RecordWell Data

Historic Landmarks Commission Meeting Packet (PDF)

City of Suffolk · Suffolk City County · meeting of Aug 13, 2026 · Agenda packets

Open the original document More from City of Suffolk

Text

Extracted automatically from the original. Tables and formatting may not survive; the original document is authoritative.

City of Suffolk HISTORIC LANDMARKS COMMISSION August 13, 2026 THE REGULAR MEETING OF THE HISTORIC LANDMARKS COMMISSION WILL BE HELD AT 9:00 A.M. IN CITY COUNCIL CHAMBERS CITY HALL BUILDING Note: If You Cannot Attend This Meeting, Please Notify the Planning Division by 12:00 Noon, Wednesday, August 12, 2026 (757) 514-4060 PREPARED BY THE CITY OF SUFFOLK DEPARTMENT OF PLANNING & COMMUNITY DEVELOPMENT DIVISION OF PLANNING AGENDA Historic Landmarks Commission Meeting Thursday, August 13, 2026 9:00 a.m. __________________________________________________________ I. Call to Order II. Roll Call III. Approval of the Minutes IV. Cases to be Heard A. Request for Certificate of Appropriateness HLC 2026-00011, submitted by G. Wayne Rhoads on behalf of the City of Suffolk, applicant and property owner, to rehabilitate the façade and storefront openings, and renovate the car parking lot at 157 N. Main Street. The property is further identified as Zoning Map Number 34G18(A)*319, 34G18(5)*11, 34G18(5)*10, 34G18(A)*316, 34G18(5)*11A, 34G18(A)*318*320+, Suffolk Voting Borough, zoned CBD, Central Business District, and HC, Historic Conservation Overlay District B. Request for Certificate of Appropriateness HLC2026 -00012, submitted by G. Wayne Rhoads on behalf of the City of Suffolk, applicant and property owner, to rehabilitate the car parking lot and develop a landscaped pedestrian area at 347 E. Washington Street. The property is further identified as Zoning Map Number 34G25(A)*5, Suffolk Voting Whaleyville, zoned FRRD, Fairgrounds Revitalizations and Redevelopment District, and HC, Historic Conservation Overlay District. V. Staff Reports A. Administrative Approvals B. Property Maintenance Update C. Zoning Update VI. Announcements VII. Adjournment MINUTES HISTORIC LANDMARKS COMMISSION March 12, 2026 9:00 A.M. The regular meeting of the Historic Landmarks Commission was held on Thursday, March 12, 2026, at 9:00 a.m., in the Council Chambers of Suffolk City Hall, 442 W. Washington Street, Suffolk, Virginia, with the following persons present: MEMBERS PRESENT: STAFF: Susan Coley Meg Pittenger, Assistant Director of Planning Keith Emerson Sean Dolan, Assistant City Attorney III Oliver Hobbs Jonathan McBride, Comprehensive Planning Manager Edward King Goncalo Borges, Senior Planner Marsha Reid Darryl King, Housing/Property Maintenance Inspector Brian Shaffer Jennifer Cobb, Assistant Director of CD Vivian Turner Chairman Hobbs called to order the March (2026) meeting of the Historic Landmarks Commission at 9:00 a.m. Meg Pittenger called the roll, and Chairman Hobbs was informed that a quorum was present. APPROVAL OF THE MINUTES: The minutes of the previous meeting were approved as presented. NEW BUSINESS: Request for Certificate of Appropriateness HLC2026-00005, submitted by Chris Shelton of Cure, applicant on behalf of Elliott Apartments LLC, property owner, to install externally lighted marque sign on the front façade at 177 N. Main Street. The property is further identified as Zoning Map Number 34G18(A)*324, Suffolk Voting Borough, zoned CBD, Central Business District Zoning District, and HC, Historic Conservation Overlay District. The first item of business was introduced by Chairman Hobbs followed by a staff report from Jonathan McBride, Comprehensive Planning Manager . Per Mr. McBride, t he subject property is a portion of a contributing structure located at 181 N. Main Street as the primary structure (also known as “Suffolk Towers Apartments, Elliot Hotel, or Elliot Apartments”), and it is within the Original 2 Suffolk District (1987) and the Suffolk Historic Conservation Overlay Zoning District. It is one of the 4 commercial bays in that building. The applicant is proposing to install a black lighted sign bracket to the front entryway façade near the entryway to the bay and suspend a PVC wood appearance marquee sign, 30” long x 18” high, 3.75 sq ft, with engraved black lettering on a white background. Based on the previous historic images from the 1930s and 1950s , this building had awnings and signage. As far as changing the character of the frontage, there will be minimal impact. Based on these findings, staff recommends approval of application, HLC2026-00005. The public hearing was opened, and no one spoke in favor or opposition of the application. The public hearing was closed and after a brief discussion, Commissioner Emerson made a motion to accept staff’s recommendation for approval of application HLC2026-00005. The motion was seconded by Commissioner Turner. The motion passed with a roll call vote of 7 to 0. Request for Certificate of Appropriateness HLC2026 -00006, submitted by Thomas Powell, applicant and property owner, to reopen and restore the original storefront window openings on the front facade, and restore and repaint the existing windows and door at 155 E. Washington Street. The property is further identi fied as Zoning Map Number 34G18(A)*281*B, Suffolk Voting Borough, zoned CBD, Central Business District, and HC, Historic Conservation Overlay District. The second item of business was introduced by Chairman Hobbs followed by a staff report from Goncalo Borges, Senior Planner. Mr. Borges informed the Commission that the applicant is proposing the following actions: 1. To reopen the superior window opening by carefully removing the non-historic materials currently occupying the opening. 2. Installing new windows with clear glazing and dark metal framing designed to match the historic commercial storefront proportions. The window size is 36” in height by 15’ width and will have a window framing 3250 Series 3-1/4” Thermal Fixed, Casement & Projected Windows manufactured by Winco. 3. The superior window will be painted using the color Midnight Hour PPG1038-7 from the HLC’s approved PPG Paints’ Historic Paint Color Collection. 4. Refurbish and paint the existing facade’s lower windows and door, inclusive of frame and trim, by using the same selected color, Midnight Hour PPG1038-7. Based on the HLC guidelines, the proposed work does not negatively impact the integrity of the district. Staff recommends approval of application, HLC2026-00006. 3 The public hearing was opened, and Mr. Thomas Powell, the owner of 155 E. Washington Street, spoke in favor of the application. Per Mr. Powell, the restoration is intended to return the storefront closer to the original 1940s design. Mr. Powell also informed the Commission that the brick was not going to be removed beyond what was necessary and all paint colors were from the city’s approved historic pallet. With no other person speaking in favor or opposition of the application, the public hearing was closed and after a brief discussion, Commissioner Emerson made a motion for approval of application, HLC2026-00006. The motion was seconded by Commissioner King. The motion passed with a roll call vote of 7 to 0. National Registry Nomination of the Ames-Old Farm: Johnathan McBride gave a staff report on the Ames-Old Farm, a 4.7-acre farm located near the city’s northern boundary, which is intersected by the Nansemond River. The property fronts Knotts Creek. To the north and west, the property is contiguous with a 281- acre parcel of undeveloped farmland which is protected under a conservation easement held by the Virginia Outdoors Foundation. The primary resource on the property is a two- and-a-half-story, three -bay frame dwelling originally constructed circa 1820, with a series of historic additions dating from the mid-19th through the mid- 20th century. The property also includes six historic outbuildings that date from the mid-19 th to the early-20th century: a barn, corncrib, garage, schoolhouse, potato cellar and a gas house. Staff recommends support by the Commission o f the Ames-Old farm nomination for recognition on the National Register of Historic Places as an individually contributing propert y. With the recommendation, staff will provide comments to DHR that will include the Commission’s nomination for the National Registry. Commissioner Emerson made a motion for approval and was seconded by Commissioner King. The motion passed with a roll call vote of 7 to 0. By-Laws Change: Jonathan McBride gave a staff report on the new Historic Landmarks Commission By-Laws Change. Mr. McBride informed the Commissioner that over the last few months, staff have been re- evaluating the application process that would potentially help applicants as well as the Commission. Three changes will be going into effect. First, according to the guidelines, the Historic Landmark Commission is required to have a public meeting but not a public hearing. Staff recommends a change to simplify this process to make sure that the process is focused on a public meeting. Public notice will still be provided but it’s not provided as a public hearing; secondly while at the public meeting, the applicant can speak on behalf of their application, but other speakers do not have to be 4 in attendance. The last change involves the timing of public meetings. In the past, if someone is denied by the Commission, it would take almost 60 days for the application to come back before them. A change will simplify this process so that the application can come back before the Commission within 30 days. Commissioner Emerson made a motion for approval of application, HLC2026-00006. The motion was seconded by Commissioner Shaffer . The motion passed with a roll call vote of 7 to 0. STAFF REPORTS: HLC Administrative Approvals: Meg Pittenger Property Maintenance Update: Darryl King • Report included in March Meeting Agenda Packet Zoning Update: Nathan Davidson • Report included in March Meeting Agenda Packet ANNOUNCEMENTS: Ms. Pittenger informed the Commission that we will not have a meeting in April of 2026. There being no further business, the meeting was adjourned. HISTORIC LANDMARKS COMMISSION March 12, 2026 Motion: Approval of HLC2026- 00005 Motion: Approval of HLC2026-00006 Motion: Approval of Ames-Old Farm Motion of Support Motion: Approval of By-Laws COMMISSIONERS ATTENDANCE 1st: Emerson 2nd: Turner 1st: Emerson 2nd: King 1st: Emerson 2nd: King 1st: Emerson 2nd: Shaffer PRESENT ABSENT YES NO YES NO YES NO YES NO Bissell, William N.  Coley, Susan      Emerson, Keith      Hobbs, Oliver, Chairman      King, Edward L.      McCormally, Kristy  Reid, Marsha      Shaffer, Brian      Turner, Vivian      Quorum Present: Yes Vote: 7-0 Motion Approved Vote: 7-0 Motion Approved Vote: 7-0 Motion Approved Vote: 7-0 Motion Approved CITY OF SUFFOLK 442 W. WASHINGTON ST., P.O. BOX 1858, SUFFOLK, VIRGINIA 23439-1858 PHONE: (757) 514-4060 FAX: (757) 514-4099 DEPARTMENT OF PLANNING & COMMUNITY DEVELOPMENT Division of Planning To: Historic Landmarks Commission From: Goncalo Borges, Senior Planner Date: August 13, 2026 Subject: Request for Certificate of Appropriateness HLC202 6-00011, submitted by G. Wayne Rhoads , applicant and agent, on behalf of the City of Suffolk, property owner, to paint the north, south, and west façades, repair the masonry on the east façade, install new storefront openings, metal canopies, brick wall infill, and renovate the parking lot at 157 N. Main Street. The property is further identified as Zoning Map Number 34G18(A)*319, 34G18(5)*11, 34G18(5)*10, 34G18(A)*316, 34G18(5)*11A, 34G18(A)*318*320+, Suffolk Voting Borough, zoned CBD, Central Business District, and HC, Historic Conservation Overlay District. STAFF REPORT Overview and Proposed Actions The subject property is located at 157 N. Main Street. The subject properties are the Virginia Pilot Building, currently occupied by Suffolk’s Economic Development Authority, and an active public parking lot that serves this office building and other adjacent businesses. Per the National Register of Historic Places r ecords (East Washington Street District, 2002 expansion), the sequence of buildings from 151 to 161 North Main Street, of which the Virginia Pilot Building is part, are contributing vernacular commercial buildings, developed between 1935 and 1949. The subject structure is 2 stories tall, with a solid poured concrete foundation, stretcher bond brick structural system, and a flat roof. The building is currently characterized by an eastern façade composed of blonde exposed brick, three doors and eight windows on the street level, and ten windows on the first floor. The building also has painted (white) brick in the southern, western, and northern façades . T he western façade (commonly perceived as the rear of the building) currently includes one storefront, five doors, and three windows on the first floor. The southern façade abuts the adjacent building and has no features other than painted brick. HLC2026-00011 August 13, 2026 Page 2 The applicant is proposing the following actions: • Paint the already painted (white) north, south, and west façades with PPG’s Paint Collection: “New England Regional – Atrium White PPG 1020-1”. • Repair the exposed blonde brick masonry on the east façade (facing North Main Street) with in-kind materials -inclusive of tooth in new brick veneer, repoint brick as required to achieve uniformity, and patch CMU and brick. • Create a new opening and i nstall a new aluminum storefront window on the west façade (facing the parking) matching the already existing door and storefront window, and open a smaller window to its left. • Install 4 metal canopies on the west façade and replace the existing ones. • Brick wall infill to close an unused door in the west façade. • Renovate the parking lot by paving it with heavy-duty asphalt, 6” wide concrete sidewalks, and rearranging the parking spaces to create 48 new parking spaces. • Plant 4 October Glory Maples, 8 Sawtooth Oaks, 16 Dwarf Burford Holly (shrubs), 69 Big Blue Lilly Turf, 3,774 SF of Turf Seed, and 701 SF of Shredded Hardwood Mulch. • Install 4 LSI Lighting “SLM” Series lights and poles in the parking area. • Install 2 “TRP2” Series lights on the southern face (alleyway) of the structure. Case History • In 2002, the subject structure was included in the National Register of Historic Places at the time of the East Washington Street District expansion. • On June 2 nd, 2022, the subject property received a Certificate of Appropriateness (CoA, HLC2022-00017) to install a handicap ramp; this ramp was not proposed to be attached to the structure. Public Notice This request has been duly advertised in accordance with the public notice requirements in Section 15.2-2204 of the Code of Virginia, as amended, and with the applicable provisions of the Unified Development Ordinance. A notice, containing a copy of the staff report, was also provided to the applicant on August 7, 2026. Applicable Regulations A. Unified Development Ordinance (UDO) • Section 31-413(f)(1)D, Issuance of Certificates: The Historic Landmarks Commission shall not issue a Certificate of Appropriateness authorizing issuance of any permit if it finds that the action proposed would adversely affect the primary character of the district or the setting of structures and premises of substantial public interest. • Section 31 -413(g)(2), General Considerations : The compatibility with the design, development standards and criteria as included in the City’s adopted Historic District Design Guidelines. HLC2026-00011 August 13, 2026 Page 3 B. Suffolk Historic District Design Guidelines (8-16-2023 Version) • Chapter 2, Masonry (pages 15 – 18). • Chapter 2, Commercial Storefronts (pages 33 – 39). • Chapter 4, New Construction (pages 70 – 75). • Chapter 5, Site & Setting (pages 77 – 92). C. The Secretary of the Interior’s Standards for Rehabilitation • A property shall be used for its historic purpose or be placed in a new use that requires minimal change to the defining characteristics of the building and its site and environment. • New additions, exterior alterations, or related new construction shall not destroy historic materials that characterize the property. The new work shall be differentiated from the old and shall be compatible with the massing , size, scale, and architectural features to protect the historic integrity of the property and its environment. • Designing new onsite parking, loading docks, or ramps when required by the new use so that they are as unobtrusive as possible and assure the preservation of the historic relationship between the building or buildings and the landscape. • Complying with barrier -free access requirements, in such a manner that character - defining spaces, features, and finishes are preserved. • Not recommended: Removing or radically changing buildings and their features or site features which are important in defining the overall historic character of the property so that, as a result, the character is diminished. • Not recommended: Introducing a new landscape feature, including plant material, that is visually incompatible with the site, or that alters or destroys the historic site patterns or vistas. • Not recommended: Placing parking facilities directly adjacent to historic buildings where automobiles may cause damage to the buildings or to important landscape features. Staff Analysis Upon reviewing the application materials and proposed scope of work, staff finds that the proposed work on the Virginia Pilot Building (157 N. Main Street) as well as the parking lot improvements are in substantial alignment with the UDO, and with the Suffolk Historic District Design Guidelines (8-16-2023 Version). Façade work: The applicant is proposing several actions on the different facades of the subject structure : paint HLC2026-00011 August 13, 2026 Page 4 the already painted ( in white) north, south, and west façades with the pre-approved PPG’s Paint Collection: “New England Regional – Atrium White PPG 1020-1”, repair the exposed blonde brick masonry on the east façade (facing North Main Street) with in -kind materials - inclusive of tooth in new brick veneer, repoint brick as required to achieve uniformity, and patch CMU and brick , create a new opening and install a new aluminum storefront window on the west façade (facing the parking) matching the already existing door and storefront window, open a smaller window to the left of the new opening, install four metal canopies on the west façade and replace the existing ones, and execute a brick wall infill to close an unused door in the west façade. Per Section 31-413(f)(1)D, the proposed façade improvements do not adversely affect the primary character of the district or the setting of structures and premises of substantial public interest. Per Section 31-413(g)(2), all the materials such as brick, mortar, and metal are considered appropriate to this second-generation historic setting. Considering Chapter 2 of the Historic District Design Guidelines, which guides masonry works and commercial façade treatment, the applicant is correctly attempting to preserve the historical material found in the east façade, which is composed of unpainted blonde brick. On this façade, the proposed actions aim to restore the original quality of the façade, without altering the historic character of the structure or adding conflicting elements. The applicant is proposing to use in-kind materials where replacements are needed, and the work in the veneers is appropriate given that it maintains the original historic design. The proposed actions on the east façade, facing North Main Street, accomplish the Historic District Guidelines of preserving and restoring the visibility of historic materials, because the proposed brick matches the historic in color, texture, size, and composition. The north, west, and south facades are currently painted in white, and the west façade presents a second-generation storefront that has been altered during the course of the last century. Since these façades are already painted, the historic guidelines permit that such painted masonry can be repainted. The proposed color is the New England Regional – Atrium White PPG 1020-1, which is a pre -approved color by the Historic Conservation Overlay District/Historic Landmarks Commission. Therefore, staff finds this treatment appropriate and in conformity with the Historic District guidelines and generally with the Secretary of the Interior’s standards for rehabilitation. The applicant is proposing to open a new storefront window just to the left of the existing storefront, as well as opening a small new window to the left of the proposed opening . The applicant is also aiming to infill a door that is located in the northwest corner of the façade and install 4 metal canopies – matching the existing metal canopy. This façade is a second-generation storefront with modern features , which shows evidence of alterations during the last century – initially, the rear of this building does not appear to have been designed to have a storefront, but instead back doors and service doors. The façade currently includes, on the first floor, 5 service doors, a storefront door with windows, and 3 small windows on the second floor. Per Chapter 2’s Commercial Storefronts section (pages 33 – 39), the details of a storefront provide important information about the style and era of the structure. All eras of storefront designs feature large windows for displaying goods, but the materials and details differ over time. The guidelines also emphasize tha t storefronts are often updated to reflect current trends and marketing techniques. Simultaneously, the guidelines recommend that if the existing storefront is modern and requires repairs, the repairs should be accomplished with a matching finish and size. The HLC2026-00011 August 13, 2026 Page 5 current guidelines direct that the historic materials, dimensions, and profile be replicated, as well as suggest that property owners replicate any historic features, details, or ornament, and use clear glass in a storefront. Given the second-generation and already modernized west façade, the proposed actions to include a new display storefront window, opening a smaller window, infill the unused door, and adding 4 metal canopies over the doors by using appropriate materials, designs, and textures that replicate the existing second-generation features, are deemed appropriate by the guidelines. These actions do change the west façade’s appearance, but the proposed additions are executed by using in-kind materials; the design respects the existing second-generation character, and it is also adequate given that the guidelines expect that storefronts are often updated to reflect current trends and marketing techniques. It is staff opinion that the proposed actions , while changing the façade’s design, it does so in a manner that is respectful of the historic materials, context , and character, and it does improve the functionality and aesthetics of this second-generation and modernized façade. Parking lot improvements: The applicant is proposing to redevelop the parking lot behind the Virginia Pilot Building to include 48 spaces to serve this historic building and other surrounding businesses/institutions. This work includes the following actions: Demolishing the existing pavement and sidewalks, repaving the surface with heavy-duty asphalt, creating a total of 48 parking spaces, and installing a 6” wide concrete sidewalk per VDOT standards. These improvements have been designed not to interfere with , obstruct, or be adverse to the adjacent historic Virginia Pilot Building, and to the district in general. Per Section 31-413(f)(1)D, the proposed parking lot improvements do not adversely affect the primary character of the district or the setting of structures and premises of substantial public interest. Per Section 31 -413(g)(2), all the materials such as asphalt and concrete are considered appropriate to this use and setting. These materials are already present in the Historic District, and the proposed features, such as the asphalt parking surface and sidewalk, are compatible with the design, development standards, and criteria as included in the City’s adopted Historic District Design Guidelines. Considering Chapter 4 of the Historic District Design Guidelines, which guides new construction, and the Secretary of the Interior’s Standards for Rehabilitation, the proposed parking lot improvements are designed to maintain the historic character of the subject property by keeping the design and choice of materials simple and without conflicting or risking damaging the Virginia Pilot Building. The proposed features also match with other parking lots developed and maintained by the City of Suffolk within the historic district. In what concerns Chapter 5 (Site & Setting guidelines) and