 Aluminum Clad Double Hung Windows 2.0, Rectangle, 27.5 x 55.5, Operating [DIMENSIONS], Frame Width = 27.5, Frame Height = 55.5 [UNIT TYPE], Complete Unit, 28 X, 56, Sash Split = 50/50, Operating, CoreGuard Plus [FRAME], White 001, AAMA 2604, Pine, Primed Interior, White, Visible Interior Vinyl Profile Color = Beige, Frame Jamb Style = Flush [SASH PANEL], White 001, AAMA 2604, Standard, Primed Interior, White, Ship Sash Separate = No, W/S = Black [GLASS], Dual Insulated, Low-E 366, Argon Gas, Black Warm Edge Spacer, Glass Width = 22.375, Glass Height = 24.8125 [GRILLES], Grille App = Simulated Divided Lite, Grille Pattern = Equal, Grille Profile = Traditional, Bar Width = 5/8", Exterior Grille Color = White 001, Wood Grille Species = Pine, Interior Grille Finish = Primed Interior, Interior Grille Primed Color = White, Clad Grille Finish = 2604, Shadow Bar = Yes, Shadow Bar Color = Dark Bronze Anodized, Division = Custom, 2W, 2H [HARDWARE], Applied, Standard, Standard Lock, Hdwr Color = White, 2-Locks, Jamb Liner Type = Concealed, [SCREENS], Full Screen Applied, FlexScreen, View Clear Mesh, Scrn Wth = 25.5, Scrn Ht. = 53.656 [WRAPPING], 4 9/16"Jamb, Nail Fin = Integral Rigid Vinyl Nailing Fin, Aluminum Drip Cap Applied [PERFORMANCE], U-Factor = 0.29, SHGC = 0.19, CR = 55, VT = 0.43, AI = <0.30/<1.5, CPD = SIE-N-135-04749-00004, Can ER = 15, W m 2k = 1.65, Performance Grade = PG50 27.5" X 55.5" None Assigned LINE # DESCRIPTION U/M 2 QTY EXTENDEDNET PRICE $1,672.03$836.01EA None Assigned LINE TYPE WindowAndDoor PK- 379 28" X 56" 4Of2Page* All drawings are viewed from exterior of window. 1/21/2026CQWPNL QUOTE # 2015646 JASON KELLER / CASH107 / JCAMP QUOTE NAME PROJECT JASON KELLER / CASH107 / JCAMP JOB NAMEPO # CUSTOMER PO # Notes: SUB-TOTAL: LABOR: FREIGHT: SALES TAX: TOTAL: $258.21 $3,127.22 $2,869.01 $0.00 $0.00 SALESPERSONPRINTED BY BID BY jegoodman Order Notes Delivery Notes Dealer Disclaimer: ACCEPTANCE All drawings depict windows and doors as they are viewed from the exterior side of the building. Oversized units and certain mulled/stacked configurations have not been tested and, therefore, have no performance grade (PG) rating. P.E. approved, job- specific comparative analysis may be available for these non-rated units. Please contact your Sierra Pacific Windows (“SPW”) Inside Sales group to determine available options for non-rated product. A complete list of rated products is available at WWW.SIERRAPACIFICWINDOWS.COM. If units are being installed in an area requiring specific PG ratings, the unit must be installed in the exact manner tested, as shown in the SPW certified installation details. These details can be found on the Florida Building Code website at www.floridabuilding.org or can be obtained by contacting SPW’s Architectural Services Department at WNASG@spi-ind.com. SPW offers a variety of wood species produced in combinations of solid and veneer-wrapped wood parts that have varying grain patterns. Wood characteristics vary according to the species of the wood. The combination of these items may result in color variations of products with stained or clear finishes. CODES This quote may include an “i89” glazing option. An “i89” glazing option may increase the chance of room side glass condensation in areas where the winter outdoor temperatures are below freezing (32°F/0°C). THERMAL PERFORMANCE PRICING Building codes in many jurisdictions require the addition of limiting devices on any operating unit installed where the finished clear opening of the unit is within 24” of the floor and is more than 72” above the finished grade or other surface below the window. Please check with your local building department to determine if this code is a requirement in your jurisdiction and order products accordingly. Windows denoted with an 'E' on the line item image meet egress based off criteria from the International Residential Code. Each has at least 20" clear opening width, 24" clear opening height and a total clear opening of at least 5.7 square feet. The window sill height and clear opening requirements must be reviewed for code compliance in your local jurisdiction. COLOR VARIATION RATINGS ALUMINUM CLAD UNITS ONLY: **SPW recommends through frame installation for units with factory applied brickmould.** WARRANTY ELEVATION DRAWINGS All pricing is good for 30 days, unless specifically noted to the contrary. The quoted pricing is not final and is subject to revised price book releases and changes until the order has been submitted. Other exceptions may apply. Shop drawing charges are not included, unless specifically noted. SPW assumes no responsibility for errors in take-offs or pricing. 4 Of 3 Page* All drawings are viewed from exterior of window. 1/21/2026CQWPNL QUOTE # 2015646 JASON KELLER / CASH107 / JCAMP QUOTE NAME PROJECT JASON KELLER / CASH107 / JCAMP JOB NAMEPO # CUSTOMER PO # Unless otherwise noted on a line item, the product sold per this Agreement is covered under a SPW limited warranty. Please see your distributor, the SPW Website at WWW.SIERRAPACIFICWINDOWS.COM or our marketing literature for a copy of the applicable limited warranty for specific language, limitations and exclusions. You are expected to provide a copy of the applicable limited warranty to the owner of the real property who benefits from the SPW limited warranty coverage. Products manufactured by others and purchased from SPW will be covered by the product manufacturer’s warranty. SPW provides a Modified Limited Warranty for certain windows and doors, including, but not limited to: 1. Products exceeding their certified test/design size as defined by the Window and Door Manufacturer’s Association (WDMA) Hallmark Program. 2. Products subjected to conditions exceeding their WDMA Hallmark certified design pressure limitations. Products described in Items 1 and 2 are not certified for air infiltration, water penetration, structural loading, forced entry or hardware load testing. These products carry a warranty on the exterior aluminum clad finish and insulated glass only. Customer is advised to carefully review the Limited Warranty for the specific provisions applicable to the products purchased. Due to the design of ADA compliant and low profile sills, products with these sills do not carry a design pressure (DP) rating for air or water infiltration and will not provide the same air or water performance as products with a standard sill height and design configuration. They are, therefore, susceptible to air and water leakage. 1. Sierra Pacific doors with ADA compliant and low profile sills carry a warranty on the metal clad coating and insulated glass only. 2. There are a variety of design options that can be incorporated into your building to help overcome potential air and water leakage inherent to products with low profile sills. These include recessing the doors and/or windows back from the outside plane of the building envelope, using large overhangs, and/or placing awnings above the products. We Appreciate Your Business! WARRANTY MODIFIED LIMITED WARRANTY LOW PROFILE SILLS 4 Of 4 Page* All drawings are viewed from exterior of window. 1/21/2026CQWPNL Vinyl Window Specs

Source: City of Spartanburg website. First collected Oct 17, 2026.