other recommendations by the Secretary of the Interior, the proposed parking lot and its features provide an adequate transition of public and private spaces between the public right of way and the adjacent structure. The installation of sidewalks and two ADA accessible spaces offers accessibility to those using the parking area and the building, and operates as a buffer between the parking area and the building. HLC2026-00011 August 13, 2026 Page 6 These actions are proposed without negatively impacting the historic value of the historic structure and the unified feel in the district. The installation of the proposed parking lot on the western side (typically perceived as the rear) of the Virginia Pilot Building also assures compliance with the Historic District guidelines. Pedestrian and landscaping improvements: The applicant is proposing a series of landscaping improvements that would revitalize the subject property and offer beautification, necessary pervious surface, and shade to the parking area serving the Virginia Pilot Building. Hence, the applicant is proposing to plant 4 October Glory Maples, 8 Sawtooth Oaks, 16 Dwarf Burford Holly (shrubs), 69 Big Blue Lilly Turf, 3,774 SF of Turf Seed, and 701 SF of Shredded Hardwood Mulch. The applicant is also aiming to install 4 LSI Lighting “SLM” Series lights and poles in the parking area, and install 2 “TRP2” Series on the southern façade (alleyway) of the structure to illuminate the parking area and alleyway on the subject property. Per Section 31-413(f)(1)D, the proposed landscaping and lighting improvements do not adversely affect the primary character of the district or the setting of structures and premises of substantial public interest. Per Section 31-413(g)(2), all the materials and features, such as the trees, sod, and lighting poles, are considered appropriate and already present in the historic district. All landscaping and lighting features are compatible with the design, development standards, and criteria as included in the City’s adopted Historic District Design Guidelines. Per Chapters 4 and 5 of the Historic District guidelines, and considering the recommendations by the Secretary of the Interior, the staff finds that the proposed concrete sidewalk with tree wells, the streetlight pole and fixture , and the plantings (sod, shrubs, and trees) are consistent with the Historic District character, thus offering a unified feel to the streetscape . These are compatible with the materials and architecture of the adjacent structures in the vicinity; for reference, the “LSI Lighting “SLM” Series ” streetlight pole and fixture are existing in the current parking lot site . Essentially, the applicant would be replacing these items in kind. The arrangement of the landscaping and lighting features (as well as of the parking lot) is consistent with those on the same street block and accomplishes the goal of retaining the historic character of the streetscape and the rhythm of solids and voids along the street. These improvements have compatible materials, colors, and features with those present in the Historic District, and simultaneously enhance North Saratoga streetscape/parking options and also this parking area that will serve the Downtown with 48 parking spaces . Lastly, the proposed improvements are proposed as unobtrusive to the Virginia Pilot Building and assure the preservation of the historic relationship between this structure, adjacent structures, and the overall landscape. HLC2026-00011 August 13, 2026 Page 7 Recommendation In sum, staff have reviewed the proposed actions with respect to the applicable requirements of the HC Overlay zoning district and determined that the proposed project meets them. It is staff's opinion that improving the subject property by repairing the masonry, painting, and improving the western façade by adding a storefront windows, a small window, and metal canopies, as well as renovating the adjacent parking area is appropriate since it aligns with the standards set by the Historic District Guidelines and by the UDO, as well as follows the recommendations set by the Secretary of the Interior’s Standards for Rehabilitation. Based on the above findings-of-fact and conditions outlined above, staff recommends approval of a Certificate of Appropriateness for the request sought under HLC2026-00011 for the actions described in this staff report. Therefore, staff recommends approval of the following actions as summarized below concerning HLC2026-00011 and as further detailed and specified in the COA application: • Paint the already painted (white) north, south, and west façades with PPG’s Paint Collection: “New England Regional – Atrium White PPG 1020-1”. • Repair the exposed blonde brick masonry on the east façade (facing North Main Street) with in-kind materials -inclusive of tooth in new brick veneer, repoint brick as required to achieve uniformity, and patch CMU and brick. • Create a new opening and i nstall a new aluminum storefront window on the west façade (facing the parking) matching the already existing door and storefront window, and open a smaller window to its left. • Install 4 metal canopies on the west façade and replace the existing ones. • Brick wall infill to close an unused door in the west façade. • Renovate the parking lot by paving it with heavy-duty asphalt, 6” wide concrete sidewalks, and rearranging the parking spaces to create 48 new parking spaces. • Plant 4 October Glory Maples, 8 Sawtooth Oaks, 16 Dwarf Burford Holly (shrubs), 69 Big Blue Lilly Turf, 3,774 SF of Turf Seed, and 701 SF of Shredded Hardwood Mulch. • Install 4 LSI Lighting “SLM” Series lights and poles in the parking area. • Install 2 “TRP2” Series lights on the southern face (alleyway) of the structure. Attachments • Site Maps • Narrative • Site Photography • Virginia Pilot Building - Proposed Work Elevations • Site Plans – Proposed Conditions, Landscaping, Photometric Sources: Esri, TomTom, Garmin, FAO, NOAA, USGS, © OpenStreetMap contributors, and the GIS User Community 01 . 534 . 560.75 Miles ^_ Author: KOSSAI Date: 07-06-2026 ± GENERAL LOCATION MAP HLC2026-00011 Subject Property VILLAGE TRADITIONAL NEIGHBORHOOD SUBURBAN NEIGHBORHOOD RIGHT OF WAY RURAL NEIGHBORHOOD RURAL CONSERVATION RURAL AGRICULTURE PARKS AND OPEN SPACE OFFICE/INSTITUTIONAL MIXED USE CORE MULTIFAMILY NEIGHBORHOOD Employment Center COMMERCIAL CORRIDOR Central Growth Area ^_ SUBJECT PROPERTY MARKET ST W WASHINGTON ST EWASHING TON ST CAROLINA RDCAROLINA R D BANK ST PINE ST S SARATOGA ST CLAY ST N SARATOGA ST N MAIN ST N SARATOGA ST 34G18(A)*319 350401000 34G18(A)*318*320+ 352025000 34G18(A)*316 353327000 34G18(5)*10 353328000 34G18(5)*11 353329000 34G18(5)*11A 353747600 RU CBD RM B-1 0 100 200 300 40050 Feet Subject Property Image: Suffolk Pictometry 2024 Author: KOSSAI Date: 07-06-2026 ± ZONING / LAND USE MAP HLC2026-00011 MARKET ST N MAIN ST N SARATOGA ST 34G18(A)*319350401000 34G1 8(A )*3 18*320+ 352 025000 34G18(A)*316353327000 34G18(5)*10 353328000 34G18(5)*11 353329000 34G18(5)*11A 353747600 0 40 80 120 16020 Feet EXHIBIT B Subject Property Author: KOSSAI Date: 07-06-2026 ± PROPERTY MAP HLC2026-00011 N MAIN ST MARKET ST ECONS TANCE RD W W ASHINGTON ST CEDAR ST E WASHINGTON ST YORK ST WELLONS ST CAROLINA RD FAYETTE ST N SARATOGA ST FAYETTEST PITCHKETTLE RD SMITH ST MARYLAND AVE PITCHKETTLEVILLAGE ST JACKSON ST KATHERINE ST CULLODEN ST S SARATOGA ST WHITE MARSH RD JOHNSON AVE W CONSTANCE RD BANK ST CAROLINA RD ELEY CT FACTORY ST BUTE ST W FINNEY AVE RIVER POINT DR LINDEN AVE MOUNT HOREB ST NEWPORT ST FREENEY AVE MORGAN ST MILITARY RD HENLEYPL BANK ST EXT AZALEA CT GARFIELD AVE JOHNSON AVE MULBERRY ST WEST ERN AVE NANSEMOND AVE CHURCH ST HALL AVE HILL ST CEDAR ST SPUR BEECH ST CAMP AVE YORK CT DAYST TYNES ST OAK ST E PINNER ST CHERRY ST BROOK AVE PINE ST SPRING ST OAKLAND ST RIVER POINT DR MA DISONAVE POPLAR AVE FOREST HILL CRES N BROAD ST S DIVISION ST MOUNT SINAI ST NANSEMOND AVE TRADD ST DUMVILLE LN ORCHARD AVE GRAYSON CT CENTRAL AVE RIVERVIEW CT BOAT ST CAUSEY AVE KENNEDYCT CLARYS DR BETHLEHEM ST JOHNSONAVE MASON AVE HIGHLAND AVE OAKDALE TER PARKWAY ABRAHAM ST NORTH ST WILSON ST RENOST S BROAD ST MAHAN ST VIRGINIA AVE VIRGINIA AVE S MAIN ST POLKST RICHARDSON ST ASHLEY AVE LINDEN AVE KNIGHTST CANNON ST PITCHKETTLE RD RAILROAD AVE DUKE ST TERRACE CT PINNER ST HOLLADAY ST W RIVERVIEW DR COLLEGE CT SECOND AVE GRANBY ST SUNSETAVE COLLIEAVE FIRST AVE GRACE ST THIRD AVE WALNUT ST SECOND AVE MAPLE ST MULBERRY ST CAUSEY AVE PENDER ST GLOUCE ST ER ST N DIVISION ST RIDLE YST LINCOLN AVE BOSLEY AVE LEXI NGTON AVE FORT ST VAN BUREN AVE JEFFERSON ST ADAMS STLAKES IDE ST EUGENIA ST KINGSBORO ST ALLEN ST GITTINGS ST ELIZABETH ST PARK RD JOHNSON LN DOGWOOD LN FINNEY AVE BATTERY AVEBROOK AVE FREEMASON ST HOWAR D PL CAROLINA AVE NEVADA ST LEE ST N & W AVE COUNTY ST WILLOWST S BROAD ST SPRUCE ST SAINT JAMES AVE PEARL ST COMMERCE ST SOUTH ST N LLOYD ST JONES ST DUMVILLE AVE CHARLES ST LINDEN AVE LINDEN AVE BREWER AVE FOREST ST W FINNEYAVE WARWIC K ST N CAPITAL ST SAINT JAMES AVE FRANKLIN ST CHESTNUT ST PINE ST ROANOKE ST COMMERCE ST FOURTH ST CLAY ST HENRY ST RAILROAD AVE LIBERTY ST N DIVISION ST BUTLER AVE N SARATOGA ST DARDEN AVE N LLOYD ST JEFFERSON ST ERIVERVIEW DR HALIFAX ST LOCUST ST SHIPWRIGHT LN PRENTIS ST E RIVERVIEW DR FAIRGROUNDS LN E CONSTANCE RD ECONST AN CE RD MOORE AVE NANSEMOND RIVERLAKE MEADE Disclaimer: THE CITY OF SUFFOLK MAKES NO WARRANTY, REPRESENTATION, OR GUARANTEE OF ANY KIND REGARDING EITHER ANY MAPS OR OTHER INFORMATION PROVIDED HEREIN OR THE SOURCES OF SUCH MAPS OR OTHER INFORMATION. THE CITY OF SUFFOLK SPECIFICALLY DISCLAIMS ALL REPRESENTATIONS OR WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILIY AND FITNESS FOR A PARTICULAR PURPOSE. The City of Suffolk assumes no liability for any errors, omissions, or inaccuracies in the information provided regardless of the cause of such or for any decision made , action taken, or action not taken by the user in reliance upon any maps or information provided herein. Parcel and Zoning information has been developed to provide a graphic representation of the Real Estate Property Tax Maps. The boundaries of any parcel may have been adjusted to provide a more visually pleasing presentation. User should refer to the instrument of transfer (deed or plat) for legal boundary location and perimeter or area measurements. Amended 8/16/2011 by Ordinance No. 11-O-073 0 0.1 0.2 0.3 0.40.05 Miles SCALE: 1:10,000 Legend BUILDING FOOTPRINTS SUFFOLK HISTORIC CONSERVATION OVERLAY NATIONAL REGISTER OF HISTORIC DISTRICTS ORIGINAL SUFFOLK DISTRICT (1987) NORTH MAIN STREET DISTRICT EXTENSION (1998) EAST WASHINGTON STREET DISTRICT (2002) WEST END DISTRICT (2004) WEST END DISTRICT EXPANSION (2004) SUFFOLK DISTRICT EXPANSION (2004) CEDAR HILL DISTRICT (2006) ^_ Author: KOSSAI Date: 07-06-2026 µ Suffolk Historic Conservation Overlay District & National Register GENERAL LOCATION MAP HLC2026-00011 Subject Property GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION EXTERIOR PAINTING 099113 - 1 SECTION 099113 - EXTERIOR PAINTING 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section includes surface preparation and the application of paint systems on exterior substrates. A. Clay Masonry (Brick Veneer) B. Concrete masonry units (CMUs). C. Steel and iron. D. Galvanized metal. B. Section includes surface preparation, painting, and finishing of exposed exterior items and surfaces. A. Surface preparation, priming, and finish coats specified in this section are in addition to shop priming and surface treatment specified under other sections. C. Paint all exposed surfaces whether or not colors are designated in "schedules," except where a surface or material is specifically indicated not to be painted or is to remain natural. Where an item or surface is not specifically mentioned, paint the same as similar adjacent materials or surfaces. If color or finish is not designated, the Architect/Engineer will select from standard colors or finishes available. D. Painting is not required on prefinished items unless otherwise noted, finished metal surfaces, concealed surfaces, operating parts, and Do Not Paint Labels. A. Labels: Do not paint over Underwriter's Laboratories, Factory Mutual or other code-required labels or equipment name, identification, performance rating, or nomenclature plates. E. Related Requirements: A. Section 081113 “Hollow Metal Doors and Frames”. B. Section 099123 “Interior Painting”. 1.3 DEFINITIONS A. MPI Gloss Level 1: Not more than five units at 60 degrees and 10 units at 85 degrees, according to ASTM D 523. GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION EXTERIOR PAINTING 099113 - 2 B. MPI Gloss Level 3: 10 to 25 units at 60 degrees and 10 to 35 units at 85 degrees, according to ASTM D 523. C. MPI Gloss Level 4: 20 to 35 units at 60 degrees and not less than 35 units at 85 degrees, according to ASTM D 523. D. MPI Gloss Level 5: 35 to 70 units at 60 degrees, according to ASTM D 523. E. MPI Gloss Level 6: 70 to 85 units at 60 degrees, according to ASTM D 523. F. MPI Gloss Level 7: More than 85 units at 60 degrees, according to ASTM D 523. 1.4 ACTION SUBMITTALS A. Product Data: For each type of product. Include preparation requirements and application instructions. A. Include printout of current "MPI Approved Products List" for each product category specified, with the proposed product highlighted. B. Indicate VOC content. B. Samples for Initial Selection: For each type of topcoat product. C. Samples for Verification: For each type of paint system and each color and gloss of topcoat. D. Samples for verification purposes: Provide samples of each color and material to be applied, with texture to simulate actual conditions, on representative samples of the actual substrate. Define each separate coat, including block fillers and primers. Use representative colors when preparing samples for review. Resubmit until required sheen, color, and textures are achieved. A. Provide a list of material and application for each coat of each sample. Label each sample as to location and application. B. Submit samples on the following substrates for the Architect's review of color and texture only: a. Concrete Masonry: Provide three (3) 4- by-8-inch samples of masonry for each finish and color. b. Ferrous or Galvanized Metal: Provide three 4-inch-square samples of flat metal and two 8-inch-long samples of solid metal for each color and finish. c. The Contractor shall prepare samples at the job as required until colors and textures are satisfactory. Samples of water base acrylic-epoxy shall be made on 2 feet 0 inches x 4 feet 0 inches x 1/4 plywood panels. Submit four samples. Provide a listing of the material and application for each coat of each finish sample. E. Product List: Cross-reference to paint system and locations of application areas. Use same designations indicated on Drawings and in schedules. Include color designations. GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION EXTERIOR PAINTING 099113 - 3 1.5 MAINTENANCE MATERIAL SUBMITTALS A. Furnish extra materials, from the same product run, that match products installed and that are packaged with protective covering for storage and identified with labels describing contents. A. Paint: Provide 5 gal. of each material and color applied. 1.6 QUALITY ASSURANCE A. MPI Standards: A. Products: Complying with MPI standards indicated and listed in “MPI Approved Products List.” a. Preparation and Workmanship: Comply with requirements in “MPI Architectural Painting Specification Manual” for products and paint systems indicated. B. Single-Source Responsibility: Provide primers and undercoat paint produced by the same manufacturer as the finish coats. C. Coordination of Work: Review other sections in which primers are provided to ensure compatibility of the total systems for various substrates. On request, furnish information on characteristics of finish materials to ensure use of compatible primers. A. Prior to submittals, notify the Architect of any problems anticipated using the materials specified. D. Field Samples: On wall surfaces and other exterior and interior components, duplicate finishes of prepared samples. Provide full- coat finish samples on at least 100 sq. ft. of surface until required sheen, color and texture are obtained; simulate finished lighting conditions for review of in-place work. A. Final acceptance of colors will be from job-applied samples. B. Where colors selected are of a dark or vibrant color not capable of being mixed with a particular manufacturer's paint type equal to paint type specified, provide an equal or better paint type that can provide such color upon approval of the Architect. 1.7 DELIVERY, STORAGE, AND HANDLING A. Deliver materials to the job site in the manufacturer's original, unopened packages and containers bearing manufacturer's name and label and the following information: A. Product name or title of material. B. Product description (generic classification or binder type). C. Federal Specification number, if applicable. D. Manufacturer's stock number and date of manufacture. E. Contents by volume, for pigment and vehicle constituents. F. Thinning instructions. GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION EXTERIOR PAINTING 099113 - 4 G. Application instructions. H. Color name and number. B. Store materials not in use in tightly covered containers in a well-ventilated area at a minimum ambient temperature of 45 deg F. Maintain containers used in storage in a clean condition, free of foreign materials and residue. A. Protect from freezing. Keep storage area neat and orderly. Remove oily rags and waste daily. Take necessary measures to ensure that workers and work areas are protected from fire and health hazards resulting from handling, mixing, and application. 1.8 FIELD CONDITIONS A. Apply solvent-thinned paints only when the temperature of surfaces to be painted and surrounding air temperatures are between 45 deg F and 95 deg F. B. Do not apply paint in snow, rain, fog, or mist, when the relative humidity exceeds 85 percent, at temperatures less than 5 deg F above the dew point, or to damp or wet surfaces. A. Painting may continue during inclement weather if surfaces and areas to be painted are enclosed and heated within temperature limits specified by the manufacturer during application and drying periods. B. Do not apply paint until debris has been removed and spaces have been vacuumed to remove all dust and dirt. PART 2 - PRODUCTS 2.1 MANUFACTURERS A. Manufacturers: Subject to compliance with requirements, provide products by one of the following: A. Benjamin Moore & Co. B. Duron, Inc. C. Glidden Professional. D. PPG Architectural Finishes, Inc. E. Pratt & Lambert. F. Sherwin-Williams Company (The). B. Products: Subject to compliance with requirements, available products that may be incorporated into the Work include, but are not limited to products listed in the Exterior Painting Schedule for the paint category indicated. GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION EXTERIOR PAINTING 099113 - 5 2.2 PAINT, GENERAL A. MPI Standards: Products shall comply with MPI standards indicated and shall be listed in its "MPI Approved Products Lists." B. Material Compatibility: A. Materials for use within each paint system shall be compatible with one another and substrates indicated, under conditions of service and application as demonstrated by manufacturer, based on testing and field experience. B. For each coat in a paint system, products shall be recommended in writing by topcoat manufacturers for use in paint system and on substrate indicated. C. VOC Content: For field applications, paints and coatings shall comply with VOC content limits of authorities having jurisdiction and the following VOC content limits: A. Flat Paints and Coatings: 50 g/L. B. Nonflat Paints and Coatings: 50 g/L. C. Dry-Fog Coatings: 150 g/L. D. Primers, Sealers, and Undercoaters: 100 g/L. E. Rust-Preventive Coatings: 100 g/L. F. Zinc-Rich Industrial Maintenance Primers: 100 g/L. G. Pretreatment Wash Primers: 420 g/L. H. Shellacs, Clear: 730 g/L. I. Shellacs, Pigmented: 550 g/L. J. Light Industrial Coatings: 400g/L. D. Colors: Match Architect's samples. 2.3 SOURCE QUALITY CONTROL A. Testing of Paint Materials: Owner reserves the right to invoke the following procedure: A. Owner will engage the services of a qualified testing agency to sample paint materials. Contractor will be notified in advance and may be present when samples are taken. If paint materials have already been delivered to Project site, samples may be taken at Project site. Samples will be identified, sealed, and certified by testing agency. B. Testing agency will perform tests for compliance with product requirements. C. Owner may direct Contractor to stop applying paints if test results show materials being used do not comply with product requirements. Contractor shall remove noncomplying paint materials from Project site, pay for testing, and repaint surfaces painted with rejected materials. Contractor will be required to remove rejected materials from previously painted surfaces if, on repainting with complying materials, the two paints are incompatible. GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION EXTERIOR PAINTING 099113 - 6 PART 3 - EXECUTION 3.1 EXAMINATION A. Examine substrates and conditions, with Applicator present, for compliance with requirements for maximum moisture content and other conditions affecting performance of the Work. B. Examine substrates and conditions under which painting will be performed for compliance with requirements for application of paint. Do not begin paint application until unsatisfactory conditions have been corrected. A. Starting of painting work will be construed as Applicator's acceptance of surfaces and conditions within any particular area and that the room has been completely vacuumed and all airborne dust will not affect painting procedures or paint finish. If airborne dust can migrate from other areas, Contractor shall provide dust partitions or doors to prohibit migration. B. Applicator must examine areas and conditions under which painting work is to be applied and notify Contractor in writing of conditions detrimental to proper and timely completion of work. Do not proceed with work until unsatisfactory conditions have been corrected in a manner acceptable to Applicator. Beginning coating application constitutes Contractor’s acceptance of substrates and conditions. C. Do not paint over dirt, rust, scale, grease, moisture, scuffed surfaces, or conditions otherwise detrimental to formation of a durable paint film. D. Maximum Moisture Content of Substrates: When measured with an electronic moisture meter as follows: A. Masonry (Clay and CMUs): 12 percent. E. Verify suitability of substrates, including surface conditions and compatibility, with existing finishes and primers. F. Proceed with coating application only after unsatisfactory conditions have been corrected. A. Application of coating indicates acceptance of surfaces and conditions. 3.2 PREPARATION A. General Procedures: Remove hardware and hardware accessories, plates, machined surfaces, lighting fixtures, and similar items in place that are not to be painted, or provide surface-applied protection prior to surface preparation and painting. Do not paint over labels of independent testing agencies or equipment name, identification, performance rating, or nomenclature plates. Remove these items if necessary for complete painting of the items and adjacent surfaces. Following completion of painting operations in each space or area, have items reinstalled by workers skilled in the trades involved. GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION EXTERIOR PAINTING 099113 - 7 A. Clean surfaces before applying paint or surface treatments. Remove oil and grease prior to cleaning. Schedule cleaning and painting so that dust and other contaminants from the cleaning process will not fall on wet, newly painted surfaces. B. Surface Preparation: Clean and prepare surfaces to be painted in accordance with the manufacturer's instructions for each particular substrate condition and as specified. A. Provide barrier coats over incompatible primers or remove and reprime. Notify Architect/Engineer in writing of problems anticipated with using the specified finish-coat material with substrates primed by others. B. Cementitious Materials: Prepare concrete, concrete masonry block and cement plaster surfaces to be painted. Remove efflorescence, chalk, dust, dirt, grease, oils, and release agents. Roughen as required to remove glaze. If hardeners or sealers have been used to improve curing, use mechanical methods of surface preparation. a. Use abrasive blast-cleaning methods if recommended by the paint manufacturer. b. Determine alkalinity and moisture content of surfaces by performing appropriate tests. If surfaces are sufficiently alkaline to cause blistering and burning of finish paint, correct this condition before application. Do not paint surfaces where moisture content exceeds that permitted in manufacturer's printed directions. c. Clean concrete floors to be painted with a 5 percent solution of muriatic acid or other etching cleaner. Flush the floor with clean water to remove acid, neutralize with ammonia, and rinse; allow to dry and vacuum before painting. C. Ferrous Metals: Clean nongalvanized ferrous-metal surfaces that have not been shop coated; remove oil, grease, dirt, loose mill scale, and other foreign substances. Use solvent or mechanical cleaning methods that comply with recommendations of the Steel Structures Painting Council. a. Touch up bare areas and shop-applied prime coats that have been damaged. Wire-brush, clean with solvents recommended by the paint manufacturer, and touch up with the same primer as the shop coat. D. Galvanized Surfaces: Clean galvanized surfaces with non-petroleum-based solvents so that the surface is free of oil and surface contaminants. Remove pretreatment from galvanized sheet metal fabricated from coil stock by mechanical methods. C. Materials Preparation: Carefully mix and prepare paint materials in accordance with manufacturer's directions. A. Maintain containers used in mixing and application of paint in a clean condition, free of foreign materials and residue. B. Stir material before application to produce a mixture of uniform density; stir as required during application. Do not stir surface film into material. Remove films and, if necessary, strain material before using. GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION EXTERIOR PAINTING 099113 - 8 3.3 APPLICATION A. Apply paints according to manufacturer's written instructions and recommendations in "MPI Architectural Painting Specification Manual." A. Use applicators and techniques suited for paint and substrate indicated. B. Paint surfaces behind movable items same as similar exposed surfaces. Before final installation, paint surfaces behind permanently fixed items with prime coat only. C. Paint both sides and edges of exterior doors and entire exposed surface of exterior door frames. D. Do not paint over labels of independent testing agencies or equipment name, identification, performance rating, or nomenclature plates. E. Primers specified in painting schedules may be omitted on items that are factory primed or factory finished if acceptable to topcoat manufacturers. B. Apply paint in accordance with manufacturer's directions. Unless otherwise indicated, paint applications shall be by brush or roller. Walls may be spray applied with backrolling. Exposed steel joists, hollow metal frames, and hollow metal doors shall be sprayed on with the final coat brush or roller applied. Exposed metal decks and roll up doors will be allowed to have all coats spray applied. C. Do not paint over dirt, rust, scale, grease, moisture, scuffed surfaces, or conditions detrimental to formation of a durable paint film. A. Paint colors, surface treatments, and finishes are indicated in the Color Schedule. Colors not indicated shall be as selected by the Architect/Engineer. First coat of finish coatings shall have slight tint variation from final coat to distinguish coat applications. Contractor shall not provide second coat in any space until Owner is notified that first coat is complete. Contractor shall maintain color coded chart/drawing in trailers of rooms and coat status. Failure to notify Owner will be cause for additional coat of paint to be applied. B. Provide finish coats that are compatible with primers used. C. The number of coats and film thickness required is the same regardless of the application method. Do not apply succeeding coats until the previous coat has cured as recommended by the manufacturer. Sand between applications where sanding is required to produce an even smooth surface in accordance with the manufacturer's directions. D. Apply additional coats when undercoats, stains, or other conditions show through final coat of paint until paint film is of uniform finish, color, and appearance. Give special attention to ensure that surfaces, including edges, corners, crevices, welds, and exposed fasteners, receive a dry film thickness equivalent to that of flat surfaces. E. The term "exposed surfaces" includes areas visible when permanent or built-in fixtures, convector covers, covers for finned tube radiation, grilles, and similar components are in place. Extend coatings in these areas as required to maintain the system integrity and provide desired protection. F. Paint surfaces behind movable equipment and furniture same as similar exposed surfaces. Paint surfaces behind permanently fixed equipment or furniture with prime coat only before final installation of equipment. G. Paint interior surfaces of ducts, where visible through registers or grilles, with a flat, nonspecular black paint, specifically formulated for the application and complying with requirements of ASHRAE 90.1 for ductwork interior coatings. GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION EXTERIOR PAINTING 099113 - 9 H. Paint back sides of access panels and removable or hinged covers to match exposed surfaces. I. Follow manufacturer's recommendations and instructions carefully regarding special coating product on concrete columns so as to provide the best quality work. D. Scheduling Painting: Apply first coat to surfaces that have been cleaned, pretreated, or otherwise prepared for painting as soon as practicable after preparation and before subsequent surface deterioration. A. Allow sufficient time between successive coats to permit proper drying. Do not recoat until paint has dried to where it feels firm, and does not deform or feel sticky under moderate thumb pressure and where application of another coat of paint does not cause lifting or loss of adhesion of the undercoat. Do not recoat sooner than recommended by paint manufacturer. E. Minimum Coating Thickness: Apply materials at not less than the manufacturer's recommended spreading rate. Provide a total dry film thickness of the entire system as recommended by the manufacturer. F. Mechanical and Electrical Work: Painting mechanical and electrical work is limited to items exposed in mechanical equipment rooms and in occupied spaces. G. Mechanical items to be painted include but are not limited to: A. N/A H. Electrical items to be painted include but are not limited to: A. Conduit and fittings. I. Block Fillers: Apply block fillers to concrete masonry block at a rate to ensure complete coverage with pores filled. J. Prime Coats: Before application of finish coats, apply a prime coat of material as recommended by the manufacturer to material that is required to be painted or finished and has not been prime coated by others. Recoat primed and sealed surfaces where evidence of suction spots or unsealed areas in first coat appears, to assure a finish coat with no burn through or other defects due to insufficient sealing. Factory primed materials shall not constitute the prime coat specified within this specification section. K. Pigmented (Opaque) Finishes: Completely cover to provide an opaque, smooth surface of uniform finish, color, appearance, and coverage. Cloudiness, spotting, holidays, laps, brush marks, runs, sags, ropiness, or other surface imperfections will not be acceptable. L. Transparent (Clear) Finishes: Use multiple coats to produce a glass-smooth surface film of even luster. Provide a finish free of laps, cloudiness, color irregularity, runs, brush marks, orange peel, nail holes, or other surface imperfections. A. Provide satin finish for final coats. GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION EXTERIOR PAINTING 099113 - 10 M. Completed Work: Match approved samples for color, texture, and coverage. Remove, refinish, or repaint work not in compliance with specified requirements. 3.4 FIELD QUALITY CONTROL A. Dry Film Thickness Testing: Owner may engage the services of a qualified testing and inspecting agency to inspect and test paint for dry film thickness. A. Contractor shall touch up and restore painted surfaces damaged by testing. B. If test results show that dry film thickness of applied paint does not comply with paint manufacturer's written recommendations, Contractor shall pay for testing and apply additional coats as needed to provide dry film thickness that complies with paint manufacturer's written recommendations. B. The Owner reserves the right to invoke the following test procedure at any time and as often as the Owner deems necessary during the period when paint is being applied: A. The Owner will engage the services of an independent testing laboratory to sample the paint material being used. Samples of material delivered to the project will be taken, identified, sealed, and certified in the presence of the Contractor. B. The testing laboratory will perform appropriate tests for the following characteristics as required by the Owner: a. Quantitative materials analysis. b. Abrasion resistance. c. Apparent reflectivity. d. Flexibility. e. Washability. f. Absorption. g. Accelerated weathering. h. Dry opacity. i. Accelerated yellowness. j. Recoating. k. Skinning. l. Color retention. m. Alkali and mildew resistance. C. If test results show material being used does not comply with specified requirements and by specified manufacturer's requirements, the Contractor shall be directed to stop painting, remove noncomplying paint, pay for testing, repaint surfaces coated with rejected paint, and remove rejected paint from previously painted surfaces if, upon repainting with specified paint, the two coatings are noncompatible. All corrective work will be at the Contractor's expense. 3.5 CLEANING AND PROTECTION A. At end of each workday, remove rubbish, empty cans, rags, and other discarded materials from Project site. GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION EXTERIOR PAINTING 099113 - 11 B. After completing paint application, clean spattered surfaces. Remove spattered paints by washing, scraping, or other methods. Do not scratch or damage adjacent finished surfaces. C. Protect work of other trades against damage from paint application. Correct damage to work of other trades by cleaning, repairing, replacing, and refinishing, as approved by Architect, and leave in an undamaged condition. D. At completion of construction activities of other trades, touch up and restore damaged or defaced painted surfaces. 3.6 EXTERIOR PAINTING SCHEDULE A. Clay Masonry Substrates: A. High Performance Architectural Latex System: a. Prime Coat: Alkali-resistant, water-based primer. MPI #17 b. Intermediate Coat: Matching topcoat. c. Topcoat: Exterior, high performance architectural latex, low sheen. (MPI Gloss Level 3-4), MPI #15. B. CMU Substrates: A. Latex System MPI EXT 4.2A: a. Prime Coat: Block filler, latex, interior/exterior, MPI #4. b. Intermediate Coat: Latex, exterior, matching topcoat. c. Topcoat: Latex, exterior, low sheen (MPI Gloss Level 3-4), MPI #15. C. Steel and Iron Substrates: A. Water-Based Light Industrial Coating System MPI EXT 5.1C: a. Prime Coat: Primer, zinc rich, inorganic, MPI #19. b. Intermediate Coat: Light industrial coating, exterior, water based, matching topcoat. B. Water-Based Light Industrial Coating over Epoxy System MPI EXT 5.1R: a. Prime Coat: Primer, epoxy, anti-corrosive MPI #101. b. Intermediate Coat: Epoxy, high build, low gloss MPI #108. c. Topcoat: Light industrial coating, exterior, water based, semi-gloss (MPI Gloss Level 5), MPI #163. C. Aluminum Paint System MPI EXT 5.1K: a. Prime Coat: Primer, alkyd, anti-corrosive, for metal, MPI #79. b. Intermediate Coat: Aluminum paint, matching topcoat. D. Galvanized-Metal Substrates: GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION EXTERIOR PAINTING 099113 - 12 A. Light Industrial Coating System: a. Prime Coat: Tnemec Series 66 Hi-build Epoxoline applied at a dry film thickness of not less than 0.5 mils. b. Intermediate Coat: Light industrial coating, matching topcoat. c. Topcoat: Tnemec Series 73 applied at a dry film thickness of not less than 5.0 mils. 1END OF SECTION 099113 GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS 084113 - 1 084113 - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section Includes: 1. Storefront framing for punched openings. B. Related Sections: 1. Division 7 Section “Joint Sealants” for installation of joint sealants installed with aluminum-framed systems and for sealants to the extent not specified in this Section. 2. Division 8 Section “Door Hardware” for hardware to the extent not specified in this Section. 3. Division 8 Section “Glazing” for glazing requirements to the extent not specified in this Section 1.3 ACTION SUBMITTALS A. Product Data: For each type of product. 1. Include construction details, material descriptions, dimensions of individual components and profiles, and finishes. B. Shop Drawings: For aluminum-framed storefronts at punched openings. Include plans, elevations, sections, full-size details, and attachments to other work. 1. Include details of provisions for assembly expansion and contraction and for draining moisture occurring within the assembly to the exterior. 2. Include full-size isometric details of each vertical-to-horizontal intersection of aluminum- framed entrances and storefronts, showing the following: a. Joinery, including concealed welds. b. Anchorage. c. Expansion provisions. d. Glazing. e. Flashing and drainage. f. Conduit configuration coordination with electronic hardware. GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS 084113 - 2 3. Show connection to and continuity with adjacent thermal, weather, air, and vapor barriers. C. Samples for Initial Selection: For units with factory-applied color finishes. D. Samples for Verification: For each type of exposed finish required, in manufacturer's standard sizes. 1 . 4 F a b r i c a t i o n S a m p l e : N/A.INFORMATIONAL SUBMITTALS A. Qualification Data: For Installer. B. Energy Performance Certificates: For aluminum-framed storefronts at punched openings, accessories, and components, from manufacturer. 1. Basis for Certification: NFRC-certified energy performance values for each aluminum- framed storefront. C. Product Test Reports: For aluminum-framed storefronts, for tests performed by manufacturer and witnessed by a qualified testing agency. D. Quality-Control Program: Developed specifically for Project, including fabrication and installation, according to recommendations in ASTM C 1401. Include periodic quality-control reports. E. Source quality-control reports. F. Welding certificates. G. Product Test Reports: Based on evaluation of comprehensive tests performed by a qualified testing agency, for aluminum-framed systems, indicating compliance with performance requirements. H. Field quality-control reports. I. Sample Warranties: For special warranties. 1.5 CLOSEOUT SUBMITTALS A. Maintenance Data: For aluminum-framed storefronts to include in maintenance manuals. B. Maintenance Data for Structural Sealant: For structural-sealant-glazed storefront to include in maintenance manuals. Include ASTM C 1401 recommendations for post-installation-phase quality-control program. GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS 084113 - 3 1.6 QUALITY ASSURANCE A. Installer Qualifications: An entity that employs installers and supervisors who are trained and approved by manufacturer. B. Testing Agency Qualifications: Qualified according to ASTM E 699 for testing indicated and accredited by IAS or ILAC Mutual Recognition Arrangement as complying with ISO/IEC 17025. C. Product Options: Information on Drawings and in Specifications establishes requirements for aesthetic effects and performance characteristics of assemblies. Aesthetic effects are indicated by dimensions, arrangements, alignment, and profiles of components and assemblies as they relate to sightlines, to one another, and to adjoining construction. 1. Do not change intended aesthetic effects, as judged solely by Architect, except with Architect's approval. If changes are proposed, submit comprehensive explanatory data to Architect for review. D. Structural-Sealant Glazing: Comply with ASTM C 1401 for design and installation of storefront systems. E. Source Limitations for Aluminum-Framed Systems: Obtain from single source from single manufacturer. F. Welding Qualifications: Qualify procedures and personnel according to AWS D1.2, "Structural Welding Code - Aluminum." 1.7 FIELD CONDITIONS A. Field Measurements: Verify actual locations of structural supports for aluminum-framed systems by field measurements before fabrication and indicate measurements on Shop Drawings. 1. Established Dimensions: Where field measurements cannot be made without delaying the Work, establish dimensions and proceed with fabricating aluminum-framed systems without field measurements. Coordinate construction to ensure that actual dimensions correspond to established dimensions. 2. The Contractor to coordinate wiring for Keyless Entry System hardware occurring within the aluminum storefront system with the Section 087100 “Door Hardware.” 1.8 WARRANTY A. Special Warranty: Manufacturer agrees to repair or replace components of aluminum-framed storefronts that do not comply with requirements or that fail in materials or workmanship within specified warranty period. 1. Failures include, but are not limited to, the following: GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS 084113 - 4 a. Structural failures including, but not limited to, excessive deflection. b. Noise or vibration created by wind and thermal and structural movements. c. Deterioration of metals, metal finishes, and other materials beyond normal weathering. d. Water penetration through fixed glazing and framing areas. e. Failure of operating components. f. Adhesive or cohesive sealant features. 2. Warranty Period: 10 years from date of Substantial Completion. B. Special Finish Warranty: Standard form in which manufacturer agrees to repair finishes or replace aluminum that shows evidence of deterioration of factory-applied finishes or that found in materials or workmanship within specified warranty period. 1. Deterioration includes, but is not limited to, the following: a. Color fading more than 5 Hunter units when tested according to ASTM D 2244. b. Chalking in excess of a No. 8 rating when tested according to ASTM D 4214. c. Cracking, checking, peeling, or failure of paint to adhere to bare metal. 2. Warranty Period: 20 years from date of Substantial completion. PART 2 - PRODUCTS 2.1 PERFORMANCE REQUIREMENTS A. Delegated Design: Engage a qualified professional engineer, as defined in 014000 "Quality Requirements," to design aluminum-framed storefronts. B. General Performance: Comply with performance requirements specified, as determined by testing of aluminum-framed storefronts representing those indicated for this Project without failure due to defective manufacture, fabrication, installation, or other defects in construction. 1. Aluminum-framed entrances and storefronts shall withstand movements of supporting structure including, but not limited to, story drift, twist, column shortening, long-term creep, and deflection from uniformly distributed and concentrated live loads. 2. Failure also includes the following: a. Thermal stresses transferring to building structure. b. Glass breakage. c. Noise or vibration created by wind and thermal and structural movements. d. Loosening or weakening of fasteners, attachments, and other components. e. Failure of operating units. f. Deflection exceeding specified limits. g. Sealant failure. h. Framing members transferring stresses, including those caused by thermal and structural movement to glazing. GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS 084113 - 5 C. Structural Loads: 1. Wind Loads: As indicated on Drawings. 2. Other Design Loads: As indicated on Drawings. D. Deflection of Framing Members: At design wind pressure loads and seismic loads as indicated on the structural drawings, and as follows: 1. Deflection Normal to Wall Plane: Limited to edge of glass in a direction perpendicular to glass plane not exceeding 1/175 of the glass edge length for each individual glazing lite or an amount that restricts edge deflection of individual glazing lites to 3/4 inch, whichever is less. 2. Deflection Parallel to Glazing Plane: Limited to 1/360 of clear span or 1/8 inch, whichever is smaller. 3. Cantilever Deflection: Where framing members overhang an anchor point, as follows: a. Perpendicular to Plane of Wall: No greater than 1/240 of clear span plus 1/4 inch for spans greater than 11 feet 8-1/4 inches or 1/175 times span, for spans less than 11 feet 8-1/4 inches. E. Structural: Test according to ASTM E 330 as follows: 1. When tested at positive and negative wind-load design pressures, assemblies do not evidence deflection exceeding specified limits. 2. When tested at 150 percent of positive and negative wind-load design pressures, assemblies, including anchorage, do not evidence material failures, structural distress, or permanent deformation of main framing members exceeding 0.2 percent of span. 3. Test Durations: As required by design wind velocity, but not less than 10 seconds. F. Air Infiltration: Test according to ASTM E 283 for infiltration as follows: 1. Fixed Framing and Glass Area: a. Maximum air leakage of 0.06 cfm/sq. ft. at a static-air- pressure differential of 1.57 lbf/sq. ft. G. Water Penetration under Static Pressure: Test according to ASTM E 331 as follows: 1. No evidence of water penetration through fixed glazing and framing areas when tested according to a minimum static-air-pressure differential of 20 percent of positive wind- load design pressure, but not less than 6.24 lbf/sq. ft. H. Water Penetration under Dynamic Pressure: Test according to AAMA 501.1 as follows: 1. No evidence of water penetration through fixed glazing and framing areas when tested at dynamic pressure equal to 20 percent of positive wind-load design pressure, but not less than 6.24 lbf/sq. ft. 2. Maximum Water Leakage: According to AAMA 501.1. Water leakage does not include water controlled by flashing and gutters, or water that is drained to exterior. GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS 084113 - 6 I. Energy Performance: Certified and labeled by manufacturer for energy performance as follows: 1. Thermal Transmittance (U-factor): a. Fixed Glazing and Framing Areas: U-factor for the system of not more than 0.41 Btu/sq. ft. x h x deg F as determined in accordance with NFRC 100. b. Entrance Doors: U-factor of not more than 0.77 Btu/sq. ft. x h x deg F as determined in accordance with NFRC 100. 2. Solar Heat-Gain Coefficient (SHGC): a. Fixed Glazing and Framing Areas: SHGC for the system of not more than 0.25 as determined in accordance with NFRC 200. b. Entrance Doors: SHGC of not more than 0.25 as determined in accordance with NFRC 200. 3. Air Leakage: a. Fixed Glazing and Framing Areas: Air leakage for the system of not more than 0.06 cfm/sq. ft. at a static-air-pressure differential of 6.24 lbf/sq. ft. when tested in accordance with ASTM E283. b. Entrance Doors: Air leakage of not more than 1.0 cfm/sq. ft. at a static-air-pressure differential of 1.57 lbf/sq. ft.. 4. Condensation Resistance Factor (CRF): a. Fixed Glazing and Framing Areas: CRF for the system of not less than 55 as determined in accordance with AAMA 1503. b. Entrance Doors: CRF of not less than 57 as determined in accordance with AAMA 1503. J. Noise Reduction: Test in accordance with ASTM E90, with ratings determined by ASTM E1332, as follows. 1. Outdoor-Indoor Transmission Class: Minimum 34. K. Thermal Movements: Allow for thermal movements resulting from ambient and surface temperature changes: 1. Temperature Change: 120 deg F, ambient; 180 deg F, material surfaces. 2. Thermal Cycling: No buckling; stress on glass; sealant failure; excess stress on framing, anchors, and fasteners; or reduction of performance when tested according to AAMA 501.5. a. High Exterior Ambient-Air Temperature: That which produces an exterior metal- surface temperature of 180 deg F. GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS 084113 - 7 b. Low Exterior Ambient-Air Temperature: 0 deg F. c. Interior Ambient-Air Temperature: 75 deg F. L. Structural-Sealant Joints: 1. Designed to carry gravity loads of glazing. 2. Designed to produce tensile or shear stress of less than 20 psi. M. Structural Sealant: Capable of withstanding tensile and shear stresses imposed by structural- sealant-glazed storefront system without failing adhesively or cohesively. When tested for preconstruction adhesion and compatibility, cohesive failure of sealant shall occur before adhesive failure. 1. Adhesive failure occurs when sealant pulls away from substrate cleanly, leaving no sealant material behind. 2. Cohesive failure occurs when sealant breaks or tears within itself but does not separate from each substrate because sealant-to-substrate bond strength exceeds sealant's internal strength. 2.2 MANUFACTURERS A. Manufacturers: Subject to compliance with requirements, provide products by one of the following: 1. EFCO Corporation. 2. Kawneer North America; an Alcoa company. 3. YKK AP American, Inc. B. Source Limitations: Obtain all components of the aluminum-framed entrance and storefront system, including framing spandrel panels, entrances, sun control, and accessories, from single manufacturer. 2.3 FRAMING A. Framing Members: Manufacturer’s extruded- or formed-aluminum framing members of thickness required and reinforced as required to support imposed loads. 1. Construction: Thermally broken. 2. Glazing System: Retained mechanically with gaskets on four sides. 3. Glazing Plane: Front. 4. Finish: Exterior Storefront: a. Exterior Storefront: Match existing exterior storefront finish b. Interior Storefront: Clear Anodized 5. Fabrication Method: Field-fabricated stick system. GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS 084113 - 8 B. Backer Plates: Manufacturer's standard, continuous backer plates for framing members, if not integral, where framing abuts adjacent construction. C. Brackets and Reinforcements: Manufacturer's standard high-strength aluminumwith non-staining, nonferrous shims for aligning system components. D. Materials: 1. Aluminum: Alloy and temper recommended by manufacturer for type of use and finish indicated. a. Sheet and Plate: ASTM B 209. b. Extruded Bars, Rods, Profiles, and Tubes: ASTM B 221. c. Extruded Structural Pipe and Tubes: ASTM B 429/B 429M. d. Structural Profiles: ASTM B 308/B 308M. 2. Steel Reinforcement: Manufacturer’s standard zinc- r i c h , c o r r o s i o n - r e s i s t a n t primer c o m p l y i n g w i t h SSPC-PS Guide No. 12.00; applied immediately after surface preparation and pretreatment. Select surface preparation methods according to recommendations in SSPC-SP COM, and prepare surfaces according to applicable SSPC standard. a. Structural Shapes, Plates, and Bars: ASTM A 36/A 36M. b. Cold-Rolled Sheet and Strip: ASTM A 1008/A 1008M. c. Hot-Rolled Sheet and Strip: ASTM A 1011/A 1011M. 2.4 GLAZING A. Glazing: Comply with Section 08 8000 "Glazing." B. Glazing Gaskets: Manufacturer’s standard sealed-corner pressure-gl azing system of black, re silient elastomeric glazing gaskets, setting blocks, and shims or spacers. C. Glazing Sealants: As recommended by manufacturer. 1. Sealant shall have a VOC content of 250 g/L or less. D. Structural Glazing Sealan ts: ASTM C 1184, chemically curing s ilicone formulation that is compatible with system components with which it comes in contact, specifically formulated and tested for use as structural sealant and approved by structural-sealant manufacturer for use in storefront system indicated. 1. Color: As selected by the Architect from manufacturer’s full range of colors. E. Weatherseal Sealants: ASTM C 920 for Type S; Grade NS; Class 25; Uses NT, G, A, and O; chemically curing silicone formulation that is compatible with structural sealant and other system components with which it comes in contact; recommended by structural-sealant, weatherseal-sealant, and structural-sealant-glazed storefront manufacturers for this use. 1. Color: Match structural sealant. GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS 084113 - 9 F. Spacers and Setting Blocks: Manufacturer’s standard elastomeric type. 2.5 ACCESSORIES A. Fasteners and Accessories: Manufacturer's standard corrosion-resistant, non-staining, nonbleeding fasteners and accessories compatible with adjacent materials. 1. Use self-locking devices where fasteners are subject to loosening or turning out from thermal and structural movements, wind loads, or vibration. 2. Reinforce members as required to receive fastener threads. 3. Use of exposed fasteners is prohibited, except for application of hardware. 4. Use exposed fasteners with countersunk Phillips screw heads, fabricated from 300 series stainless steel. B. Anchors: Three-way adjustable anchors with minimum adjustment of 1 inch (25.4 mm) that accommodate fabrication and installation tolerances in material and finish compatible with adjoining materials and recommended by manufacturer. 1. Concrete and Masonry Inserts: Hot-dip galvanized cast-iron, malleable-iron, or steel inserts complying with ASTM A 123/A 123M or ASTM A 153/A 153M requirements. C. Concealed Flashing: Dead-soft, minimum 0.018-inch thick stainless steel, ASTM A 240/A 240M of type recommended by manufacturer. D. Bituminous Paint: Cold-applied asphalt-mastic paint complying with SSPC-Paint 12 requirements except containing no asbestos, formulated for 30-mil thickness per coat. E. Flashing: Manufacturer's standard 26 gauge corrosion-resistant, non-staining, nonbleeding flashing compatible with adjacent materials. Form exposed flashing from sheet aluminum finished to match framing and of sufficient thickness to maintain a flat appearance without visible deflection. F. Joint Sealants: For installation at perimeter of aluminum-framed systems, as specified in Section 079200 "Joint Sealers." G. Provide sealants for use inside of the weatherproofing system that have a VOC content of 250 g/L or less when calculated according to 40 CFR 59, Subpart D (EPA Method 24). 2.6 FABRICATION A. Form or extrude aluminum shapes before finishing. B. Weld in concealed locations to greatest extent possible to minimize distortion or discoloration of finish. Remove weld spatter and welding oxides from exposed surfaces by descaling or grinding. C. Fabricate components that, when assembled, have the following characteristics: GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS 084113 - 10 1. Profiles that are sharp, straight, and free of defects or deformations. 2. Accurately fitted joints with ends coped or mitered. 3. Physical and thermal isolation of glazing from framing members. 4. Accommodations for thermal and mechanical movements of glazing and framing to maintain required glazing edge clearances. 5. Provisions for field replacement of glazing from interior for vision glass and exterior for spandrel glazing or metal panels. 6. Fasteners, anchors, and connection devices that are concealed from view to greatest extent possible. 7. Means to drain water passing joints, condensation occurring within framing members, and moisture migrating within the system to exterior D. Storefront Framing: Fabricate components for assembly using shear-block system. E. After fabrication, clearly mark components to identify their locations in Project according to Shop Drawings. 2.7 ALUMINUM FINISHES A. High-Performance Organic Finish (Three-Coat Fluoropolymer): AA-C12C40R1x (Chemical Finish: cleaned with inhibited chemicals; Chemical Finish: conversion coatings; Organic Coating: manufacturer's standard three-coat, thermo-cured system consisting of specially formulated inhibitive primer, fluoropolymer color coat, and clear fluoropolymer topcoat, with both color coat and clear topcoat containing not less than 70 percent flouropolymer resin by weight). Prepare, pretreat, and apply coating to exposed metal surfaces to comply with AAMA 2605 and with coating and resin manufacturers' written instructions. 1. Color and Gloss: Custom color as selected by Architect. 2.8 SOURCE QUALITY CONTROL A. Structural Sealant: Perform quality-control procedures complying with ASTM C 1401 recommendations including, but not limited to, assembly material qualification procedures, sealant testing, and assembly fabrication reviews and checks. PART 3 - EXECUTION 3.1 EXAMINATION A. Examine areas, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of the Work. B. Proceed with installation only after unsatisfactory conditions have been corrected. GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS 084113 - 11 3.2 PREPARATION A. Prepare surfaces that are in contact with structural sealant according to sealant manufacturer's written instructions to ensure compatibility and adhesion. Preparation includes, but is not 3.3 INSTALLATION A. General: 1. Comply with manufacturer's written instructions. 2. Do not install damaged components. 3. Fit joints to produce hairline joints free of burrs and distortion. 4. Rigidly secure nonmovement joints. 5. Install anchors with separators and isolators to prevent metal corrosion and electrolytic deterioration and to prevent impeding movement of moving joints. 6. Seal perimeter and other joints watertight unless otherwise indicated. 7. Verify conduit for electronic hardware is open and has not been damaged or crimped that would impede concealed wiring required for specified hardware B. Metal Protection: 1. Where aluminum is in contact with dissimilar metals, protect against galvanic action by painting contact surfaces with materials recommended by manufacturer for this purpose or by installing nonconductive spacers. 2. Where aluminum is in contact with concrete or masonry, protect against corrosion by painting contact surfaces with bituminous paint. 3. Install components to drain water passing joints, condensation occurring within framing members, and moisture mitigating within the system to exterior. C. Set continuous sill members and flashing in full sealant bed as specified in 079200 "Joint Sealants" to produce weathertight installation. D. Install components plumb and true in alignment with established lines and grades. E. Install operable units level and plumb, securely anchored, and without distortion. Adjust weather-stripping contact and hardware movement to produce proper operation. F. Install glazing as specified in 088000 "Glazing." G. Install weather seal sealant according to 079200 "Joint Sealants" and according to sealant manufacturer's written instructions to produce weatherproof joints. Install joint filler behind sealant as recommended by sealant manufacturer. 3.4 ERECTION TOLERANCES A. Erection Tolerances: Install aluminum-framed storefronts to comply with the following maximum tolerances: GODWIN - VIRGINIAN PILOT BUILDING PROJECT 10015069.02 RENOVATION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS 084113 - 12 1. Plumb: 1/8 inch in 10 feet; 1/4 inch in 40 feet. 2. Level: 1/8 inch in 20 feet; 1/4 inch in 40 feet. 3. Alignment: a. Where surfaces abut in line or are sep arated by reveal or protruding element up to 1/2 inch wide, limit offset from true alignment to 1/16 inch. b. Where surfaces are separated by reveal or protruding element from 1/2 to 1 inch wide, limit offset from true alignment to 1/8 inch. c. Where surfaces are separated by reveal or protruding element of 1 inch wide or more, limit offset from true alignment to 1/4 inch. d. Where surfaces meet at corners, limit offset from true alignment to 1/32 inch. e. Diagonal measurements: Limit difference between diagonal measurement to 1/8 inch. 4. Location: Limit variation from plane to 1/8 inch in 12 feet; 1/2 inch over total length. 3.5 FIELD QUALITY CONTROL A. Clean the completed system, inside and out, promptly after installation and immediately before requesting Substantial Completion, exercising care to avoid damage to coatings. B. Clean glass surfaces after installation, complying with requirements contained in Section 088000 “Glazing” for cleaning and maintenance. Remove excess glazing and sealant compounds, dirt and other substances from aluminum surfaces. 3.6 PROTECTION A. Institute protective measures required throughout the remainder of the construction period to ensure that aluminum storefront will be without damage or deterioration, other than normal weathering, at time of Substantial Completion. END OF SECTION 084113 ),567)/225   6(&21')/225   1(,*+%25,1*%8,/',1*  7<37<3 $ $ 72'(&.       “/) “/)  “/) “/)  “/) “/) ),567)/225   6(&21')/225     %  72'(&.   ' $ ),567)/225   6(&21')/225   1(,*+%25,1*%8,/',1*6) 6) 6) 6) 6) 6)      7<3 $ ' $ $ 72'(&.     7<3 “/)  “/)   “/)  “/) $ $ % 6)6)6)         &/&/&/ &/          (((   (  (;  $ $ ' $         “/) “/)  5()(5726+((7 $$1' $)257<3,&$/6725()5217(/(9$7,216$1' '(7$,/6  5()(5726+((7 $)25*/$=,1*/(*(1'  5()(5726+((7 $$$1' $)25'2256&+('8/($1''(7$,/6  3529,'()/$6+,1* &2817(5)/$6+,1*$7$//(;7(5,2523(1,1*6   35(6685(:$6+$//35(&$67&21&5(7($1'81'(56,'(2)(;,67,1*  &$123<213/$1($670$,167 ,17(5,25*/$6635,9$&<),/0 *) &/($5,168/$7,1**/$66 7<3$7(;7(5,25812 )/2$7*/$66 7<3$7,17(5,25812 %$//,67,&),/0 *) &20%,1$7,212)%$//,67,&),/0$33/,('72,17(5,25 6,'(2)*/$66 *) $1'35,9$&<),/0$33/,('72 (;7(5,256,'(2)*/$66 *) $5&+,7(&785( (1*,1((5,1* *(263$7,$/ɕɕ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“ 62/,'685)$&(:,1'2:6722/ %5,&.9(1((5$7 6725()52176) :%5,&.7,(6#2& 9(572& &08:+25,=-2,17 5(,1)#2&9(57 07/)855,1*675,36 720$7&+(;,67,1* *:% %$6($66&+('8/(' 67((//,17(/6((6758&785$/'5$:,1*6 %5,&.9(1((5 &2856(6 (;,67,1*%5,&.9(1((5 $/80,1806725()5217 6+,0$1'%$&.(552' %27+6,'(6 $/80,1806,//)/$6+,1* (;,67,1*%5,&.9(1((5$1' (;,67,1*&08$76) 07/)855,1*675,36 720$7&+(;,67,1**:% (;,67,1*)/2256/$% $ ' (;,67,1*&08  6&+('8/('0$18$/52//(5 6+$'(6$/,*1)5217)$&(2) )$6&,$:,7++($'(5$%29( )/8,'$33/,('9$325 3(50($%/($,5%$55,(5  &217,182866($/$17 &217,18286:'%/2&.,1* ),567)/225   %5,&.9(1((5720$7&+ $'-$&(17,17(5,25 &216758&7,21 (;,67,1*:$//&216758&7,21 (;,67,1*)/2256/$% “  “ (;7(5,25%5,&.9(1((5 %5,&.9(1((5 :%5,&.7,(6#2& 9(572& &08:+25,=-2,17 5(,1)#2&9(57 ),567)/225    “ 07/)855,1*675,36 720$7&+(;,67,1* *:% (;,67,1*)/2256/$% (;,67,1*%5,&.9(1((5 &08:+25,=-7 5(,1)#2&9(57 %5,&.9(1((5 :%5,&.7,(6#2& 9(572& “ 7223(1,1*      7+58(<(%2/7: &2035(66,216/((9( $1':$6+(56((6758&785$/ '5$:,1*6 (;,67,1*&08(;,67,1*%5,&.9(1((5 35((1*,1((5(' 35(0$18)07/&$123<   *5287&(//62/,' 7+58(<(%2/7: &2035(66,216/((9( $1':$6+(56((6758&785$/ '5$:,1*6 (;,67,1*$/80,1806725()5217 6&+('8/('&(,/,1* 6((5()/(&7('&(,/,1*3/$1 07/678'6#2& *:% 6(((/(9$7,21'$ )25%277202)&$123< (/(9$7,216 ),567)/225   “      67((//,17(/6((6758&785$/'5$:,1*6 %5,&.9(1((5 &2856(6 (;,67,1*%5,&.9(1((5 07/)855,1*675,36 720$7&+(;,67,1* *:% (;,67,1*%5,&.9(1((5 (;,67,1*&08 $/80,1806725()5217 6+,0$1'%$&.(552' %27+6,'(6 $/80,1806,//)/$6+,1* 07/)855,1*675,36 720$7&+(;,67,1**:% %$6($66&+('8/(' (;,67,1*)/2256/$% $ ' 6,012 52//(5 6+$'( &217,18286:'%/2&.,1* ),567)/225   “ %5,&.9(1((5 &2856(6 (;,67,1*%5,&.9(1((5 (;,67,1*&08 67((//,17(/6(( 6758&785$/'5$:,1*6 07/)855,1*675,36 720$7&+(;,67,1**:% 67((//,17(/3/$7( 6((6758&785$/'5$:,1*6 6($/$17$1'%$&.(552' %27+6,'(6 )/(;,%/(7+58:$// )/$6+,1*)250(1''$06 ($&+6,'(2)23(1,1* )/8,'$33/,('9$325 3(50($%/($,5%$55,(5 660(7$/'5,3:,7+ :((36$72& &08623(,1),//:,7+ :(/'('7,(6#2& $'')855,1**<3$1'&(,/,1* 6+,0 (;,67,1*6/$% (;,67,1*&$123<6758&785( (;,67,1*%5,&.9(1((5  (;,67,1*&$123<522),1*6<67(0 $&5</,&3/$67(5),1,6+6<67(021),%(5*/$660$7 )$&('6+($7+,1*210(7$/+$7&+$11(/6#2& 210(7$/&+$11(/6#2& 9(17('62)),75(9($/$//6,'(6)5<5(*/(7 '50)925(48$/35(),1,6+(':+,7( (;,67,1*&$123<)$6&,$  “ 9(17('62)),75(9($/$//6,'(6)5<5(*/(7'50)925(48$/35(),1,6+(':+,7( $5&+,7(&785( (1*,1((5,1* *(263$7,$/ɕɕ &25325$7,21/$1( 68,7( 9,5*,1,$%($&+9$   $ % & ' ( 6+((71$0( 352-(&712 '$7(,668(' 6+((712 '(6,*1('%< '5$:1%< &+(&.('%<,668$1&(6&+('8/( 180%(5'$7('(6&5,37,21 3+$6(),567)/2255(129$7,21  $XWRGHVN'RFV6XIIRON9$&LW\3URMHFWV+8%B%B5*RGZLQ9LUJLQLDQ3LORWB5HQRB$5&+B5UYW $0 :$//6(&7,216 $ $*(181* 0,-$/0,//(5 .%$5.(5  *2':,1 9,5*,1,$13,/27%8,/',1* &,7<2)68))2/.9$ 10$,16768))2/.9$   $ :$//6(&7,21   $ :$//6(&7,21   $ :$//6(&7,21$76+$)7   ' 7<30$3(6&$123<,167$//$7,21'(7$,/   $ :$//6(&7,21   $ :$//6(&7,21  'DWH 5HYLVLRQ   ' &$123<'(7$,/ /LF1R 12/05/2025 1(,*+%25,1*%8,/',1* 1(,*+%25,1*%8,/',1* $5&+,7(&785( (1*,1((5,1* *(263$7,$/ɕ ɕ *2':,19,5*,1,$13,/27%8,/',1* 10$,16768))2/.9$         *5$3+,&6&$/(    ($67(/(9$7,21    1257+(/(9$7,21    6287+(/(9$7,21    :(67(/(9$7,21 NORTH, SOUTH AND WEST WALLS BRICK PAINT NEW STOREFRONT FRAMES & MULLIONS PAINTED HISTORIC DISTRICT PPG NEW ENGLAND COLLECTION BLACK MAGIC TO MATCH EXISTING 11" ASH 15" ASH 14" ASH 12" ASH 11" FLOWERING METAL POST MULCH MULCH MULCH MULCH NORTHSARATOGA STREET NORTHSARATOGA STREET (4) FLEX POSTS 5' POST ANDCHAIN FENCE METAL POST STUB 30" OAK METAL LP BASE 6' CLF METAL HANDRAIL 4' POST AND CHAIN FENCE, DAMAGED CONC. WHEELSTOP (TYP.) 02 02 01 03 04 05 06 07 08 09 10 11 12 13 13 14 15 16 02 FORMERVIRGINIAN-PILOT BUILDING METAL HANDRAIL 07 07 "NEW JOINT ALLEY" PERPETUAL INGRESS/EGRESS EASEMENT D.B. 44 PG 96 APPROX. LOCATIONEXISTING DRAINAGE EASEMENT DB. 16 PG 210 PARCELS (02) AND (10) ARE SUBJECT TO A WALL AGREEMENT CREATED IN DB. 16 PG 107 THE RIGHT TO USE PARCEL (09) SUBJECT TO A PERPETUAL DRAINAGE EASEMENT AS DESCRIBED IN D.B. 25 PG 136. DESCRIPTION INSUFFICIENT TO SHOW EASEMENT GRAPHICALLY THE RIGHT TO USE INCOMMON (WITH OTHERS)FOR PURPOSES OF INGRESSAND EGRESSINST. #000108410CONDOMINIUM DECLARATIONINST. #070165590 PARCEL (07) SUBJECT TO A CITY OF SUFFOLK STORM DRAINAGE EASEMENT AS DESCRIBED IN D.B. 53 PG 519. DESCRIPTION INSUFFICIENT TO SHOW EASEMENT GRAPHICALLY SEE INSET THE RIGHT TO USE IN COMMON(WITH OTHERS) FOR PURPOSESOF INGRESS AND EGRESSINST. #000108410CONDOMINIUM DECLARATIONINST. #070165590 VA PILOT BUILDING RENOVATION PREPARED FOR WOOLPERT SITE PLAN CS100 © NORTH LEGEND LIMITS OF DISTURBANCE PROPERTY LINE SIDEWALK CONCRETE INTERSECTION SIGHT TRIANGLE PAVEMENT LEGEND STANDARD - DUTY ASPHALT 2" SURFACE ASPHALT VDOT SM-12.5A 8" AGGREGATE BASE VDOT 21-A COMPACTED TO A DRY DENSITY OF AT LEAST 100% OF THE STANDARD PROCTOR MAXIMUM DRY DENSITY. COMPACTED SUBGRADE HEAVY - DUTY ASPHALT 2" SURFACE ASPHALT VDOT SM-12.5A 3" INTERMEDIATE ASPHALT VDOT BM-25.0A 8" AGGREGATE BASE VDOT 21-A COMPACTED TO A DRY DENSITY OF AT LEAST 100% OF THE STANDARD PROCTOR MAXIMUM DRY DENSITY. COMPACTED SUBGRADE VDOT CG-2 CURB VDOT CG-6 CURB AND GUTTER VDOT CG-12 DETECTABLE WARNING SURFACE NOTES 1. ALL PARKING STALLS SHALL BE 9'X18'. CONCRETE ENTRANCE PAVED FLUME DETAIL NOTE: WIPEDOWN FULL CURB TO BE FLUSH WITH FINISH GRADE. SEE SHEET CG100. VA PILOT BUILDING RENOVATION PREPARED FOR WOOLPERT SITE PLAN DETAILS CS500 © PARKING LOT STRIPING DETAILS ACCESSIBLE PARKING SYMBOL ACCESSIBLE PARKING STALLS WHEEL STOP CONSTRUCTION STANDARDS ● ● ● ● ● ● TYPICAL BOLLARD DETAIL ACCESSIBLE PARKING SIGN ROADWAY PAVEMENT MARKINGS PAVED FLUME DETAIL VDOT CG2VDOT CG2 NOTE: WIPEDOWN FULL CURB TO BE FLUSH WITH FINISH GRADE. SEE SHEET CG100. 11" ASH 15" ASH 14" ASH 12" ASH 11" FLOWERING ELECT ELECTRIC BOX ELECTRIC BOX BACKUP GENERATORON PLASTIC PAD METAL POST MULCH MULCH MULCH MULCH NORTHSARATOGA STREET NORTHSARATOGA STREET (4) FLEX POSTS 5' POST ANDCHAIN FENCE SAN #01 UPSTREAMSTRUCTURENOT FOUND METAL POST STUB 30" OAK METAL LP BASE UC CONDUITS ENTERING GROUND (2) LP #5 TPED #R/139TPED NO # TPED #R/157 QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLD QLD QLD QLD QLD QLD QLD QLD QLD QLD QLD QLD QLC QLC QLC QLD QLDQLC QLD QLD 6' CLF METAL HANDRAIL 4' POST AND CHAIN FENCE, DAMAGED CONC. WHEELSTOP (TYP.) SCO SCO LP #XA63 LP #XA71 LP #XO69 METERS, (5)METERS, (3) QLC QLC QLD QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLCQLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC QLC 8" VCP, QLD TPED NO # QLD QLD QLD QLC QLD QLD QLD QLD QLD QLD QLD QLD QLD QLD QLD QLD QLD QLD 02 02 01 03 04 05 06 07 08 09 10 11 12 13 13 14 15 QLC QLC 16 PL5 (DEED) S67°19'38"W 102.30' (PLAT) PL9 (DEED) SOUTHWARDLY 27' 6" (DEED) NORTHWARDLY 26' 6" (DEED) PL11(DEED) N68°32'W 48.00' (PLAT) PL28 (DEED) 125.6' BUILDING (PLAT) PROPERTY LINE PER GIS 18.5' (PLAT) PL2 (PLAT) PL3 (DEED) PL4(PLAT) N31°30'30"E 72.51' (DEED) NORTHWAR (DEED) SOUTHWARDLY 33' (DEED) QLC N22°09'26"E 59.50' (PLAT) 02 N67°26'12"W 189.90' (PLAT) N21°09'15"E 36.96'(PLAT) N67°33'45"W 117.54' (DEED) PL12 (DEED) N67°33'45"W 131.85' (DEED) 7.30' (PLAT) S67°34'02" S22°31'06"W 70.60' (DEED) WESTWARDLY 110' (DEED)S67°00'30"E 106.15' (DEED) ASTWARDLY 110' (DEED) 07.58' (DEED) N (189.90') FORMERVIRGINIAN-PILOT BUILDING (S23°27'02"W) (65.05') (S23°2 N67°22'12"W 189.58' (PLAT) S23°18'W 48.00' (DEED) PL10 (PLAT) METAL HANDRAIL 07 07 NORTHERLY 48' (DEED) EASTERLY 222' +/- (DEED) SOUTHERLY 48' (DEED) PROPERTY LINESABANDONED BY D.B. 44 PG 96 SEE ALSO P.B. 3 PG 132 "NEW JOINT ALLEY" PERPETUAL INGRESS/EGRESS EASEMENT D.B. 44 PG 96 5.40' (PLAT) APPROX. LOCATIONEXISTING DRAINAGE EASEMENT DB. 16 PG 210 PARCELS (02) AND (10) ARE SUBJECT TO A WALL AGREEMENT CREATED IN DB. 16 PG 107 WESTERLY APPROX. 131' (DEED) PL13 (DEED) NORTHERLY 34' +/- (DEED) N66°48'28"W 118.22' (PLAT) S23°19'43"W 47.30' (PLAT) PL14 (PLAT) NORTHERLY 47.30' (DEED) EASTERLY 118.06' (DEED) PL15 (DEED) SOUTHERLY APPROX. 96.94' (DEED) NORTHERLY 39.50' (DEED) PL17 (DEED) PL18 (PLAT) S23°19'43"W 39.50' (PLAT) 126.2' +/-(PLAT) S23°19'43"W 65.0' (PLAT) PL19 (PLAT) PL20 (DEED) PL22 (PLAT) PL21 (DEED) 5.14'(PLAT) PL23 (DEED) PL24 (DEED) WESTWARDLY 83' (DEED) PL25(PLAT) NORTHERLY 34' (DEED) N23°19'43"E 34.22' (PLAT) S66°21'33"E 189.90' (PLAT) 190.7' BUILDING (PLAT) 14.6' (PLAT) 22.9' (PLAT) PROPERTY LINE PER GIS THE RIGHT TO USE PARCEL (09) SUBJECT TO A PERPETUAL DRAINAGE EASEMENT AS DESCRIBED IN D.B. 25 PG 136. DESCRIPTION INSUFFICIENT TO SHOW EASEMENT GRAPHICALLY THE RIGHT TO USE INCOMMON (WITH OTHERS)FOR PURPOSES OF INGRESSAND EGRESSINST. #000108410CONDOMINIUM DECLARATIONINST. #070165590 SAN MANHOLE NOT FOUNDDURING FIELD EFFORTS.APPROX. LOCATIONSHOWN PER GIS DATARECEIVED FROM SUFFOLKPUBLIC UTILITIES PL6 (DEED) PARCEL (07) SUBJECT TO A CITY OF SUFFOLK STORM DRAINAGE EASEMENT AS DESCRIBED IN D.B. 53 PG 519. DESCRIPTION INSUFFICIENT TO SHOW EASEMENT GRAPHICALLY N6 N67°19'38"W 102.30' (DEED) PL26 (DEED) PL27 (DEED) 64.7' BUILDING (PLAT) PL26 (DEED) QLC SEE INSET THE RIGHT TO USE IN COMMON(WITH OTHERS) FOR PURPOSESOF INGRESS AND EGRESSINST. #000108410CONDOMINIUM DECLARATIONINST. #070165590 QLB B A QLB QLB A = UNIDENTIFIED UTILITY PAINT,SUSPECTED ABANDONEDTELECOMMUNICATIONS LINE B = UNIDENTIFIED UTILITY PAINT,SUSPECTED SANITARYSEWER LINE QLB 6" PVC PIPE,SUSPECTED SCO PL1 (DEED)STM #11 METALTROUGH STM #05 CONC. CONC. STM #06 CONC. STM #07 IRON CONC. STM #08 CONC. STM #09 CONC. W/ SLEEVESTM #10 CONC. O/S CONC. STM #12STM #13 CONC.CONC. CONC. METAL PLATE OVER STM. JUNCTION CONC. DIP STM #14 CONC. STM #15 CONC. 20 sf - SH 20 sf - SH 20 sf - SH 20 sf - SH 20 sf - SH 20 sf - SH 20 sf - SH 17 - LL 62 sf - SH 32 - LL 121 sf - SH 74 sf - SH 20 - LL (224 sf) SH (1) QA (2) QA (2) QA (1) QA (1) QA (1) QA (4) AG (16) IC SYMBOL CODE QTY BOTANICAL NAME COMMON NAME ROOT CAL. TREES AG 4 ACER RUBRUM `OCTOBER GLORY` TM OCTOBER GLORY MAPLE B & B 1.5"-2" CAL. MIN. QA 8 QUERCUS ACUTISSIMA SAWTOOTH OAK B&B 1.5"-2" CAL. MIN. SYMBOL CODE QTY BOTANICAL NAME COMMON NAME ROOT SIZE SHRUBS IC 16 ILEX CORNUTA `BURFORDII NANA` DWARF BURFORD HOLLY CONT. 24" HT. MIN SYMBOL CODE QTY BOTANICAL NAME COMMON NAME CONT SPACING SPACING GROUND COVERS LL 69 LIRIOPE MUSCARI `BIG BLUE BIG BLUE LILY TURF 1 GAL 24" o.c. SEED 3,774 SF SEED TURF SEED SEED SH 701 SF SHREDDED HARDWOOD MULCH BULK PLANT SCHEDULE VA PILOT BUILDING RENOVATION PREPARED FOR WOOLPERT PLANTING PLAN CP100 © NORTH VA PILOT BUILDING RENOVATION PREPARED FOR WOOLPERT PLANTING PLAN DETAILS CP500 © 3" 1" 5" PLANTING BED TRENCH EDGING NOTE: 1. TRENCH EDGE SHALL BE LOCATED BETWEEN PLANTING BED AND ALL TURF / SOD AREAS. 2. MAINTAIN POSITIVE DRAINAGE IN ALL PLANTING BEDS. 3. SEE NOTES THIS SHEET FOR TYPE OF MULCH. MULCH 3" DEPTH ® PLANTING SPECIFICATIONS 1. SOILS TESTING A.All soil testing shall be done at the contractor's expense. soil tests shall be conducted by a state laboratory or recognized commercial laboratory. each sample shall be extracted from a six-inch deep core and prepared in accordance with recommendations of the soil-testing laboratory. B.each soils test shall determine soil texture / particle size, organic matter (OM), soil pH, buffer pH, nitrogen (N), phosphorus (P), potassium (K), calcium (Ca), iron (Fe), boron (B), zinc (Zn), copper (Cu), magnesium (Mg), manganese (Mn), sulfur (S), sodium (Na), calculated cation exchange capacity (CEC), excess carbonate, electrical conductivity (EC) and total dissolved solids (TDS), sodium adsorption ratio (SAR), AND soluble salts. C.All new soils provided from off-site sources, obtain one soil test for each soil source per 500 cubic yards of soil and submit soil test results and soil amendment recommendations to to the owner and engineer of record for review and acceptance prior to distributing and amending soil. D.For all existing stockpiled topsoil to be redistributed on site, obtain one soil test per 500 cubic yards of soil prior to application. submit soil test results and soil amendment recommendations to the owner and engineer of record for review and acceptance prior to redistributing and amending soil. 2. DELIVERY, HANDLING, AND STORAGE: D. Deliver packaged materials in manufacturer's unopened containers or bundles, fully identified with name, brand, type, weight, and analysis. Store packaged materials in such a manner as to prevent damage or intrusion of foreign matter. E. Dig balled and burlapped (B& B) plants with firm, natural balls of earth, of a diameter not less than recommended by the American Standard for Nursery Stock, and of sufficient depth to include the fibrous and feeding roots. B&B plants will not be accepted if the ball is cracked or broken before or during planting operation. F. Deliver trees and shrubs after preparations for planting have been completed. Do not bend, bind, or tie trees or shrubs in such a manner as to damage bark, break branches or destroy natural shape. If planting is delayed more than 6 hours after delivery, set trees and shrubs in shade, protect from weather and mechanical damage, and keep roots moist by heeling-in bare root stock and covering plant balls with soil, peat moss or other acceptable material for balled stock. Plants shall be kept well watered and shall not remain unplanted for longer than ten (10) days after delivery. G. Plants shall be lifted and handled from the bottom of the ball only. H. Do not remove container-grown stock from containers until planting time. 3. DRAINAGE: Before planting, determine that areas to receive plant material have adequate subdrainage. A. The landscape contractor is responsible for drainage tests as necessary to identify any problems prior to beginning planting operations. Upon commencement of planting operations the landscape contractor assumes responsibility for soil conditions. B. Dig planting pits to full depth and dimensions indicated on drawings. C. At bottom of planting pit, excavate rectangular pit 12 inches by 12 inches by 18 inches deep. Quickly pour water into pit to a depth of 6 inches (approximately 3-3 3/4 gallon). Note time required for water to be completely absorbed. Divide time noted by 6 to achieve average rate of absorption for 1 inch of water. Where rate of absorption exceeds 60 minutes per inch, notify owner immediately for directions on how to proceed. 4. PLANTING DATES: Planting shall be done only within the following dates except as approved by Owner. A. Deciduous and Evergreen Trees, Shrubs, and Vines: October 1 to May 31 for un-irrigated sites except when the ground is frozen during the winter months. B. Planting of Deciduous and Evergreen Trees, Shrubs, and Vines during the months of June, July, August, and September is restricted to sites that have automated irrigation systems. C. All plant material shall be guaranteed by the Contractor for a period of 1 year from the date final acceptance to be in good, healthy and flourishing condition. 5. MATERIALS FOR PLANTING: A. Topsoil: shall be a fertile, friable natural loam, uniform in composition, free of stones, lumps, plants and their roots, debris and other extraneous matter over 1 inch in diameter, capable of sustaining vigorous plant growth. Soil shall be harvested at a single source from the O and/or A horizons of the soil profile. 1) Topsoil shall have a pH range of 5.5 to 7.5. 2) Topsoil shall contain 1.5-5% organic matter by dry weight . 3) Soil Texture: sandy loam, sandy clay loam with the following particle size distribution: Gravel Less than 10% Silt 15-30% Clay 20-35% Chemical Levels shall be: Magnesium Mg100+ units Phosphorus P205 150+ units Potassium - K20 120+ units 4) Soluble Salts/ Conductivity - Not to exceed 900 ppm/0.9 mmhos/cm (in soil); not to exceed 3000 ppm/2.5 mmhos/cm (in high organic mix) 5) Cation exchange capacity shall be a minimum of 8 meq/100g. B. Clay Loam to Sandy Clay Loam Soil: shall be a fertile, friable natural loam, uniform in composition, free of stones, lumps, plants and their roots, debris and other extraneous matter over 1 inch in diameter, capable of sustaining vigorous plant growth. 1) Soil shall have a pH range of 5.5 to 6.5. 2) Soil shall contain 2-5% organic content by volume. 3) Soil Texture: Clay loam to sandy clay loam with the following particle size distribution: Gravel Less than 10% Sand 20-50% Silt <35%% Clay 20-40% 4) Chemical Levels shall be: Magnesium Mg100+ units Phosphorus P205 150+ units Potassium - K20 120+ units 5) Soluble Salts/ Conductivity - Not to exceed 900 ppm/0.9 mmhos/cm (in soil); not to exceed 3000 ppm/2.5 mmhos/cm (in high organic mix) 6) Cation exchange capacity shall be 20-35 meq/100g. C. Compost: Compost shall be mature, stable, weed free, and produced by aerobic decomposition of organic matter. Compost feedstock shall be plant matter, such as high lignin forestry products or yard waste (leaves, brush and yard trimmings). 1) The product must not contain any visible refuse or other physical contaminants, substances toxic to plants, or over 5% sand, silt, clay or rock material by dry weight. 2) Compost shall be sampled and tested as required by the Seal of Testing Assurance Program of the United States Composting Council (USCC) and shall meet the physical requirements for compost as determined by USCC. 3) The product shall possess no objectionable odors. The product must meet all applicable USEPA CFR, Title 40, Part 503 Standards for Class A biosolids. 4) The moisture level shall be such that no visible water or dust is produced when handling the material. D. Composted Pine Bark Fines: Shall be approved composted, ground pine bark having no particle with a dimension greater than 3/4 inch. No more than 10% shall be wood. E. Sand: Shall be quartz based sharp concrete sand, ASTM C-33 Fine Aggregate, with a Fines Modulus Index between 2.8 and 3.2. F. Perlite: Coarse horticultural grade expanded, volcanic perlite. Maximum density shall be 8 lb./ft3. 1) pH shall be 6.5 to 7.5. 2) Perlite shall be meet the Perlite Institute's Standards for Gradation for Horticultural Perlite for Coarse Perlite with no more than 70% passing through a #16 Standard Sieve. G. Humus: Shall be mature, stable, weed free, and produced by aerobic decomposition of organic matter. Compost feedstock shall be plant matter, such as high lignin forestry products or yard waste (leaves, brush and yard trimmings). 1) Humus shall have a pH between 6 and 7.5. 2) Soluble Salt Concentration shall be less than 10dS/m. 3) Cation exchange capacity rate shall be 100-250. 4) The product must not contain any visible refuse or other physical contaminants, substances toxic to plants, or over 5% sand, silt, clay or rock material by dry weight. 5) The product shall possess no objectionable odors. The product must meet all applicable USEPA CFR, Title 40, Part 503 Standards for Class A biosolids. 6) The moisture level shall be such that no visible water or dust is produced when handling the material. H. Trace Elements: Shall be commercially available slow release materials containing zinc (Zn), Molybdenum (Mo), Copper (Cu), Boron (B), and Magnesium (Mn). I. Fertilizer: A commercial fertilizer for ornamental trees, shrubs and ground cover with an analysis of 10% Nitrogen, 6% Phosp horus and 4% Potassium shall be used. This fertilizer shall be granular with a minimum of 50% of the total Nitrogen in organic form. 14-14-14-Osmocote (or approved equal) shall be applied at a rate of 10 lbs. per square foot, tilled to a depth of 8 inch, shall be used for perennials. 6. PLANT MATERIALS: (Refer to the PLANT LIST on the drawings for specific types and quantities of plants): A. Plants shall be nursery grown in accordance with good horticultural practices. Plants shall either be obtained from local nurseries and/or others, which have soil and climatic conditions similar to those in the locality of the project. B. Plants shall be true to species and variety and unless specifically noted otherwise, all plants shall be of specimen quality, exceptionally heavy, symmetrical, tightly-knit plants, so trained or favored in their development and appearance as to be superior in form, number of branches, compactness and symmetry. C. Plants shall be sound, healthy and vigorous, well branched and densely foliated when in leaf, free of disease, insect pests, eggs or larvae and shall have healthy, well-developed root systems. They shall be free from physical damage or any conditions that would prevent thriving health and the desired appearance. D. Trees, which have a damaged or crooked leader, or multiple leaders, unless specified in the plant list, will be rejected. Trees with abrasion of the bark, sun scald, disfiguring knots, or pruning cuts more than 1 1/4 inch diameter which have not completely callused, will be rejected. E. Plants shall conform to measurements specified in the plant schedules except that plants larger than specified may be used if acceptable to the Landscape Architect or owner. Use of such plants shall not increase the contract price. If larger plants are accepted, the root ball shall be sized for the larger plant. F. Caliper Measurement: Shall be taken at a point on the trunk 6 inches above natural ground line for trees up to 4 inches diam eter, and at a point 12 inches above the natural ground line for trees over 4 inches diameter. G. Plants shall be measured when branches are in the normal position. Height and spread dimensions specified refer to the main body of the plant and not from branch tip to tip. 7. SOIL MIXING PROCEDURES: A. Topsoil used in sand/soil mixes shall be screened or shredded prior to mixing in sands. Maximum clod inclusion for soil mixes shall not exceed: Clod size (largest dimension) % of the soil mix volume Less than 1” Unlimited 1 to 3 inches 20% 3 to 6 inches 5% >6 inches Less than 2% A. Source material and soil mix stockpiles shall be protected from rain by covering with filter cloth. 8. INSPECTION: A. EXAMINE THE AREAS AND CONDITIONS WHERE SOIL MIX IS TO BE INSTALLED AND NOTIFY THE ENGINEER OF CONDITIONS DETRIMENTAL TO THE PROPER AND TIMELY COMPLETION OF THE WORK. DO NOT PROCEED WITH THE WORK UNTIL UNSATISFACTORY CONDITIONS ARE CORRECTED TO PERMIT PROPER INSTALLATION OF THE WORK. B. COOPERATE WITH OTHER CONTRACTORS AND TRADES WORKING IN AND ADJACENT TO OTHER WORK AREAS. EXAMINE DRAWINGS WHICH SHOW DEVELOPMENT OF ENTIRE PROJECT AND BECOME FAMILIAR WITH SCOPE OF OTHER WORK REQUIRED. 9. SOIL INSTALLATION - GENERAL PROCEDURES: G. IF SUBGRADE SOIL COMPACTION EXCEEDS 80%, EXISTING SOIL SHALL BE RIPPED TO A DEPTH OF 12 INCH TO ALLEVIATE COMPACTION WHICH HAS TAKEN PLACE DURING CONSTRUCTION. PRIOR TO LOOSENING OF SOIL, CONTRACTOR MUST LOCATE EXISTING UTILITIES AND COORDINATE WITH OWNER OR OWNERS REPRESENTATIVE ANY UNDERGROUND ELECTRIC LINES, DRAINAGE PIPES, CONDUITS, ETC. H. PREPARE THE SUBGRADE BY ROUGHENING THE TOP 3” OF THE SUBSOIL BY DRAGGING THE TEETH OF A BACKHOE BUCKET ACROSS THE SURFACE. I. BEGIN SOIL INSTALLATION AS SOON AS SUBSOIL IS PREPARED. USE LOW IMPACT EQUIPMENT WITH TRACK BELTS, LARGE TIRES, OR LOW TIRE PRESSURE TO LOWER COMPACTION AND SOIL DAMAGE DURING INSTALLATION. J. MONITOR COMPACTION DURING INSTALLATION AND LOOSEN SOILS AS NEEDED IF COMPACTION EXCEEDS 80%. 10. SOIL INSTALLATION - GENERAL PROCEDURES CONTINUED: K. Install specified soil in 12”-18” thick lifts. Compact each lift sufficiently to reduce settling but not enough to prevent the movement of water and feeder roots through the soil. The soils in each lift should feel firm to the foot in all areas and make only slight heel prints. 11. INSTALLATION OF SOIL MIX FOR LAWN AREAS ON GRADE: A. Soil Mix for Lawns on Grade: shall consist of 10% compost and 90% topsoil, by volume. These materials must meet specifications described in Paragraph 6. B. Loosen subgrade lawn areas to a minimum of 3”. Remove stones more than 1-1/2” in any dimension and sticks, roots, rubbish, and other extraneous matter. Limit preparation to areas which will be planted promptly after preparation. C. Spread soil mix for lawn areas on grade to a minimum depth of 4” as required to meet grade and elevations shown on drawings, after lightly rolling and natural settlement. Allow for sod thickness in areas to be sodded. 12. INSTALLATION OF SOIL MIX FOR TREE PITS ON GRADE A. Confirm that native subsoil drains at a rate of at least ½” per hour. If drainage is less than ½” per hour, provide subsurface drainage lines. B. Install 30-36” of Soil Mix for Tree Pit Backfill on Grade: 1) Shall consist of clay loam to sandy clay loam soil, sand, and composted pine bark fines at a rate of 5:5:1 to 10:5:1.5 to achieve the following: (a) Clay content of Soil Mix shall be 10-20% of the soil mix, by volume. (b) Minimum amount of coarse to medium sand in the mix shall be 55% (c) Minimum infiltration rate at 80-85% compaction shall be 1-3 inches per hour. C. Composted pine bark fines shall not exceed 10% of the total soil mix by volume. D. Till 4” of compost into the top 6” of the installed Soil Mix for Tree Pit Backfill on Grade. 13. INSTALLATION OF SOIL MIX FOR MULCHED SHRUB AND PERENNIAL BEDS: A. Confirm that native subsoil drains at a rate of at least ½” per hour. If drainage is less than ½” per hour, provide subsurface drainage lines. B. Install 4” of Soil Mix for Mulched Shrub and Perennial Beds on Grade: 1) Shall consist of clay loam to sandy clay loam soil, sand, and composted pine bark fines at a rate of 5:5:1 to 10:5:1.5 to achieve the following: (a) Clay content of Soil Mix shall be 10-20% of the soil mix, by volume. (b) Minimum amount of coarse to medium sand in the mix shall be 55% (c) Minimum infiltration rate at 80-85% compaction shall be 1-3 inches per hour. 2) Composted pine bark fines shall not exceed 10% of the total soil mix by volume. C. Till 4” of compost into the top 6” of the installed Soil Mix for Tree Pit Backfill on Grade. 14. GENERAL PLANT INSTALLATION: A. Excavation: Excavate all tree pits and planting areas to the width and depth shown in the planting details. B. Center plant in pit and orient for the best visual effect. Set plants plumb and hold rigidly in position until soil has been tamped firmly around root ball. C. Mulch within 48 hours after planting and after applying the pre-emergent herbicide, except ground cover areas (which shall have organic material placed before planting) with a 3" layer of mulch immediately after planting. All bed lines shall be cut with a smooth consistent edge to a minimum depth of 3 inches. Keep mulch out of the crowns of shrubs and off buildings, sidewalks, light standards, and other structures. D. All planting areas to conform to specified grades after full settlement has occurred and mulch has been applied. Provide saucers around tree pits as shown on planting details. Remove all tags, labels, strings, etc. from all plants. 15. MAINTENANCE AND GUARANTEE: A. The landscape contractor shall be responsible for maintaining his work until final acceptance by the owner or the owner's representative. Maintenance shall include watering, weeding, cultivating, mulching, removal of dead materials, resetting of plants to proper grades or upright positions, restoration of earth berms, and other necessary operations. adequate protection for lawn areas against trespassing during planting operations and against damage of any kind shall be provided. nothing in these notes is intended to relieve the contractor of his responsibility to repair existing lawn areas damaged by workmen engaged in the completion of this project. B. Inspection of the work to determine completion of the contract exclusive of the possible replacement of plantings during the warranty period, will be made by the owner or the owner's representative at the conclusion of the installation period upon written notice requesting such inspection. Request shall be submitted by contractor at least ten days prior to the anticipated date for inspection. After inspection, the contractor will be notified in writing by the owner or the owner's representative of acceptance of the work or, if there are any deficiencies, the contractor will be notified of the requirements necessary for completion of the work. Plantings shall not be considered accepted until all deficiencies have been corrected and approved in writing. C. Nursery stock shall be fully guaranteed for one full year. All plants that fail to make new growth from a dormant condition or that die during the first year after planting shall be replaced. All replacements shall conform with the original specifications as to size and type. All costs of replacements shall be borne by the contractor. D. The contractor shall be responsible for the removal of all unused materials, rubbish, debris, or plant material not planted from the site upon completion of his work. E. All other items necessary to make work complete shall be finalised prior to final inspection. 16. PERMANENT SEEDING: A. Prior to seeding contractor shall provide and spread 4" of topsoil as specified on all areas to receive permanent seeding. B. Topsoil that has become hard and compacted before permanent seeding has been applied shall be scarified to prepare seed bed for receiving seed. C. The contractor shall seed all denuded areas and areas disturbed by construction that are not otherwise stabilized with paving, buildings, or planted and mulched within the contract limits, unless specifically noted otherwise. D. If a utility line is installed through a landscaped lawn the seeding shall be modified to restore ground cover comparable to the existing lawn I. Seeding includes seedbed preparation, liming, fertilizing, seeding, and mulching of disturbed areas. J. Seed shall be blue tag certified and shall be labeled in accordance with the state laws and the U.S. Department of Agricultur e rules and regulations under the Federal Seed Act in effect on the date of invitations for bids. Bag tag figures are evidence of purity and germination. K. Lawn Seed varieties shall be an improved turf-type variety known to perform well in the project area. Seed mixture shall be chosen to ensure the development of plants during the season of planting, and to ensure future growth and permanent stabilization. Seed shall conform to the requirements of the Virginia Crop Improvement Association (VCIA). L. All seed shall conform to the current rules and regulations of the state where it is being used and shall be from the latest crop available.The seed shall be State-certified to meet Virginia seed certification standards and specifications, absolutely true to varietal type, and free from weeds, fungus, insects and disease of any kind. M.No seed will be accepted with a test date of more than 9 months before the delivery date to the site. N. Seed that has become wet, moldy, or otherwise damaged in transit or storage will not be accepted. The percent of noxious weed seed allowable shall be as defined in the current State laws relating to agricultural seeds. O. LIMING: Lime shall be applied separately and prior to the application of any fertilizer or seed and only on seedbeds, which have previously been prepared. The lime shall be worked into the top 3 inches of soil after which the seedbed shall again be properly graded and dressed to a smooth finish. Lime shall be applied at the rate specified by the soil test report recommendations. P. FERTILIZING: Following advance preparations and cleanup, fertilizer shall be uniformly spread at the rate specified in the soil test report recommendations. Q. SEEDING: Grass seed shall be sown at the rate specified in the permanent seeding schedule and notes immediately after fertilizing and the fertilizer and seed raked into the soil.Seeds shall be inoculated before mixing or sowing in accordance with the instructions of the seed provider and manufacturer of the inoculant. When seeding is required at other than the seasons shown in the permanent seeding schedule, a cover crop shall be sown by the same methods required for grass seeding and permanent seeding shall be sown during the following permanent seeding season. R. Sow seed with spreader or seeding machine. Do not broadcast or drop seed when wind velocity exceeds 5 mph. Evenly distribute seed by sowing equal quantities in two directions at right angles to each other. Do not seed against existing trees. S. Rake seed and fertilizer lightly into top 1/8 inch of soil and water with fine spray. T. MULCHING: Protect seeded areas with slopes not exceeding 3:1 by spreading straw mulch. Spread uniformly at a minimum rate of 2 tons/acre to form a continuous blanket 1-1/2 inches in loose thickness over seeded areas. Spread by hand, blower, or other suitable equipment. Protect slopes 3:1 and greater with erosion control mats and fasten as recommended by material manufacturer. U. Straw mulch material--Straw mulch shall consist of wheat, barley, oat or rye straw. The mulch material shall be air-dry, reasonably light in color, and shall not be musty, moldy, caked, or otherwise of low quality. The use of mulch that contains noxious weeds is not permitted. V. Other mulch materials--Mulching materials, such as wood cellulose fiber mulch, synthetic fiber mulch, netting, and mesh, are other mulching materials that may be required for specialized locations and conditions. These materials must be installed according to the manufacturer's recommendations for methods of application. W.After the seed has been properly covered, the seedbed shall be immediately compacted by means of an approved lawn roller weighing 40 to 65 pounds per foot of width for clay soil (or any soil having a tendency to pack) or weighing 150 to 200 pounds per foot of width for sandy or light soils. 17. LAWN MAINTENANCE: A. Within the contract limits, the contractor shall produce a dense, well established lawn. The contractor shall be responsible for maintaining the lawn until acceptance by the owner or owner's authorized representative. B. Maintenance shall include but may not be limited to watering, weeding, and fertilizing as necessary as well as the repair and re-seeding of all eroded, sunken or bare spots (larger than 12"x12") until certification of acceptability by the owner or owner's representative. Repaired seeding shall be accomplished as in the original work (including re-grading if necessary). 18. ACCEPTANCE: A stand of permanent lawn grass as specified shall be considered acceptable when the turf cover is at least 95%. The Contractor shall overseed, and otherwise maintain the grassed areas until the stand of grass has reached a uniform height of 3 to 4 inches and a state of uniform species maturity. Annual grasses and grain weeds shall not be considered part of the cover percentage, and seeding stands shall not be considered acceptable until the stand reaches a state of uniform post-seeding maturity for the specified species. PERMANENT SEEDING SHALL BE BLUE TAG CERTIFIED AND SELECTED FROM THE CURRENT VIRGINIA TURFGRASS VARIETY RECOMMENDATIONS AS PUBLISHED BY VIRGINIA TECH, VIRGINIA COOPERATIVE EXTENSION. SEED SELECTED SHALL BE OF A VARIETY KNOWN TO PERFORM WELL IN THE PROJECT AREA AND SHALL BE OF A VARIETY THAT IS KNOWN TO BE TOLERANT OF FULL SUN, AND ONCE ESTABLISHED, TOLERANT OF PERIODS OF INFREQUENT RAINFALL. PERMANENT LAWN GRASS SEEDING OUTSIDE OF THE PREFERRED SEEDING DATES WILL NOT BE ACCEPTED UNTIL THE FOLLOWING GROWING SEASON AND ONLY WHEN AN ACCEPTABLE STAND OF PERMANENT GRASS IS ESTABLISHED AND ACCEPTED BY THE OWNER. SPRING AND FALL SEEDING: SEED SHALL CONSIST OF A BLEND OF THREE OF THE FOLLOWING VARIETIES KNOWN TO PERFORM WELL IN THE PROJECT AREA. SELECTED VARIETIES SHALL BE SEEDED AT THE SPECIFIED RATES PER ACRE. FOR ALL AREAS SEEDED WITH PERMANENT LAWN GRASS IN THE SPRING OR FALL (SEE SPECIFIED SEEDING DATES BELOW): TYPE OF GRASS SEEDING RATE SEEDING DATE TALL FESCUE 5 - 7 LBS./1000 SQ. FT. SPRING SEEDING: FEBRUARY 28, TO MAY 15. FALL SEEDING: AUGUST 1 TO NOVEMBER 1 NOTE: PREFERRED FESCUE SEEDING DATES ARE FROM AUGUST 1 TO NOVEMBER 1. 4TH MILLENNIUM SRP, ANNAPOLIS, AVENGER II4, AVENGER III, BIRMINGHAM1, BLACK TAIL, BLOODHOUND4, BULLSEYE1, BULLSEYE LTZ, CATALYST, CROSSFIRE 4, DAYBREAK, DEGAS, DRAGSTER, DYNAMITE G-LS, FANTASIA, FASTLANE, FAYETTE, FIREBIRD 2, FIRECRACKER G-LS, FIRECRACKER SLS, FIREHAWK SLT, FIRENZA II, FIREWALL4, GAZELLE II4, GOLD MEDALLION4, GRANDE 3, GTO, GUARDIAN 41, HEMI, HOUNDOG 84, INFERNO4, INTEGRITY4, JUSTICE4, LIFEGUARD, MAESTRO, MICHELANGELO, MONUMENT, MOONDANCE GLX, MUSTANG 44, PARAMOUNT, PENN RK44, PRO GOLD, RAPTOR III, REBEL IV4, REBEL V4, REBEL XLR4, REBOUNDER4, REFLECTION, REGENERATE, RENDITION RX4, ROCKWELL, ROWDY4, SALTILLO4, SCREAMER LS, SERENADE, SPYDER LS4, SPYDER 2LS, SR 8650, STANDOUT4, STEALTH, SUNSET GOLD4, SUPERSONIC, SYMPHONY, TECHNIQUE, TEMPLE, THOR, TITANIUM 2LS, TITANIUM G-LS, TITAN RX4, TRINITY, TURBO4, TURBO RZ4, VALKYRIE LS, WICHITA, AND XTREMEGREEN4. BATTLE HAWK, BENTLEY, BLADERUNNER 3, BONFIRE, BRAVO 2, CAPITAN, CLASH, ENDGAME, ESSENTIAL 2, ESTRENA, EXTRAVAGANZA, FAIRFIELD, FALCON SUPREME, FINELAWN SUPREME, GALACTIC, GALLARDO, GLX ACED, GLX REVIVE, GRO_PRO, HELLCAT GLR, HOUNDOG 9, KIZZLE, LAFAYETTE, MATISSE, MOTIF, NATURALLY GREEN, OKEEFE, ORIOLE, PADRE 2, PROVIDENCE, RACEWAY, RAPTOR LS, ROVER, ROWDIER, SR 8700, TALLADEGA II, TANK, TEACHER, TITAN GLX, TITAN MAX, TOUGH, TRIAD, VALSETZ, XANADU, AND ZION. SEED WITH THE FOLLOWING MIXTURE(S) FOR SPECIFIED DATES OUTSIDE THOSE LISTED FOR FESCUE OR AS LISTED BELOW: TYPE OF GRASS SEEDING RATE SEEDING DATE BERMUDA 2 LBS./ 1,000 SQ. FT.(HULLED SEED) FEBRUARY - MAY 7 LBS. / 1,000 SQ. FT. (HULLED SEED) AND AUGUST - JANUARY 5 LBS. / 1,000 SQ. FT. WINTER RYE ONLY THE FOLLOWING VARIETIES OF BERMUDA SHALL BE ACCEPTABLE: PRINCESS 77, ARDEN 154, MONACO, RIO, SUNQUEEN, AND SWI-10704. ALL SEED SHALL HAVE A MINIMUM PURITY OF 95% AND AN 85% GERMINATION RATE. 1 234567 A B C D E SHEET NAME: PROJECT NO: DATE ISSUED: SHEET NO: DESIGNED BY: DRAWN BY: CHECKED BY:ISSUANCE SCHEDULE NUMBER DATE DESCRIPTION 4433 CORPORATION LANE SUITE 125 VIRGINIA BEACH, VA 23462 800.414.1045 Autodesk Docs://City of Suffolk VA -Projects HUB_R24/_W_Saratoga East Parking Lot_ARCH_R24.rvt 9/9/2025 7:32:48 AM TRN JSB TRN 1002400.28 03/03/2026 SARATOGA EAST PARKING LOT CITY OF SUFFOLK 153 N. MAIN STREET SUFFOLK, VA 23434 E001 AREA SITE LIGHTING FIXTURE LIGHTING FIXTURE TYPE SYMBOL. SEE LIGHTING FIXTURE DETAILS. ELECTRICAL CIRCUIT RUN IN CONDUIT AND CIRCUIT HOMERUN TO PANELBOARD (PANEL AND CIRCUIT DESIGNATION AS INDICATED). AS A MINIMUM CONDITION, EACH SINGLE PHASE CIRCUIT SHALL HAVE 1 #12 PHASE CONDUCTOR, 1 #12 NEUTRAL CONDUCTOR AND 1 #12 GROUNDING CONDUCTOR IN 1/2" CONDUIT. PROVIDE ADDITIONAL PHASE CONDUCTORS AS REQUIRED FOR "MULTIPLE PHASED" ELECTRICAL LOADS. PROVIDE NEUTRAL CONDUCTOR TO ALL WALL SWITCH OUTLET BOXES WHETHER REQUIRED OR NOT. PROVIDE ADDITIONAL "SWITCH LEG" CONDUCTORS TO PROVIDE THE LIGHT FIXTURE CONTROL INDICATED. MULTIPLE SINGLE PHASE CONDUCTORS MAY BE GROUPED TOGETHER IN A COMMON CONDUIT IN ACCORDANCE WITH THE NEC AND AT THE CONTRACTOR'S DISCRETION. GROUNDING CONDUCTORS MAY BE SHARED AS ALLOWED BY THE NEC. NEUTRAL CONDUCTORS SHALL NOT BE SHARED. MULTI-POLE BREAKERS SHALL BE PROVIDED IN ACCORDANCE WITH THE NEC WHERE MULTI-WIRE BRANCH CIRCUITS ARE REQUIRED. CONDUIT LARGER THAN 1/2" AND CONDUCTORS LARGER THAN #12 SHALL BE AS INDICATED. LIGHTING POWER GENERAL WALL MOUNTED LIGHTING FIXTURE NEW WORK NOTE SYMBOL GENERAL ELECTRICAL NOTES ELECTRICAL LEGEND AND A 1 GENERAL: UNLESS SPECIFICALLY INDICATED OTHERWISE, ALL WORK SHOWN ON ELECTRICAL DRAWINGS IS NEW WORK TO BE PROVIDED UNDER THIS CONTRACT. COORDINATION: COORDINATE AND COOPERATE WITH ALL TRADES ON THE PROJECT. THE CONTRACTOR SHALL REVIEW ALL CONTRACT DOCUMENTS INCLUDING CIVIL, STRUCTURAL, ARCHITECTURAL DRAWINGS AND SPECIFICATIONS. CONTRACTOR SHALL COORDINATE AND ADJUST ACCORDINGLY AS DIRECTED BY THE CONTRACTING OFFICER. AS-BUILT DRAWINGS: SECURE AN EXTRA SET OF ELECTRICAL DRAWINGS TO BE KEPT ON SITE AND MARK, DAILY, THE DRAWINGS IN RED AS THE PROJECT PROGRESSES IN ORDER TO KEEP AN ACCURATE RECORD OF ALL DEVIATIONS BETWEEN THE WORK SHOWN ON THE DRAWINGS AND THE WORK WHICH IS ACTUALLY INSTALLED. THESE MARKED DRAWINGS SHALL REFLECT ANY AND ALL CHANGES AND REVISIONS TO THE ORIGINAL DESIGN WHICH EXISTS IN THE COMPLETED WORK. DELIVER THE MARKED DRAWINGS TO THE OWNER AT PROJECT CLOSE-OUT. TESTS: TEST ALL WIRING FOR CONTINUITY AND GROUNDS BEFORE CONNECTING ANY FIXTURES OR DEVICES. PERFORM INSULATION RESISTANCE TESTS ON ALL WIRING #6 OR LARGER TO ENSURE THAT ALL PORTIONS ARE FREE FROM SHORT-CIRCUITS AND GROUNDS. INSPECTIONS: ARRANGE ALL NECESSARY INSPECTIONS. DELIVER ALL REQUIRED INSPECTION CERTIFICATES TO THE OWNER. GROUNDING: PROVIDE GROUNDING IN ACCORDANCE WITH THE NEC FOR THE ENTIRE ELECTRICAL SYSTEM INCLUDING EQUIPMENT FRAMES CONDUITS, SWITCHES, CONTROLLERS, WIRE-WAYS, NEUTRAL CONDUCTORS, AND OTHER EQUIPMENT. PROVIDE A GROUNDING CONDUCTOR IN ALL POWER CONDUITS. LABELS: PROVIDE LABELS FOR ALL PANELBOARDS. LABELS SHALL BE MACHINE ENGRAVED, LAMINATED PLASTIC, PERMANENTLY ATTACHED WITH SELF-TAPPING SCREWS OR RIVETS. DO NOT USE SELF-ADHESIVE LABELS. LABEL SHALL INDICATE EQUIPMENT DESIGNATION AND ASSOCIATED PANEL AND CIRCUIT THAT SERVES IT. J-BOX LABELING: LABEL ALL JUNCTION BOXES WITH PERMANENT MARKER IDENTIFYING CIRCUIT NUMBER AND PANELBOARD OF CIRCUITS WITHIN. PANEL DIRECTORY: PROVIDE TYPEWRITTEN PANELBOARD DIRECTORY CARD IN EACH PANELBOARD WITH CIRCUIT LOAD INFORMATION AND ROOM NUMBER CLEARLY IDENTIFIED. USE ACTUAL ROOM NUMBERS IN THE BUILDING, NOT THE ROOM NUMBERS SHOWN ON THE CONTRACT DRAWINGS, AS THEY ARE OFTEN DIFFERENT. LIGHTING CONTROL TESTING: UPON COMPLETION OF THE INSTALLATION OF ALL LIGHTING SYSTEMS AND CONTROL DEVICES, CONTRACTOR SHALL RETAIN AN APPROVED AGENCY TO PERFORM FUNCTIONAL TESTING OF THE LIGHTING CONTROL .THE TESTING SHALL CONFIRM THAT ALL CONTROL HARDWARE AND SOFTWARE ARE CALIBRATED, ADJUSTED, PROGRAMMED, AND IN PROPER WORKING CONDITION, IN ACCORDANCE WITH THE CONSTRUCTION DOCUMENTS AND THE MANUFACTURER'S INSTRUCTIONS. THE CONTRACTOR SHALL PROVIDE REPORT OF EVIDENCE OF SUCCESSFUL FUNCTIONAL TESTING TO THE OWNER AND ENGINEER PRIOR TO FINAL INSPECTION. MOUNTING HEIGHTS: MOUNTING HEIGHTS INDICATED ARE FROM THE FINISHED FLOOR TO THE CENTERLINE OF THE WIRING DEVICE UNLESS OTHERWISE NOTED. MOUNTING HEIGHTS OF LIGHTING FIXTURES ARE TO THE BOTTOM OF THE FIXTURE UNLESS OTHERWISE NOTED. BARRIERS: WHERE A MULTIPLE-GANG BOX HAS CIRCUITS OF DIFFERENT VOLTAGES OR SYSTEMS WHICH ARE REQUIRED TO BE SEPARATED, PROVIDE THE CODE-REQUIRED SEPARATION USING A FULL HEIGHT AND DEPTH BARRIER PLATE. CLEAN UP: ON PROJECT CLOSE-OUT CLEAN ALL ELECTRICAL DEVICES, LIGHTING FIXTURES, LENSES, AND REMOVE ALL PAINT SPATTERS FROM DEVICES, FIXTURES AND PLATES. REPAIR ALL INOPERATIVE LIGHTING FIXTURES. ABBREVIATIONS A AMPERE AFG ABOVE FINISHED GRADE AWG AMERICAN WIRE GAUGE BFG BELOW FINISHED GRADE C CONDUIT CKT CIRCUIT GFI GROUND FAULT INTERRUPTER GND GROUND KAIC THOUSAND AMPERE INTERRUPTING CAPACITY KVA KILO-VOLT-AMPERES KW KILO-WATTS LPW LUMENS PER WATT LTG LIGHTING MCA MINIMUM CIRCUIT AMPS MCB MAIN CIRCUIT BREAKER MFDM MULTI-FUNCTION DIGITAL METER MFR MANUFACTURER MIN MINIMUM MLO MAIN LUGS ONLY NEC NATIONAL ELECTRICAL CODE P POLE PL PROPERTY LINE PNL PANEL Ø PHASE PVC POLYVINYL CHLORIDE SCH SCHEDULE SE SERVICE ENTRANCE TYP TYPICAL UFC UNIFIED FACILITIES CRITERIA UGC UNDERGROUND CONDUIT UON UNLESS OTHERWISE NOTED V VOLT W WATTS/WIRE WP WEATHERPROOF TELECOMMUNICATIONS UNDERGROUND CONDUIT FOR LOW VOLTAGE CABLING, PROVIDE (1) 1" HDPE C. WITH PULL STRING, BURIED MIN. 24" WITH MARKER TAPE MIN. 12" BFG IP SURVEILLANCE CAMERA SYSTEM (PATHWAY INFRASTRUCTURE ONLY) POLE MOUNTED SURVEILLANCE CAMERA UGC HH HANDHOLE, PROVIDE 12" X 24" X 24"D SIZED HANDHOLE. SEE DETAIL SHEET E-501 FOR ADDITIONAL INFORMATION. PHOTOMETRIC CALCULATION POINT - SUPERSCRIPT INDICATES LIGHTING LEVEL IN FOOT-CANDLES 1.0 ELECTRICAL PANELBOARD DEVICES AND CABLING PROVIDED BY SECURITY VENDOR A5 A4 A4 B B ALLEYWAY PROPERTY LINE PARKING AREA A5 0.7 2.0 1.0 2.7 4.4 4.2 0.3 1.4 3.4 5.6 0.4 2.1 4.0 4.3 0.6 2.7 4.3 3.2 1.2 3.5 3.9 2.6 0.4 1.7 3.7 4.3 2.1 5.0 6.3 3.6 3.4 2.4 1.6 0.3 1.4 2.1 2.4 0.9 1.4 2.1 3.1 4.9 0.9 1.2 1.6 2.4 3.6 5.3 4.6 4.9 2.1 1.1 1.4 1.7 2.3 3.3 4.7 5.4 5.9 4.8 3.3 1.8 0.9 1.0 1.4 1.7 1.8 2.0 2.4 3.1 4.0 4.5 3.8 3.1 2.3 2.0 2.3 2.5 1.2 1.6 2.2 2.4 2.4 2.3 2.7 3.1 3.0 2.7 2.5 2.7 3.2 4.8 4.9 2.6 0.9 1.3 2.0 3.1 3.7 3.5 2.6 2.3 2.3 2.4 2.3 2.3 2.7 3.5 5.1 5.7 3.0 0.7 1.0 1.5 2.5 4.1 5.7 4.6 3.3 2.5 2.1 2.0 2.0 2.1 2.4 3.2 4.4 5.3 5.8 4.8 3.3 1.8 1.7 2.9 5.0 6.8 5.6 3.6 2.4 1.9 1.9 1.9 1.9 2.0 2.4 2.9 3.6 4.3 3.8 2.9 2.0 0.6 0.9 1.2 1.9 3.2 5.1 6.5 6.6 4.9 3.0 2.1 1.7 1.7 1.8 1.9 2.0 2.1 2.2 2.5 2.8 2.8 2.3 1.7 1.1 0.7 0.7 0.9 1.2 1.7 2.6 3.7 4.6 5.1 3.9 2.5 1.8 1.5 1.6 1.7 2.0 2.4 2.8 2.8 2.4 2.3 1.9 1.5 1.0 0.4 0.6 0.9 1.1 1.3 1.7 2.3 2.8 3.1 2.7 2.0 1.5 1.4 1.5 1.6 2.2 3.2 4.2 3.3 3.1 2.3 1.7 1.3 0.9 0.3 0.5 0.7 0.8 0.9 1.1 1.5 2.0 2.1 1.9 1.5 1.4 1.3 1.4 1.6 2.4 3.9 5.9 3.9 2.5 1.6 1.1 0.7 0.4 0.5 0.6 0.8 1.2 1.9 1.9 1.6 1.3 1.3 1.4 1.7 2.6 4.3 6.5 6.0 3.8 2.3 1.4 1.0 0.6 1.3 2.6 2.5 1.1 1.3 1.7 2.6 4.2 5.8 6.3 5.4 3.3 2.0 1.3 0.9 3.2 2.7 0.6 0.8 1.0 2.1 2.9 3.6 4.1 3.8 2.7 1.7 1.1 0.8 1.0 1.1 1.2 2.1 2.3 2.3 1.9 1.4 0.9 1.1 1.2 1.4 1.4 1.4 1.1 0.9 0.9 1.0 0.9 0.6 0.7 0.7 0.4 0.4 0.10.10.10.10.10.10.10.10.10.1 0.1 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.1 0.1 0.0 0.1 0.1 0.1 0.1 0.2 0.2 0.4 0.3 0.4 0.4 0.3 0.2 0.2 0.1 0.1 0.2 0.2 0.2 0.3 0.3 0.5 0.5 0.3 0.2 0.2 0.2 0.2 0.4 0.6 0.6 0.7 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.5 0.4 0.3 0.4 0.4 1234 567 A B C D E SHEET NAME: PROJECT NO: DATE ISSUED: SHEET NO: DESIGNED BY: DRAWN BY: CHECKED BY:ISSUANCE SCHEDULE NUMBER DATE DESCRIPTION 4433 CORPORATION LANE SUITE 125 VIRGINIA BEACH, VA 23462 800.414.1045 Autodesk Docs://City of Suffolk VA -Projects HUB_R24/_W_Saratoga East Parking Lot_ARCH_R24.rvt 9/9/2025 7:32:48 AM TRN JSB TRN 1002400.28 03/03/2026 SARATOGA EAST PARKING LOT CITY OF SUFFOLK 153 N. MAIN STREET SUFFOLK, VA 23434 GRAPHIC SCALE: E002 SITE PHOTOMETRIC PLAN SCALE: 1" = 20'-0" 1" = 20'-0" 20' 10' 0' 40' 20' 60' N Statistics Description Symbol Avg Max Min Max/Min Avg/Min Parking Area 2.4 fc 6.8 fc 0.3 fc Alleyway 2.8 fc 6.3 fc 0.3 fc Property Line 0.3 fc 0.7 fc 0.0 fc 21.0:1 9.3:1 22.7:1 8.0:1 N/A N/A A5 A4 A4 B B A5 1 1 3 2 HH UGC UGC UGC UGC UGC UGC UGC UGC 5 4 6 1234 567 A B C D E SHEET NAME: PROJECT NO: DATE ISSUED: SHEET NO: DESIGNED BY: DRAWN BY: CHECKED BY:ISSUANCE SCHEDULE NUMBER DATE DESCRIPTION 4433 CORPORATION LANE SUITE 125 VIRGINIA BEACH, VA 23462 800.414.1045 Autodesk Docs://City of Suffolk VA -Projects HUB_R24/_W_Saratoga East Parking Lot_ARCH_R24.rvt 9/9/2025 7:32:48 AM TRN JSB TRN 1002400.28 03/03/2026 SARATOGA EAST PARKING LOT CITY OF SUFFOLK 153 N. MAIN STREET SUFFOLK, VA 23434 GRAPHIC SCALE: E003 1" = 20'-0" 20' 10' 0' 40' 20' 60' 1 2 3 4 5 6 7 ROUTE CIRCUIT THROUGH LIGHTING CONTROL PANEL "LCP" IN GODWIN - VIRGINIA PILOT BUILDING. CONNECT SITE LIGHTING CIRCUIT TO SPARE CIRCUIT MADE AVAILABLE IN GODWIN - VIRGINIA PILOT BUILDING, PANEL MDP1-6. CONNECT EXTERIOR LIGHTING CIRCUIT TO SPARE CIRCUIT MADE AVAILABLE IN GODWIN - VIRGINIA PILOT BUILDING, PANEL MDP1-8. 2 #12, 1 #12 GND - 1"C ENTIRE LENGTH OF RUN. 2 #10, 1 #10 GND - 1"C ENTIRE LENGTH OF RUN. APPROXIMATE LOCATION OF PANEL MDP1. UNDERGROUND CONDUIT ROUTING IS DIAGRAMMATIC ONLY. CONTRACTOR SHALL COORDINATE EXACT ROUTING IN FIELD. NOTES THIS SHEET ELECTRICAL SITE PLAN SCALE: 1" = 20'-0" N 1234 567 A B C D E SHEET NAME: PROJECT NO: DATE ISSUED: SHEET NO: DESIGNED BY: DRAWN BY: CHECKED BY:ISSUANCE SCHEDULE NUMBER DATE DESCRIPTION 4433 CORPORATION LANE SUITE 125 VIRGINIA BEACH, VA 23462 800.414.1045 Autodesk Docs://City of Suffolk VA -Projects HUB_R24/_W_Saratoga East Parking Lot_ARCH_R24.rvt 9/9/2025 7:32:48 AM TRN JSB TRN 1002400.28 03/03/2026 SARATOGA EAST PARKING LOT CITY OF SUFFOLK 153 N. MAIN STREET SUFFOLK, VA 23434 E501 CONCRETE BASE DETAIL Ø 16" 42" 4" 24" 12" 1 #6 BARE 10'-0" LONG x 3/4" DIA. COPPER CLAD GROUND ROD 1" CHAMFER PROVIDE NON-SHRINK GROUT, PACKED UNDER POLE BASE TO INSURE FULL CONTACT WITH FOOTING AND PREVENT LOOSENING OF LEVELING NUTS. PROVIDE WEEP HOLES FOR DRAINAGE. CAST ALUMINUM BASE COVER LEVELING NUT AND WASHER POLE SHALL HAVE AN EPA RATING GREATER THAN OR EQUAL TO THE SUM OF ALL FIXTURES MOUNTED TO IT, AT AN ULTIMATE WIND RATING OF 110mph. #3 (ASTM A615 GRADE 60) HORIZONTAL REINFORCING BARS AT 12" OC #4 (ASTM A615 GRADE 60) VERTICAL REINFORCING BARS AT 6" OC HOT DIPPED GALVANIZED ANCHOR BOLTS, SIZE PER POLE MANUFACTURER REQUIREMENTS COARSE GRAVEL SETTING BED CONCRETE, 28-DAY COMPRESSIVE STRENGTH NOT LESS THAN 4000 PSI CIRCUIT CONDUCTORS & CONDUIT TO POWER SOURCE OR NEXT POLE. SEE PLAN SHEETS FOR SIZE AND NUMBER OF CONDUITS INTO FOUNDATION LIGHTING FIXTURE, (TYP) REINFORCED HANDHOLE WITH COVER AND STAINLESS STEEL SCREWS, 48"AFG. TERMINATE CONDUIT INTERNALLY, ADJACENT TO HANDHOLE STRAIGHT SQUARE POLE TO MATCH LUMINAIRE FINISH DETAIL BASED ON LSI LIGHTING, "SLM" SERIES LED AREA LIGHTING FIXTURE 20'-0" AFG ON POLE2771354000K LED TYPE IV TYPE LUMENS LAMP TYPE VOLTAGE MOUNTING 18,908 INPUT WATTS 20'-0" AFG ON POLE2771614000K LED TYPE V24,953 A4 A5 LUMINAIRE REQUIREMENTS 1. HOUSING SHALL BE DIE-CAST ALUMINUM. LED DRIVER COMPARTMENT SHALL BE SEALED FOR WEATHER-TIGHT OPERATION. 2. LIGHTING OUTPUT PROVIDED BY LED LIGHT BARS, MINIMUM 70 CRI. PROVIDE WITH INTEGRAL SURGE SUPPRESSOR. 3. FINISH COLOR SHALL BE DETERMINED BY OWNER. 4. LABELS: FIXTURE SHALL BE UL LISTED FOR WET LOCATIONS AND ENCLOSURE CLASSIFIED IP66 PER IEC 529. AND TESTED IN ACCORDANCE WITH IESNA LM-79 AND LM-80 STANDARDS AND SURGE PROTECTION TESTED IN ACCORDANCE WITH IEE C62.41.2 AND ANSI 62.41.2 5. PROVIDE FIXTURE WITH INTEGRAL PHOTOCELL. DETAIL BASED ON CURRENT LIGHTING, "TRP2" SERIES LED WALLPACK SURFACE, WALL, 12'-0" AFG27745.14000K LED TYPE LUMENS LAMP TYPE VOLTAGE MOUNTING 5,749 INPUT WATTS LUMINAIRE DESCRIPTION: 1. FIXTURE SHALL BE DIE CAST ALUMINUM HOUSING. 2. FINISH SHALL BE SELECTED BY OWNER. 3. FIXTURE SHALL HAVE TYPE IV DISTRIBUTION. 4. FIXTURE SHALL BE UL LISTED FOR WET LOCATIONS. 16" 9" B 6. PROVIDE INTEGRAL LOUVER WHERE INDICATED A4 PROVIDE PRE-DRILLED HOLES FOR SECURITY VENDOR PROVIDED CAMERAS. COORDINATE WITH SECURITY VENDOR FOR DIMENSIONS AND REQUIREMENTS PROVIDE 12"x12" NEMA-3R RATED ENCLOSURE WITH REMOVABLE MOUNTING PLATE AND DIN RAIL MOUNTING. (EQUIPMENT PROVIDED BY SECURITY VENDOR IN THIS CONTRACT) STAINLESS STELL METAL STRAP FOR MOUNTING. (TYP) 1" EC PATHWAY FROM HAND HOLE 1234 567 A B C D E SHEET NAME: PROJECT NO: DATE ISSUED: SHEET NO: DESIGNED BY: DRAWN BY: CHECKED BY:ISSUANCE SCHEDULE NUMBER DATE DESCRIPTION 4433 CORPORATION LANE SUITE 125 VIRGINIA BEACH, VA 23462 800.414.1045 Autodesk Docs://City of Suffolk VA -Projects HUB_R24/_W_Saratoga East Parking Lot_ARCH_R24.rvt 9/9/2025 7:32:48 AM TRN JSB TRN 1002400.28 03/03/2026 SARATOGA EAST PARKING LOT CITY OF SUFFOLK 153 N. MAIN STREET SUFFOLK, VA 23434 E701 ELECTRICAL SPECIFICATIONS SECTION 260500 - GENERAL PROVISIONS PART 1 - GENERAL 1.1 Codes and standards - the latest effective publications of all applicable standards, codes, etc., as they apply, form part of these specifications as if were written fully herein and constitute minimum requirements. The following will be referred to throughout in abbreviated forms. A. National Electrical Code, (NFPA 70) (NEC). B. Institute of Electrical and Electronic Engineers (IEEE). C. Rules and regulations of local electric utility company. D. National Electrical Manufacturer's Association (NEMA). E. American National Standards Institute (ANSI). F. Applicable local codes. G. Underwriter's Laboratories, Inc. (UL). H. National Fire Protection Association (NFPA). I. Virginia Uniform Statewide Building Code 1.2 Scope of work - provide all work required for this division including all labor, materials, equipment, appurtenances and services to provide complete electrical systems as shown on the drawings and specified in this division of the specifications. The word "provide" shall mean "furnish and install complete and ready for use". 1.3 The Contractor shall visit the site prior to bid to determine the extent of the work. Lack of knowledge of existing conditions will not be considered a basis for change orders. Prior to ordering equipment, verify that equipment to be provided under this contract is acceptable and can fit into bldg. and room. Expense incurred by the Contractor, which in the Engineer's opinion could have been avoided by this step, shall not be a basis for change orders. 1.4 Drawings and specifications - the drawings are diagrammatic and indicate the general extent, character and arrangement of equipment, fixtures and conduit and wiring systems. It is the intention of these specifications and drawings to fully cover all work and materials for a complete, first-class electrical installation, and any devices such as pull boxes and disconnect switches, usually employed in this class of work, though not specifically mentioned or shown on the drawings or in this specification, but which may be necessary for the satisfactory completion of the work, shall be furnished and installed by the Contractor as a part of his total work under this Division. Consult the specifications and drawings of all other trades and perform all electrical work required therein. Cooperate with all other Contractors or Subcontractors to furnish complete workable systems. 1.5 During construction, keep an accurate record of all deviations between the work as shown on the contract drawings and that which is actually installed on a set of blue line prints of the electrical drawings, and note changes thereon with red marks, in a neat and accurate manner. When all revisions have been shown on these prints to indicate the work as finally installed, the prints shall be delivered to the Owner, before final payment. 1.6 Permits, inspection and tests - the right is reserved to inspect and test any portion of the installation/equipment during the progress of its installation. This Contractor shall test all wiring for continuity and grounds before connecting any fixtures or devices. This Contractor shall test the entire system when the work is finally completed to ensure that all portions are free from short circuits and grounds. 1.7 Secure and pay for all required permits and inspections. Inspection certificates from local authorities having jurisdiction shall be delivered to the Owner before final payment. 1.8 Submittals - submit shop drawings, product data and samples within thirty (30) days of award of contract and in accordance with the general conditions and supplementary conditions. Submittals are required for all items provided under this specification. Review of submittals by the Engineer and any associated action taken by the Engineer does not relieve the Contractor of any requirements set forth by the contract documents. PART 2 - PRODUCTS 2.1 Manufacturing standards - materials shall be new and approved and labeled by UL wherever standards have been established by that agency. Defective equipment or equipment damaged in the course of installation or test shall be replaced or repaired in a manner meeting the approval of the Owner. All items of the same type and rating shall be identical. 2.2 Trade names - unless specifically identified otherwise, manufacturers' names and catalog numbers indicated herein and on the drawings are not intended to be proprietary designations. They are to indicate general type and quality of materials and equipment required. Equipment and materials by other manufacturers which in the opinion of the Engineer are of equal quality and which will produce the same results will be considered acceptable. 2.3 Obtain approved shop drawings showing wiring diagrams, connection diagrams, roughing-in and hookup details, from other involved Contractors for all equipment and comply therewith. 2.4 Reasonable amounts of electricity will be made available to the Contractor for the project. The Contractor shall be responsible for extending electricity to the specific required locations within the project. 2.5 Grounding - the entire electrical system, including equipment frames, conduit, switches, controllers, wireways, neutral conductors, and all other such equipment shall be permanently and effectively grounded in accordance with the NEC. Ground rods shall be copper clad steel, 3/4" diameter by 10'-0" long. Provide a separate ground conductor in all branch circuit conduits sized in accordance with the NEC. 2.6 Schedule of work - the schedule of the electrical work shall be arranged to suit the progress of work by the other trades and shall in no way retard progress of construction of the project. 2.7 Work under this division shall proceed in advance of the work of others whenever possible, eliminating all cutting and patching. When such procedure is impossible, cutting and patching shall be done in an approved manner. Cutting shall not endanger structural integrity in any way. Patching shall exactly match contiguous work. Actual work of cutting and patching of existing surfaces shall be performed by the Subcontractor who originally prepared these surfaces, e.g., cutting and patching of masonry wall will be performed by the masonry Subcontractor. Costs of such cutting and patching shall be borne by the electrical Subcontractor. Cutting shall be carefully done and damage to building, piping, wiring or equipment as a result of cutting shall be repaired by skilled mechanics of trade involved. 2.8 Storage and materials - space will be assigned to the Contractor by the Owner for the storage of materials. This Contractor will be responsible for the protection and safekeeping of materials, tools, and equipment. All materials and equipment shall be kept in its assigned place until the time of its installation. Excess materials, dirt and refuse shall be promptly removed from the work site. 2.9 Labeling of equipment A. All panelboards shall be identified by machine engraved laminated plastic designation plates permanently attached thereto with self-tapping screws or rivets. All component parts of each item of equipment or device shall bear the manufacturer's nameplate, giving name of manufacturer, description, size, type, serial and model number and electrical characteristics in order to facilitate maintenance or replacement. B. All panelboards shall be field marked to warn personnel of the potential for Arc Flash. Labels shall state "WARNING - ARC FLASH AND SHOCK HAZARD APPROPRIATE PPE REQUIRED". 2.10 Coordination - cooperate and coordinate efforts with all Contractors on the project. This verification must be executed regardless of information placed on the drawings. Any cost incurred which in the opinion of the Owner, could have been avoided by this step shall be the responsibility of the electrical Contractor. 2.11 Guarantee of work - Contractor guarantees by his acceptance of the contract that all work installed is free from any and all defects in workmanship and/or materials, and that the apparatus will develop capacities and characteristics specified, and that if, during the period of one year or as otherwise specified, from date of certificate of completion and acceptance of the work any such defects in workmanship, material or performance appear, he will, without cost to the Owner, remedy such defects within a reasonable time to be specified in notice. In default thereof, the Owner may have such work done and charge cost to Contractor. Equipment guarantees from date of "start-up" will not be recognized. PART 3 - EXECUTION 3.1 The installation shall be complete including but not limited to the requirements indicated on the drawings and in these specifications. 3.2 Contractor shall thoroughly coordinate and comply with the manufacturer's requirements. Coordination shall be accomplished prior to commencing work. 3.3 All work shall be accomplished in a neat and workmanlike manner consistent with commercial construction practices, code requirements and the local authority having jurisdiction. SECTION 260519 - CONDUCTORS A. Conductors and insulation - wire and cable shall be soft drawn, annealed copper with 600 volt color coded insulation. Minimum wire size shall be #12 awg. Insulation for branch circuits and feeders shall be type THHN-2-THWN-2 or XHHW-2. Conductors No. 8 AWG and larger diameter shall be stranded. Conductors No. 10 AWG and smaller diameter shall be solid, except that conductors for remote-control and signal circuits, classes 1, 2, and 3, may be stranded. B. Provide a separate ground conductor in all raceways sized in accordance with the NEC. C. Joints and terminations - for conductors #12 and #10 all fixture and branch circuits joints in junction and outlet boxes shall be made with UL listed pressure type connectors rated at 600 volts and 105 degrees C. Connectors shall be Ideal Industries "Wing-Nut" or Buchannan "B-Cap", 3M "Scotch-Lok" connectors or equal. Wire #8 and larger shall be joined or terminated with solderless pressure connectors properly taped in layers to form a moisture-tight joint. D. All wiring shall be in conduit unless otherwise noted. SECTION 260533 - RACEWAY, FITTINGS AND BOXES A. Raceways - conduit shall be hot-dipped, zinc coated or sherardized rigid steel (RS), intermediate metal conduit (IMC), electrical metallic tubing (EMT), or Schedule 40 PolyVinyl Chloride (PVC). B. Flexible conduit shall be galvanized, continuous spiral, single strip type. Flexible conduit shall be covered with PVC jacket in wet or damp locations. Provide suitable fittings with ground connector. C. Fittings - all conduit entering or leaving outlet, junction or pull boxes, and cabinets and all conduit stubs shall have bushings. Provide insulating bushings where required by NEC. Provide expansion fittings with bonding jumper where conduits cross expansion joints. 1. Fittings for RS and IMC shall be threaded type. D. Fittings for PVC shall be PVC, primed and glued. E. Non metallic outlet boxes may be provided in PVC raceway systems. Outlet boxes in wet or damp locations shall be cast-metal, threaded hub-type with gaskets. F. Raceway and fitting installation - run conduits concealed within finished walls, ceilings and floors. Conduit 1" and smaller may be run in the floor slab where practicable. G. Conduit run outside of building shall be buried a minimum of 24" below finished grade. H. Do not install PVC in or through fire rated assemblies, in or through any walls, in or through any ceilings, in hazardous areas, in areas subject to severe physical damage, or exposed anywhere in the project. I. Conduit run underground, under slab, or within concrete encasement may be polyvinyl chloride (PVC) or RS or IMC conduit protected with 2 coats of bitumastic paint. Convert PVC to RS or IMC before rising through floor slab or rising out of soil. Conduit run beneath slab shall be properly suspended from slab such that sub-slab settlement will not adversely affect electrical system. SECTION 265100 - LIGHTING FIXTURES A. Fixtures - fixtures shall be as indicated in schedule. B. LED DRIVERS 1. LED Electronic Drivers shall be UL approved and shall have the following characteristics: a. Electronic with Input Voltage range as shown on the drawings ±10%, 50/60 Hz, with primary fusing. b. Output Drive Current shall be 350mA maximum, +/- 5%. c. Power Factor shall be >90% at full load with THD <20% at full load d. Load regulation shall be +/- 1% from no load to full load e. Output shall be isolated f. Case temperature shall be rated for -40°C through +80°C and provided with thermal protection and self-limited short circuit and overload protection. g. Driver Life Rating shall have less than 0.5% failure rate at the LED module's maximum L70 rated life. h. Dimming Range: 100 to 10 percent, unless otherwise noted, of rated lamp lumens. 2. Driver Manufacturer Drivers shall be considered acceptable for approval as manufactured by the following LED Driver manufacturers. a. Advance Transformer Co. b. Magtech c. Thomas Research Products (TRP) d. Osram/Sylvania C. LED FIXTURES 1. Life Rating (L 70) - Provide L70 documentation, defined as time of operation (in hours) to 30% lumen depreciation (70% lumen maintenance), derived from temperature measurement testing under UL1598 environments and directly correlated to LED package manufacturers IESNA LM-80-08 data. 2. Mechanical - Housing shall be designed specifically for use with LED components and incorporate high performance Thermal Management methods, i.e. heat sink(s). No active thermal management/cooling features (i.e. fans), etc. will be allowed. Luminaire configuration shall allow for modular replacement and/or field repair of all electrical components (i.e. LED modules, Drivers, etc.). 3. LED Module Manufacturers LED modules considered acceptable for approval are as manufactured by the following LED component (chip) manufacturers. a. Nichia Corporation. b. Cree, Inc c. Philips LumiLED d. Osram Opto Semiconductors D. No fixtures shall be hung with zip-clips. CITY OF SUFFOLK 442 W. WASHINGTON ST., P.O. BOX 1858, SUFFOLK, VIRGINIA 23439-1858 PHONE: (757) 514-4060 FAX: (757) 514-4099 DEPARTMENT OF PLANNING & COMMUNITY DEVELOPMENT Division of Planning To: Historic Landmarks Commission From: Goncalo Borges, Senior Planner Date: August 13, 2026 Subject: Request for Certificate of Appropriateness HLC202 6-00012, submitted by G. Wayne Rhoads , applicant and agent, on behalf of the City of Suffolk, property owner, to pave the existing gravel parking lot and perform landscaping and pedestrian improvements to support the historic Phoenix Bank of Nansemond at 347 E. Washington Street. The property is further identified as Zoning Map Number 34G25(A)*5, Suffolk Voting Borough, zoned FRRD, Fairgrounds Revitalization and Redevelopment District, and HC, Historic Conservation Overlay District. STAFF REPORT Overview and Proposed Actions The subject property is located at 347 E. Washington Street. This property is part of the East Washington Street District (2002) of the Suffolk Historic Conservation Overlay District and is located in the FRRD, Fairgrounds Revitalization and Redevelopment zoning district. This property is currently vacant, it is not improved and therefore covered in gravel, and it is utilized as (informal) parking for the Phoenix Bank of Nansemond and other buildings/uses in the vicinity. This property is adjacent and complementary to the Phoenix Bank of Nansemond building . The proposed paving, parking, and pedestrian amenities will offer support to the activities that will take place at this City facility. The Phoenix Bank of Nansemond building is one of twenty -one in the district classified as commercial in style, reflecting their use, materials, and form rather than any given architectural style. The building was built in 1921 and is a contributing structure within the district. The building is also individually listed on the National and State registers. The district nomination form describes the building as a representative example of the rise of African American commerce in southeastern Virginia, and as the only African American bank in Suffolk at the time of its construction. HLC2026-00012 August 13, 2026 Page 2 The Fall 1990 issue of Notes on Virginia (Virginia Department of Historic Resources) notes that the Phoenix Bank “stands as an important reminder of an age when it was necessary for blacks to establish their own financial institutions to serve the black business community”. The applicant is proposing the following actions: • Paving the existing gravel surface with standard-duty asphalt. • Mark a total of 8 parking spaces (including 1 ADA accessible parking space). • Install 6” concrete curb per Virginia Department of Transportation (VDOT) standards. • Install gutter per HRPD standards. • ADA accessible ramps with detectable warning surface per VDOT standards. • Install a concrete sidewalk to create a pedestrian area. • Install 2 Dominion Energy 150W EQ. LED 40K Type 3 Cutoff Colonial Mounted at 14 FT. • Install 8 tree wells in the pedestrian area/sidewalk. • Install sod/turf between the pedestrian area/sidewalk and the parking area. • Plant 9 Bosque Elms, 2 Sawtooth Oaks, and 21 shrubs (Dwarf Burford Holly). Please note that, per the Historic Landmark Commission Guidelines (HLC Guidelines), the non - illuminated interpretative sign listed in the application and shown on the site plan has been administratively approved on July 14th, 2026, under case HLC2026-00013. Case History On October 20 th, 2010, a site plan for an improved parking lot (SP2010 -00016), designed to support a potential Suffolk African American History Museum, was approved by the Department of Planning and Community Development. The proposed improvements were never carried out. On May 9th, 2024, the adjacent property where the historic Phoenix Bank of Nansemond is located received approval from the Historic Landmarks Commission (HLC) (request for Certificate of Appropriateness, HLC2024-00009) with conditions to execute the following works: • On the north elevation/front entrance, clean and repair masonry, repair brass letter signage, repair date stone, replace cast stone lintels over second-story windows, replace non-original windows with windows based on original configuration, and replace non -original storefront entrance to match original configuration as specified in the aforementioned COA application. • On the east elevation, repair and re-finish exposed steel, paint CMU, restore masonry, and protect window opening as specified in the aforementioned COA application. • On the south elevation/rear, clean, repair, and repoint brick masonry, install new doors, protect window openings, repair wood fascia, and provide gutter and downspouts as specified in the aforementioned COA application. • On the west elevation, repair and repoint masonry and protect window openings as specified in the aforementioned COA application. HLC2026-00012 August 13, 2026 Page 3 On November 13th, 2025, the adjacent property where the historic Phoenix Bank of Nansemond is located received approval from the HLC (request for Certificate of Appropriateness, HLC2025 - 00017) with conditions to execute the following works: • North Elevation/Front Entrance: install a cornice made of in -kind material to the original – based on the 1988 photographic evidence, and in compliance with the submitted plans prepared by Hanbury, named “Cornice Details” and “Cornice – Elevations”, both d ated September 8, 2025. • The cornice shall be painted in the PPG1002 -7 – Phantom Mist - PPG Paints’ Regional Color Collection: New England. The cornice shall be installed in the north façade using the masonry pockets originally designed with the building (see attached “Proposed Sc ope of Work – REVISED 09-24-2025” and “Historic Photographs, 09/24/2025, Phoenix Bank COA Application” “Cornice – Elevations”, “Cornice – Details”). Public Notice This request has been duly advertised in accordance with the public notice requirements in Section 15.2-2204 of the Code of Virginia, as amended, and with the applicable provisions of the Unified Development Ordinance. A notice, containing a copy of the staff report, was also provided to the applicant on August 7, 2026. Applicable Regulations A. Unified Development Ordinance (UDO) • Section 31-413(f)(1)D, Issuance of Certificates: The Historic Landmarks Commission shall not issue a Certificate of Appropriateness authorizing issuance of any permit if it finds that the action proposed would adversely affect the primary character of the district or the setting of structures and premises of substantial public interest. • Section 31 -413(g)(2), General Considerations : The compatibility with the design, development standards and criteria as included in the City’s adopted Historic District Design Guidelines. B. Suffolk Historic District Design Guidelines (8-16-2023 Version) • Chapter 4, New Construction (pages 70 – 75). • Chapter 5, Site & Setting (pages 77 - 92). C. The Secretary of the Interior’s Standards for Rehabilitation • A property shall be used for its historic purpose or be placed in a new use that requires HLC2026-00012 August 13, 2026 Page 4 minimal change to the defining characteristics of the building and its site and environment. • New additions, exterior alterations, or related new construction shall not destroy historic materials that characterize the property. The new work shall be differentiated from the old and shall be compatible with the massing, size, scale, and architectural features to protect the historic integrity of the property and its environment. • Designing new onsite parking, loading docks, or ramps when required by the new use so that they are as unobtrusive as possible and assure the preservation of the historic relationship between the building or buildings and the landscape. • Complying with barrier -free access requirements, in such a manner that character - defining spaces, features, and finishes are preserved. • Not recommended: Removing or radically changing buildings and their features or site features which are important in defining the overall historic character of the property so that, as a result, the character is diminished. • Not recommended: Introducing a new landscape feature, including plant material, that is visually incompatible with the site, or that alters or destroys the historic site patterns or vistas. • Not recommended: Placing parking facilities directly adjacent to historic buildings where automobiles may cause damage to the buildings or to important landscape features. Staff Analysis 1347 E. Washington Street (Zoning Map Number 34G25(A)*5) is currently vacant; its surface is covered by gravel, and it does not have any historic structures (contributing or non-contributing) or other historic features on it. Upon reviewing the application materials and proposed scope of work, staff finds that the proposed parking, pedestrian, and landscaping improvements to support the adjacent historic Phoenix Bank of Nansemond building are in substantial alignment with the UDO, and with the Suffolk Historic District Design Guidelines (8-16-2023 Version). Parking lot improvements: The applicant is proposing to develop a parking lot with eight spaces in the subject property. This work includes the following actions: paving the existing gravel surface with standard-duty asphalt, creating a total of 8 parking spaces (including 1 ADA accessible parking space) , installing a 6” concrete curb per VDOT standards , and i nstalling a gutter per HRPD standards. These improvements have been designed to not interfere, obstruct, or be adverse to the adjacent historic structure, and to the district in general. Per Section 31 -413(f)(1)D, the proposed parking lot improvements do not adversely affect the primary character of the district or the setting of structures and premises of substantial public interest. Per Section 31 -413(g)(2), all the materials such as asphalt and concrete are considered appropriate to this historic setting. These materials are already present in the Historic District, and the proposed features, such as the asphalt parking HLC2026-00012 August 13, 2026 Page 5 surface, curb, and gutter, are compatible with the design, development standards, and criteria as included in the City’s adopted Historic District Design Guidelines. Considering Chapter 4 of the Historic District Design Guidelines, which guides new construction, and the Secretary of the Interior’s Standards for Rehabilitation, the proposed parking lot improvements are designed to maintain the historic character of the subject property by keeping the design and choice of materials simple and without conflicting or risking damaging the Phoenix Bank of Nansemond structure. The proposed features also match with other parking lots developed and maintained by the City of Suffolk within the historic district. These features are consistent with the setbacks and scale of other existing structures in the historic district. Hence, the proposed improvements are deemed consistent and compatible with the site’s character and its neighboring structures. In what concerns Chapter 5 (Site & Setting guidelines) and other recommendations by the Secretary of the Interior, the proposed parking lot and its features provide an adequate transition of public and private spaces between the public right of way and the adjacent structure. The installation of ADA accessible ramps and other pedestrian features (to be discussed further in this report) offers an inclusive and pedestrian-friendly space, which also operates as a buffer between the parking area and the former bank building. This is proposed without negatively impacting the historic value of the Phoenix Bank of Nansemond historic structure and the unified feel in the district. The installation of the proposed parking lot on the eastern side of the Phoenix Bank of Nansemond also assures compliance with the Historic District guidelines. Pedestrian and landscaping improvements: The applicant is proposing a series of pedestrian and landscaping improvements that would revitalize the subject property and offer both a pedestrian-friendly area adjacent to the parking lot that would serve the Phoenix Bank of Nansemond structure, as well as a small plaza for the neighborhood that includes trees, shrubs, additional street lighting, and an interpretative sign . Hence, the applicant is proposing to install a concrete sidewalk to create a pedestrian area, install 2 Dominion Energy 150W EQ. LED 40K Type 3 Cutoff Colonial Mounted at 14 feet high, installing 8 tree wells in the pedestrian area/sidewalk , installing sod/turf between the pedestrian area/sidewalk and the parking area, and planting 9 Bosque Elms, 2 Sawtooth Oak, and 21 shrubs (Dwarf Burford Holly) on the subject property. Per Section 31-413(f)(1)D, the proposed pedestrian, landscaping , and lighting improvements do not adversely affect the primary character of the district or the setting of structures and premises of substantial public interest. Per Section 31 -413(g)(2), all the materials and features, such as the trees, sod, Colonial-style lighting poles, and concrete, are considered appropriate and already present in the historic district. All landscaping and lighting features are compatible with the design, development standards, and criteria as included in the City’s adopted Historic Dis trict Design Guidelines. Per Chapters 4 and 5 of the Historic District guidelines, and considering the recommendations by the Secretary of the Interior, the staff finds that the proposed concrete sidewalk with tree wells, the HLC2026-00012 August 13, 2026 Page 6 “Colonial Mounted” street light pole, and the plantings (sod, shrubs, and trees) are consistent with the Historic District character, thus offering an unified feel to the streetscape, are compatible with the materials and architecture of the adjacent Phoenix Bank of Nansemond and other structures in the vicinity; for reference, the “Colonial Mounted” street light pole presents a design that it is a common streetscape feature throughout the Historic District and other sections of the Downtown. The arrangement of the landscaping and lighting features (as well as of the parking lot) is consistent with those on the same street block and accomplishes the goal of retaining the historic character of the streetscape and the rhythm of solids and voids along the street. The proposed improvements, as a whole, positively contribute to the transition from the public right of way to the private/commercial and institutional uses in the adjacent parcels . These improvements have compatible materials, colors, and features with those present in the Historic District, and simultaneously enhance East Washington Street’s streetscape while providing safe and accessible pedestrian-friendly access to the Phoenix Bank of Nansemond. Lastly, the proposed improvements are designed in a manner that they are unobtrusive to the Phoenix Bank of Nansemond building, and to assure the preservation of the historic relationship between the former bank structure, adjacent structures, and the overall landscape. Compliance with barrier-free access requirements is also proposed in such a manner that the Phoenix Bank of Nansemond’s character-defining spaces, features, and finishes are preserved. Recommendation In sum, staff have reviewed the proposed actions with respect to the applicable requirements of the HC Overlay zoning district and determined that the proposed project meets them. It is staff's opinion that improving the subject property, adjacent to the Phoenix Bank of Nansemond, with an eight-space parking lot, a pedestrian -friendly area and sidewalk, and landscaping, is appropriate because it aligns with the standards set by the Guidelines and by the UDO, as well as follows the recommendations set by the Secretary of the Interior’s Standards for Rehabilitation. Based on the above findings-of-fact and conditions outlined above, staff recommends approval of a Certificate of Appropriateness for the request sought under HLC2026-00012 for the development of a parking lot with eight spaces (inclusive of one accessible space), installation of concrete sidewalk and pedestrian area, curb and gutter, and landscaping: which includes installing eight tree wells in the pedestrian area/sidewalk, installing sod/turf between the pedestrian area/sidewalk and the parking area, and planting nine Bosque Elms, two Sawtooth Oak, and twenty-one shrubs (Dwarf Burford Holly). Staff would also like to clarify that, per the Historic Landmark Commission Guidelines (HLC Guidelines), the non-illuminated interpretative sign listed in the application and shown on the site plan was administratively approved on July 14th, 2026, under case HLC2026-00013. Therefore, staff recommend approval of the following actions as summarized below in regard to HLC2026-00012 and as further detailed and specified in the COA application: • Paving the existing gravel surface with standard-duty asphalt. HLC2026-00012 August 13, 2026 Page 7 • Mark a total of 8 parking spaces (including 1 ADA accessible parking space). • Install 6” concrete curb per Virginia Department of Transportation (VDOT) standards. • Install gutter per HRPD standards. • ADA accessible ramps with detectable warning surface per VDOT standards. • Install a concrete sidewalk to create a pedestrian area. • Install 2 Dominion Energy 150W EQ. LED 40K Type 3 Cutoff Colonial Mounted at 14 FT. • Install 8 tree wells in the pedestrian area/sidewalk. • Install sod/turf between the pedestrian area/sidewalk and the parking area. • Plant 9 Bosque Elms, 2 Sawtooth Oak, and 21 shrubs (Dwarf Burford Holly). Attachments • Site Maps • Narrative • Site Photography • Site Plan • Interpretative Sign • Planting Plan • Planting Plan Details • Lighting Plan • Lighting Plan Details Sources: Esri, TomTom, Garmin, FAO, NOAA, USGS, © OpenStreetMap contributors, and the GIS User Community 0 1.5 3 4.5 60.75 Miles ^_ Author: KOSSAI Date: 07-06-2026 ± GENERAL LOCATION MAP HLC2026-00012 Subject Property VILLAGE TRADITIONAL NEIGHBORHOOD SUBURBAN NEIGHBORHOOD RIGHT OF WAY RURAL NEIGHBORHOOD RURAL CONSERVATION RURAL AGRICULTURE PARKS AND OPEN SPACE OFFICE/INSTITUTIONAL MIXED USE CORE MULTIFAMILY NEIGHBORHOOD Employment Center COMMERCIAL CORRIDOR Central Growth Area ^_ SUBJECT PROPERTY E WASHINGTON ST HOLLAD AY ST LIB ERT YS T HALLA VE N & W AVE COUNTY ST TYNES ST 34G25(A)*5 353650000 0 60 120 180 24030 Feet EXHIBIT B Subject Property Author: KOSSAI Date: 07-06-2026 ± PROPERTY MAP HLC2026-00012 E WASHINGTON ST HOLLADAY ST HALL AV E LIBERTY ST COUNTY ST N & W AVE TYNES ST RM RM FRRD M-2 CBD CBD 34G25(A)*5353650000 0 60 120 180 24030 Feet Subject Property Image: Suffolk Pictometry 2024 Author: KOSSAI Date: 07-06-2026 ± ZONING / LAND USE MAP HLC2026-00012 N MAIN ST MARKET ST ECONS TANCE RD W W ASHINGTON ST CEDAR ST E WASHINGTON ST YORK ST WELLONS ST CAROLINA RD FAYETTE ST N SARATOGA ST FAYETTEST PITCHKETTLE RD SMITH ST MARYLAND AVE PITCHKETTLEVILLAGE ST JACKSON ST KATHERINE ST CULLODEN ST S SARATOGA ST WHITE MARSH RD JOHNSON AVE W CONSTANCE RD BANK ST CAROLINA RD ELEY CT FACTORY ST BUTE ST W FINNEY AVE RIVER POINT DR LINDEN AVE MOUNT HOREB ST NEWPORT ST FREENEY AVE MORGAN ST MILITARY RD HENLEYPL BANK ST EXT AZALEA CT GARFIELD AVE JOHNSON AVE MULBERRY ST WESTERN AVE NANSEMOND AVE CHURCH ST HALL AVE HILL ST CEDAR ST SPUR BEECH ST CAMPAVE YORK CT DAYST TYNES ST OAK ST E PINNER ST CHERRY ST BROOK AVE PINE ST SPRING ST OAKLAND ST RIVER POINT DR MADISON AVE POPLAR AVE FOREST HILL CRES N BROAD ST S DIVISION ST MOUNT SINAI ST NANSEMOND AVE TRADD ST DUMVILLE LN ORCHARD AVE GRAYSON CT CENTRAL AVE RIVERVIEW CT BOAT ST CAUSEY AVE KENNEDYCT CLARYS DR BETHLEHEM ST JOHNSONAVE MASON AVE HIGHLAND AVE OAKDALE TER PARKWAY ABRAHAM ST NORTH ST WILSON ST RENOST S BROAD ST MAHAN ST VIRGINIA AVE VIRGINIA AVE S MAIN ST POLKST RICHARDSON ST ASHLEY AVE LINDEN AVE KNIGHTST CANNON ST PITCHKETTLE RD RAILROAD AVE DUKE ST TERRACE CT PINNER ST HOLLADAY ST W RIVERVIEW DR COLLEGE CT SECOND AVE GRANBY ST SUNSETAVE COLLIEAVE FIRST AVE GRACE ST THIRD AVE WALNUT ST SECOND AVE MAPLE ST MULBERRY ST CAUSEY AVE PENDER ST GLOUCEST ER ST N DIVISION ST RIDLEY ST LINCOLN AVE BOSLEY AVE LEXINGTONAVE FORT ST VAN BUREN AVE JEFFERSON ST ADAMS STLAKESIDE ST EUGENIA ST KINGSBORO ST ALLEN ST GITTINGS ST ELIZABETH ST PARK RD JOHNSON LN DOGWOOD LN FINNEY AVE BATTERY AVEBROOK AVE FREEMASON ST HOWARD PL CAROLINA AVE NEVADA ST LEE ST N & W AVE COUNTY ST WILLOWST S BROAD ST SPRUCE ST SAINT JAMES AVE PEARL ST COMMERCE ST SOUTH ST N LLOYD ST JONES ST DUMVILLE AVE CHARLES ST LINDEN AVE LINDEN AVE BREWER AVE FOREST ST W FINNEYAVE WARWICKST N CAPITAL ST SAINT JAMES AVE FRANKLIN ST CHESTNUT ST PINE ST ROANOKE ST COMMERCE ST FOURTH ST CLAY ST HENRY ST RAILROAD AVE LIBERTY ST N DIVISION ST BUTLER AVE N SARATOGA ST DARDEN AVE N LLOYD ST JEFFERSON ST ERIVERVIEW DR HALIFAX ST LOCUST ST SHIPWRIGHT LN PRENTIS ST E RIVERVIEW DR FAIRGROUNDS LN E CONSTANCE RD ECONSTAN CE RD MOORE AVE NANSEMOND RIVERLAKE MEADE Disclaimer: THE CITY OF SUFFOLK MAKES NO WARRANTY, REPRESENTATION, OR GUARANTEE OF ANY KIND REGARDING EITHER ANY MAPS OR OTHER INFORMATION PROVIDED HEREIN OR THE SOURCES OF SUCH MAPS OR OTHER INFORMATION. THE CITY OF SUFFOLK SPECIFICALLY DISCLAIMS ALL REPRESENTATIONS OR WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILIY AND FITNESS FOR A PARTICULAR PURPOSE. The City of Suffolk assumes no liability for any errors, omissions, or inaccuracies in the information provided regardless of the cause of such or for any decision made , action taken, or action not taken by the user in reliance upon any maps or information provided herein. Parcel and Zoning information has been developed to provide a graphic representation of the Real Estate Property Tax Maps. The boundaries of any parcel may have been adjusted to provide a more visually pleasing presentation. User should refer to the instrument of transfer (deed or plat) for legal boundary location and perimeter or area measurements. Amended 8/16/2011 by Ordinance No. 11-O-073 0 0.1 0.2 0.3 0.40.05 Miles SCALE: 1:10,000 Legend BUILDING FOOTPRINTS SUFFOLK HISTORIC CONSERVATION OVERLAY NATIONAL REGISTER OF HISTORIC DISTRICTS ORIGINAL SUFFOLK DISTRICT (1987) NORTH MAIN STREET DISTRICT EXTENSION (1998) EAST WASHINGTON STREET DISTRICT (2002) WEST END DISTRICT (2004) WEST END DISTRICT EXPANSION (2004) SUFFOLK DISTRICT EXPANSION (2004) CEDAR HILL DISTRICT (2006) ^_ Author: KOSSAI Date: 07-06-2026 μ Suffolk Historic Conservation Overlay District & National Register GENERAL LOCATION MAP HLC2026-00012 Subject Property S16°09'27"W 88.01' (FIELD) S16°10'58"W 87.87' (PLAT) N74°14'10"W (FIELD) N74°14'35"W 64.82' (PLAT) S16°08'10"W 78.63' (FIELD) S15°59'54"W 78.70' (PLAT) S68°15'04"E (FIELD) S68°18'42"E 89.14' (PLAT) N16°11'25"E 88.89' (FIELD) N16°10'58"E 88.82' (PLAT) N16°20'03"E (FIELD) N16°10'58"E 89.15' (PLAT) S16°19'28"W (FIELD) S16°10'58"W 87.12' (PLAT) N73°06'50"W 24.38' (FIELD)N73°04'28"W 24.36' (PLAT) S68°21'19"E (FIELD) S68°18'42"E 24.47' (PLAT) STM #01 STM #02 8" CLAY 6" CLAY 8" CLAY 8" CLAY 8" CLAY SAN #02 SAN #03 CITY OF SUFFOLK, VIRGINIA (GRANTEE) 0.267 ACRE (PLAT) ACCOUNT # 353650000 TAX MAP #34G25(A)*5 ZONING: FRRD (FAIRGROUNDS REVITALIZATION AND REDEVELOPMENT DISTRICT); ALSO HISTORIC OVERLAY DISTRICT USE CODE: 740V - LOCAL GOVERNMENT NOW OR FORMERLY WILTON L & SHIRLEY B DAY ACCOUNT # 351578000 TAX MAP #34G25(A)6*8 ZONING: FRRD (FAIRGROUNDS REVITALIZATION AND REDEVELOPMENT DISTRICT); ALSO HISTORIC OVERLAY DISTRICT (PARTIAL) USE CODE: 344C - OFFICE BUILDING NOW OR FORMERLY CARLITO HAMLIN ACCOUNT # 353306000 TAX MAP #34G25(A)*2 ZONING: FRRD (FAIRGROUNDS REVITALIZATION AND REDEVELOPMENT DISTRICT); ALSO HISTORIC OVERLAY DISTRICT USE CODE: 353C - RETAIL STORE 01 02 NOW OR FORMERLY CARLITO HAMLIN ACCOUNT # 353306000 TAX MAP #34G25(A)*2 ZONING: FRRD (FAIRGROUNDS REVITALIZATION AND REDEVELOPMENT DISTRICT); ALSO HISTORIC OVERLAY DISTRICT USE CODE: 353C - RETAIL STORE CITY OF SUFFOLK, VIRGINIA (GRANTEE) INSTRUMENT #060002379 RECORDED FEBRUARY 2, 2006 GRANTOR: SUFFOLK REDEVELOPMENT AND HOUSING AUTHORITY INSTRUMENT #060124420 (PLAT) 0.267 ACRE (PLAT) ACCOUNT # 353650000 TAX MAP #34G25(A)*5 ZONING: FRRD (FAIRGROUNDS REVITALIZATION AND REDEVELOPMENT DISTRICT); ALSO HISTORIC OVERLAY DISTRICT USE CODE: 740V - LOCAL GOVERNMENT TYNES STREET ASPHALT PAVEMENT 50' RIGHT-OF-WAY (INST. #060124420) EAST WASHINGTON STREET ASPHALT PAVEMENT50' RIGHT-OF-WAY(INST. #060124420) EAST WASHINGTON STREET ASPHALT PAVEMENT50' RIGHT-OF-WAY(INST. #060124420) CITY OF SUFFOLK, VIRGINIA (GRANTEE) 0.267 ACRE (PLAT) ACCOUNT # 353650000 TAX MAP #34G25(A)*5 ZONING: FRRD (FAIRGROUNDS REVITALIZATION AND REDEVELOPMENT DISTRICT); ALSO HISTORIC OVERLAY DISTRICT USE CODE: 740V - LOCAL GOVERNMENT S16°08'110"W 78.63' (FIELD) S16°08'111110"W 78.63' (FIELD) S16°08'110"W 78.63' (FIELD) S15°59'545454544"W 78.70' (PLAT) 15 59 5444"W CITY OF SUFFOLK, VIRGINIA (GRANTEE) 0.049 ACRE (PLAT) ACCOUNT # 352674500TAX MAP #34G25(A)*3 ZONING: FRRD (FAIRGROUNDS REVITALIZATION AND REDEVELOPMENT DISTRICT); ALSO HISTORIC OVERLAY DISTRICT USE CODE: 740C - LOCAL GOVERNMENT 02 CITY OF SUFFOLK, VIRGINIA (GRANTEE) 0.010 ACRE (GIS) ACCOUNT # 350866200TAX MAP #34G25(A)*7 ZONING: FRRD (FAIRGROUNDS REVITALIZATION AND REDEVELOPMENT DISTRICT); ALSO HISTORIC OVERLAY DISTRICT USE CODE: 740V - LOCAL GOVERNMENT 01 SUFFOLK PHOENIX BANK PLAZA PREPARED FOR WOOLPERT SITE PLAN CS100 © SITE LEGEND NORTH PAVEMENT SECTION NOTE: A-101 D4 A-101 D2 24" x 36" GRAPHIC PANEL WITH FRAME GROUND LEVEL 0' - 0" 1' - 4" 4" 2' - 4" 4' - 0" 3' - 0" 2" x 4" SQUARE TUBING WELDED TO EACH SIDE FRAME 4 (1/2") NUTS AND BOLTS FASTEN 8" ALUM. AND STEEL BASE PLATES 24" x 36" GRAPHIC PANEL WITH FRAME 2" 3' - 0" 2" 3' - 4" 2" x 4" SQUARE STEEL MOUNTING POSTS WELDED TO 8" STEEL BASE PLATE 2" X 4" SQUARE ALUM. TUBING WELDED TO INTERPRETIVE SIGN FRAME WITH 8" SQUARE ALUMINUM BASE PLATE GROUND LEVEL 0' - 0" 30.00° ARCHITECTURE ENGINEERING GEOSPATIALɕɕ 4454 IDEA CENTER BOULEVARD DAYTON, OH 45430-1500 937.461.5660 1 2 3 4 5 6 7 A B C D E ISSUANCE SCHEDULE SHEET NAME: PROJECT NO: DATE ISSUED: NUMBER DATE DESCRIPTION SHEET NO: DESIGNED BY: DRAWN BY: CHECKED BY: GENERAL NOTES: Autodesk Docs://City of Suffolk VA -Projects HUB_R24/_W_10015069_Phoenix Bank Plaza_Historic Sign_R24.rvt 3/19/2026 8:49:46 AM INTERPRETIVE SIGN PLAN AND ELEVATIONS A-101 ND JM ND 10015069.09 03/20/2026 PHOENIX BANK PLAZA CITY OF SUFFOLK, VA 341 E WASHINGTON ST, SUFFOLK, VA 1/2" = 1'-0" INTERPRETIVE SIGN - PLAN VIEWD1 1/2" = 1'-0" FRONT ELEVATIOND2 1/2" = 1'-0" SIDE ELEVATIOND4 6" = 1'-0" 24" x 36" GRAPHIC PANEL - BASIS OF DESIGNA1 0 1'6" 2' 3' 4' 5' 6' 1/2"=1'-0" GRAPHIC SCALE 0 2" 3"1" 6" 6"=1'-0" 1. REFER TO CIVIL PLANS FOR DEMOLITION AND NEW CONSTRUCTION GENERAL NOTES. 2. REFER TO CIVIL PLANS FOR ALL SITE WORK. 3. GRAPHIC PANEL SIGN SHOWN FOR REFERENCE ONLY. PANEL TO BE DESIGNED BY INTERPRETIVE SIGN MANUFACTURER AND SUBMITTED AS A SHOP DRAWING TO BE APPROVED BY ARCHITECT PRIOR TO FABRICATION. 4. CONTRACTOR TO NOTIFY ARCHITECT OF ANY DISCREPANCIES PRIOR TO COMMENCING WORK. Lic. No. 013830 -$621$0,//(5 L OC INIGRIVFO HT AEWNOMM A A HCR DE CERT IIF CET T I -$6216-$66666-$6666$6--$6$$66-$6--$$6--$$$$$ $0,//(5 OOO R IIIIIIIII VVVVVVVVVVVVVVVVVV F E W E N W W OOOOO NNNN N M O O MM O O M 9:23:37 AM 03/19/2026 Lic. No. 0401013830 03/20/2026 S16°09'27"W 88.01' (FIELD) S16°10'58"W 87.87' (PLAT) N74°14'10"W (FIELD) N74°14'35"W 64.82' (PLAT) S16°08'10"W 78.63' (FIELD) S15°59'54"W 78.70' (PLAT) S68°15'04"E (FIELD) S68°18'42"E 89.14' (PLAT) N16°11'25"E 88.89' (FIELD) N16°10'58"E 88.82' (PLAT) N16°20'03"E (FIELD) N16°10'58"E 89.15' (PLAT) S16°19'28"W (FIELD) S16°10'58"W 87.12' (PLAT) N73°06'50"W 24.38' (FIELD)N73°04'28"W 24.36' (PLAT) S68°21'19"E (FIELD) S68°18'42"E 24.47' (PLAT) STM #01 STM #02 8" CLAY 6" CLAY 8" CLAY 8" CLAY 8" CLAY SAN #02 SAN #03 CITY OF SUFFOLK, VIRGINIA (GRANTEE) 0.267 ACRE (PLAT) ACCOUNT # 353650000 TAX MAP #34G25(A)*5 ZONING: FRRD (FAIRGROUNDS REVITALIZATION AND REDEVELOPMENT DISTRICT); ALSO HISTORIC OVERLAY DISTRICT USE CODE: 740V - LOCAL GOVERNMENT NOW OR FORMERLY WILTON L & SHIRLEY B DAY ACCOUNT # 351578000 TAX MAP #34G25(A)6*8 ZONING: FRRD (FAIRGROUNDS REVITALIZATION AND REDEVELOPMENT DISTRICT); ALSO HISTORIC OVERLAY DISTRICT (PARTIAL) USE CODE: 344C - OFFICE BUILDING NOW OR FORMERLY CARLITO HAMLIN ACCOUNT # 353306000 TAX MAP #34G25(A)*2 ZONING: FRRD (FAIRGROUNDS REVITALIZATION AND REDEVELOPMENT DISTRICT); ALSO HISTORIC OVERLAY DISTRICT USE CODE: 353C - RETAIL STORE 02 NOW OR FORMERLY CARLITO HAMLIN ACCOUNT # 353306000 TAX MAP #34G25(A)*2 ZONING: FRRD (FAIRGROUNDS REVITALIZATION AND REDEVELOPMENT DISTRICT); ALSO HISTORIC OVERLAY DISTRICT USE CODE: 353C - RETAIL STORE TYNES STREET ASPHALT PAVEMENT 50' RIGHT-OF-WAY (INST. #060124420) EAST WASHINGTON STREET ASPHALT PAVEMENT50' RIGHT-OF-WAY(INST. #060124420) EAST WASHINGTON STREET ASPHALT PAVEMENT50' RIGHT-OF-WAY(INST. #060124420) (1) QA (1) UP (1) QA (8) UB (1) ZG (5) LL (5) LL (5) LL (5) LL (1) ZG (5) LL (5) LL (2) ZG (448 sf) SOD (730 sf) SEED (644 sf) SOD (81 sf) SOD (1) EX-1 (1) EX-1 (21) IC (762 sf) SOD (1) EX-2 CODE QTY BOTANICAL NAME COMMON NAME ROOT CAL. TREES QA 2 QUERCUS ACUTISSIMA SAWTOOTH OAK B&B 1.5"-2" CAL. MIN. UB 8 ULMUS PARVIFOLIA `BOSQUE` BOSQUE ELM B&B 1.5"-2" CAL. MIN. UP 1 ULMUS PARVIFOLIA `EVERCLEAR` BOSQUE ELM B&B 1.5"-2" CAL. MIN. ZG 4 ZELKOVA SERRATA `GREEN VASE` GREEN VASE SAWLEAF ZELKOVA B & B 1.5"-2" CAL. MIN. EXISTING TREES EX-2 1 ACER SP. TO REMAIN IN PLACE. MAPLE EXISTING EX-1 2 ZELKOVA SERRATA TO REMAIN IN PLACE. ZELKOVA EXISTING CODE QTY BOTANICAL NAME COMMON NAME ROOT SIZE SHRUBS IC 21 ILEX CORNUTA `BURFORDII NANA` DWARF BURFORD HOLLY CONT. 24" HT. MIN. SYMBOL CODE QTY BOTANICAL NAME COMMON NAME CONT SPACING SPACING GROUND COVERS LL 30 LIRIOPE MUSCARI `BIG BLUE BIG BLUE LILY TURF 1 GAL 24" o.c. SEED 730 SF SEED TURF SEED SEED SH 734 SF SHREDDED HARDWOOD MULCH BULK SOD 1,935 SF SOD SOD SHALL BE HYBRID BERMUDA. TAHOMA 31 OR EQUAL. TURF SOD PLANT SCHEDULE KEYNOTES LANDSCAPE NOTES PLANT SUBSTITUTIONS EXISTING UTILITIES CITY OF SUFFOLK LANDSCAPE NOTES SUFFOLK PHOENIX BANK PLAZA PREPARED FOR WOOLPERT PLANTING PLAN CP100 © NORTH NOTE: SUFFOLK PHOENIX BANK PLAZA PREPARED FOR WOOLPERT PLANTING PLAN DETAILS CP500 © CLEANLINE INSTALLATION INSTRUCTIONS 1. Dig landscape trench 1" (25mm) deeper than the edging being set. 2. Set the edging into the landscape trench with the top 1/2" (12.5cm) above what will become the compacted finish grade. (The installer can connect the adjacent sections of the edging prior to or after the sections are placed in the trench.) Where connections are needed on curves, the installer will find that connecting sections prior to installing will allow for faster completion. 3. Start at the beginning of the bed area and begin driving the 12" (30.5cm) aluminum stakes. (NOTE: There are more loops per section than stakes. The additional loops are provided for greater versatility of staking based on the design and application.) 4. Snap down the adjacent sections. (See ISOMETRIC VIEW A) 5. At the end of the bed area, cut the section to the desired length and stake down. Begin your next bed area with the remaining portion of the cut section. FORMING ANGLES: Cut the bottom of the edging halfway up using a hacksaw, lay on a hard surface placing a brick or 4 x 4 over the cut. 6. Bend up to the desired angle using a hammer to stiffen angle. This forms a 1/2" radius on top avoiding sharp corners. area, cut the section to the desired length and stake down. Begin your next bed area with the remaining portion of the cut section. (See Diagram B) FORMING ANGLES: Cut the bottom of the edging halfway up using a hacksaw, lay on a hard surface placing a brick or 4 x 4 over the cut. Bend up to the desired angle using a hammer to stiffen angle. This forms a 1/2" radius on top avoiding sharp corners. PERMALOC CLEANLINE COMMERCIAL GRADE ALUMINUM LANDSCAPE EDGING NOTE: ALUMINUM EDGING SHALL ONLY BE USED TO EDGE RIVER ROCK MULCH BEDS. ® PERMALOC CORPORATION 13505 BARRY ST HOLLAND, MI 49424 TOLL FREE: 1-800-356-9660 PHONE: (616) 399-9600 FAX: (616) 399-9770 www.permaloc.com ISOMETRIC VIEW A SIDE VIEW PLANTING SPECIFICATIONS 1. SOILS TESTING A.All soil testing shall be done at the contractor's expense. soil tests shall be conducted by a state laboratory or recognized commercial laboratory. each sample shall be extracted from a six-inch deep core and prepared in accordance with recommendations of the soil-testing laboratory. B.each soils test shall determine soil texture / particle size, organic matter (OM), soil pH, buffer pH, nitrogen (N), phosphorus (P), potassium (K), calcium (Ca), iron (Fe), boron (B), zinc (Zn), copper (Cu), magnesium (Mg), manganese (Mn), sulfur (S), sodium (Na), calculated cation exchange capacity (CEC), excess carbonate, electrical conductivity (EC) and total dissolved solids (TDS), sodium adsorption ratio (SAR), AND soluble salts. C.All new soils provided from off-site sources, obtain one soil test for each soil source per 500 cubic yards of soil and submit soil test results and soil amendment recommendations to to the owner and engineer of record for review and acceptance prior to distributing and amending soil. D.For all existing stockpiled topsoil to be redistributed on site, obtain one soil test per 500 cubic yards of soil prior to application. submit soil test results and soil amendment recommendations to the owner and engineer of record for review and acceptance prior to redistributing and amending soil. 2. DELIVERY, HANDLING, AND STORAGE: D. Deliver packaged materials in manufacturer's unopened containers or bundles, fully identified with name, brand, type, weight, and analysis. Store packaged materials in such a manner as to prevent damage or intrusion of foreign matter. E. Dig balled and burlapped (B& B) plants with firm, natural balls of earth, of a diameter not less than recommended by the American Standard for Nursery Stock, and of sufficient depth to include the fibrous and feeding roots. B&B plants will not be accepted if the ball is cracked or broken before or during planting operation. F. Deliver trees and shrubs after preparations for planting have been completed. Do not bend, bind, or tie trees or shrubs in such a manner as to damage bark, break branches or destroy natural shape. If planting is delayed more than 6 hours after delivery, set trees and shrubs in shade, protect from weather and mechanical damage, and keep roots moist by heeling-in bare root stock and covering plant balls with soil, peat moss or other acceptable material for balled stock. Plants shall be kept well watered and shall not remain unplanted for longer than ten (10) days after delivery. G. Plants shall be lifted and handled from the bottom of the ball only. H. Do not remove container-grown stock from containers until planting time. 3. DRAINAGE: Before planting, determine that areas to receive plant material have adequate subdrainage. A. The landscape contractor is responsible for drainage tests as necessary to identify any problems prior to beginning planting operations. Upon commencement of planting operations the landscape contractor assumes responsibility for soil conditions. B. Dig planting pits to full depth and dimensions indicated on drawings. C. At bottom of planting pit, excavate rectangular pit 12 inches by 12 inches by 18 inches deep. Quickly pour water into pit to a depth of 6 inches (approximately 3-3 3/4 gallon). Note time required for water to be completely absorbed. Divide time noted by 6 to achieve average rate of absorption for 1 inch of water. Where rate of absorption exceeds 60 minutes per inch, notify owner immediately for directions on how to proceed. 4. PLANTING DATES: Planting shall be done only within the following dates except as approved by Owner. A. Deciduous Trees and Shrubs: March 1 to May 31 and October 15 to December 15. B. Evergreen Trees, Shrubs and Vines: March 1 to May 31 and September 1 to November 15. C. All plant material shall be guaranteed by the Contractor for a period of 1 year from the date final acceptance to be in good, healthy and flourishing condition. 5. MATERIALS FOR PLANTING: A. Topsoil: shall be a fertile, friable natural loam, uniform in composition, free of stones, lumps, plants and their roots, debris and other extraneous matter over 1 inch in diameter, capable of sustaining vigorous plant growth. Soil shall be harvested at a single source from the O and/or A horizons of the soil profile. 1) Topsoil shall have a pH range of 5.5 to 7.5. 2) Topsoil shall contain 1.5-5% organic matter by dry weight . 3) Soil Texture: sandy loam, sandy clay loam with the following particle size distribution: Gravel Less than 10% Silt 15-30% Clay 20-35% Chemical Levels shall be: Magnesium Mg100+ units Phosphorus P205 150+ units Potassium - K20 120+ units 4) Soluble Salts/ Conductivity - Not to exceed 900 ppm/0.9 mmhos/cm (in soil); not to exceed 3000 ppm/2.5 mmhos/cm (in high organic mix) 5) Cation exchange capacity shall be a minimum of 8 meq/100g. B. Clay Loam to Sandy Clay Loam Soil: shall be a fertile, friable natural loam, uniform in composition, free of stones, lumps, plants and their roots, debris and other extraneous matter over 1 inch in diameter, capable of sustaining vigorous plant growth. 1) Soil shall have a pH range of 5.5 to 6.5. 2) Soil shall contain 2-5% organic content by volume. 3) Soil Texture: Clay loam to sandy clay loam with the following particle size distribution: Gravel Less than 10% Sand 20-50% Silt <35%% Clay 20-40% 4) Chemical Levels shall be: Magnesium Mg100+ units Phosphorus P205 150+ units Potassium - K20 120+ units 5) Soluble Salts/ Conductivity - Not to exceed 900 ppm/0.9 mmhos/cm (in soil); not to exceed 3000 ppm/2.5 mmhos/cm (in high organic mix) 6) Cation exchange capacity shall be 20-35 meq/100g. C. Compost: Compost shall be mature, stable, weed free, and produced by aerobic decomposition of organic matter. Compost feedstock shall be plant matter, such as high lignin forestry products or yard waste (leaves, brush and yard trimmings). 1) The product must not contain any visible refuse or other physical contaminants, substances toxic to plants, or over 5% sand, silt, clay or rock material by dry weight. 2) Compost shall be sampled and tested as required by the Seal of Testing Assurance Program of the United States Composting Council (USCC) and shall meet the physical requirements for compost as determined by USCC. 3) The product shall possess no objectionable odors. The product must meet all applicable USEPA CFR, Title 40, Part 503 Standards for Class A biosolids. 4) The moisture level shall be such that no visible water or dust is produced when handling the material. D. Composted Pine Bark Fines: Shall be approved composted, ground pine bark having no particle with a dimension greater than 3/4 inch. No more than 10% shall be wood. E. Sand: Shall be quartz based sharp concrete sand, ASTM C-33 Fine Aggregate, with a Fines Modulus Index between 2.8 and 3.2. F. Perlite: Coarse horticultural grade expanded, volcanic perlite. Maximum density shall be 8 lb./ft3. 1) pH shall be 6.5 to 7.5. 2) Perlite shall be meet the Perlite Institute's Standards for Gradation for Horticultural Perlite for Coarse Perlite with no more than 70% passing through a #16 Standard Sieve. G. Humus: Shall be mature, stable, weed free, and produced by aerobic decomposition of organic matter. Compost feedstock shall be plant matter, such as high lignin forestry products or yard waste (leaves, brush and yard trimmings). 1) Humus shall have a pH between 6 and 7.5. 2) Soluble Salt Concentration shall be less than 10dS/m. 3) Cation exchange capacity rate shall be 100-250. 4) The product must not contain any visible refuse or other physical contaminants, substances toxic to plants, or over 5% sand, silt, clay or rock material by dry weight. 5) The product shall possess no objectionable odors. The product must meet all applicable USEPA CFR, Title 40, Part 503 Standards for Class A biosolids. 6) The moisture level shall be such that no visible water or dust is produced when handling the material. H. Trace Elements: Shall be commercially available slow release materials containing zinc (Zn), Molybdenum (Mo), Copper (Cu), Boron (B), and Magnesium (Mn). I. Fertilizer: A commercial fertilizer for ornamental trees, shrubs and ground cover with an analysis of 10% Nitrogen, 6% Phosp horus and 4% Potassium shall be used. This fertilizer shall be granular with a minimum of 50% of the total Nitrogen in organic form. 14-14-14-Osmocote (or approved equal) shall be applied at a rate of 10 lbs. per square foot, tilled to a depth of 8 inch, shall be used for perennials. 6. PLANT MATERIALS: (Refer to the PLANT LIST on the drawings for specific types and quantities of plants): A. Plants shall be nursery grown in accordance with good horticultural practices. Plants shall either be obtained from local nurseries and/or others, which have soil and climatic conditions similar to those in the locality of the project. B. Plants shall be true to species and variety and unless specifically noted otherwise, all plants shall be of specimen quality, exceptionally heavy, symmetrical, tightly-knit plants, so trained or favored in their development and appearance as to be superior in form, number of branches, compactness and symmetry. C. Plants shall be sound, healthy and vigorous, well branched and densely foliated when in leaf, free of disease, insect pests, eggs or larvae and shall have healthy, well-developed root systems. They shall be free from physical damage or any conditions that would prevent thriving health and the desired appearance. D. Trees, which have a damaged or crooked leader, or multiple leaders, unless specified in the plant list, will be rejected. Trees with abrasion of the bark, sun scald, disfiguring knots, or pruning cuts more than 1 1/4 inch diameter which have not completely callused, will be rejected. E. Plants shall conform to measurements specified in the plant schedules except that plants larger than specified may be used if acceptable to the Landscape Architect or owner. Use of such plants shall not increase the contract price. If larger plants are accepted, the root ball shall be sized for the larger plant. F. Caliper Measurement: Shall be taken at a point on the trunk 6 inches above natural ground line for trees up to 4 inches diam eter, and at a point 12 inches above the natural ground line for trees over 4 inches diameter. G. Plants shall be measured when branches are in the normal position. Height and spread dimensions specified refer to the main body of the plant and not from branch tip to tip. 7. SOIL MIXING PROCEDURES: A. Topsoil used in sand/soil mixes shall be screened or shredded prior to mixing in sands. Maximum clod inclusion for soil mixes shall not exceed: Clod size (largest dimension) % of the soil mix volume Less than 1” Unlimited 1 to 3 inches 20% 3 to 6 inches 5% >6 inches Less than 2% A. Source material and soil mix stockpiles shall be protected from rain by covering with filter cloth. 8. INSPECTION: A. EXAMINE THE AREAS AND CONDITIONS WHERE SOIL MIX IS TO BE INSTALLED AND NOTIFY THE ENGINEER OF CONDITIONS DETRIMENTAL TO THE PROPER AND TIMELY COMPLETION OF THE WORK. DO NOT PROCEED WITH THE WORK UNTIL UNSATISFACTORY CONDITIONS ARE CORRECTED TO PERMIT PROPER INSTALLATION OF THE WORK. B. COOPERATE WITH OTHER CONTRACTORS AND TRADES WORKING IN AND ADJACENT TO OTHER WORK AREAS. EXAMINE DRAWINGS WHICH SHOW DEVELOPMENT OF ENTIRE PROJECT AND BECOME FAMILIAR WITH SCOPE OF OTHER WORK REQUIRED. 9. SOIL INSTALLATION - GENERAL PROCEDURES: G.IF SUBGRADE SOIL COMPACTION EXCEEDS 80%, EXISTING SOIL SHALL BE RIPPED TO A DEPTH OF 12 INCH TO ALLEVIATE COMPACTION WHICH HAS TAKEN PLACE DURING CONSTRUCTION. PRIOR TO LOOSENING OF SOIL, CONTRACTOR MUST LOCATE EXISTING UTILITIES AND COORDINATE WITH OWNER OR OWNERS REPRESENTATIVE ANY UNDERGROUND ELECTRIC LINES, DRAINAGE PIPES, CONDUITS, ETC. H. PREPARE THE SUBGRADE BY ROUGHENING THE TOP 3” OF THE SUBSOIL BY DRAGGING THE TEETH OF A BACKHOE BUCKET ACROSS THE SURFACE. I. BEGIN SOIL INSTALLATION AS SOON AS SUBSOIL IS PREPARED. USE LOW IMPACT EQUIPMENT WITH TRACK BELTS, LARGE TIRES, OR LOW TIRE PRESSURE TO LOWER COMPACTION AND SOIL DAMAGE DURING INSTALLATION. J. MONITOR COMPACTION DURING INSTALLATION AND LOOSEN SOILS AS NEEDED IF COMPACTION EXCEEDS 80%. 10. SOIL INSTALLATION - GENERAL PROCEDURES CONTINUED: K. Install specified soil in 12”-18” thick lifts. Compact each lift sufficiently to reduce settling but not enough to prevent the movement of water and feeder roots through the soil. The soils in each lift should feel firm to the foot in all areas and make only slight heel prints. 11. INSTALLATION OF SOIL MIX FOR LAWN AREAS ON GRADE: A. Soil Mix for Lawns on Grade: shall consist of 10% compost and 90% topsoil, by volume. These materials must meet specifications described in Paragraph 6. B. Loosen subgrade lawn areas to a minimum of 3”. Remove stones more than 1-1/2” in any dimension and sticks, roots, rubbish, and other extraneous matter. Limit preparation to areas which will be planted promptly after preparation. C. Spread soil mix for lawn areas on grade to a minimum depth of 4” as required to meet grade and elevations shown on drawings, after lightly rolling and natural settlement. Allow for sod thickness in areas to be sodded. 12. INSTALLATION OF SOIL MIX FOR TREE PITS ON GRADE A. Confirm that native subsoil drains at a rate of at least ½” per hour. If drainage is less than ½” per hour, provide subsurface drainage lines. B. Install 30-36” of Soil Mix for Tree Pit Backfill on Grade: 1) Shall consist of clay loam to sandy clay loam soil, sand, and composted pine bark fines at a rate of 5:5:1 to 10:5:1.5 to achieve the following: (a) Clay content of Soil Mix shall be 10-20% of the soil mix, by volume. (b) Minimum amount of coarse to medium sand in the mix shall be 55% (c) Minimum infiltration rate at 80-85% compaction shall be 1-3 inches per hour. C. Composted pine bark fines shall not exceed 10% of the total soil mix by volume. D. Till 4” of compost into the top 6” of the installed Soil Mix for Tree Pit Backfill on Grade. 13. INSTALLATION OF SOIL MIX FOR MULCHED SHRUB AND PERENNIAL BEDS: A. Confirm that native subsoil drains at a rate of at least ½” per hour. If drainage is less than ½” per hour, provide subsurface drainage lines. B. Install 4” of Soil Mix for Mulched Shrub and Perennial Beds on Grade: 1) Shall consist of clay loam to sandy clay loam soil, sand, and composted pine bark fines at a rate of 5:5:1 to 10:5:1.5 to achieve the following: (a) Clay content of Soil Mix shall be 10-20% of the soil mix, by volume. (b) Minimum amount of coarse to medium sand in the mix shall be 55% (c) Minimum infiltration rate at 80-85% compaction shall be 1-3 inches per hour. 2) Composted pine bark fines shall not exceed 10% of the total soil mix by volume. C. Till 4” of compost into the top 6” of the installed Soil Mix for Tree Pit Backfill on Grade. 14. GENERAL PLANT INSTALLATION: A. Excavation: Excavate all tree pits and planting areas to the width and depth shown in the planting details. B. Center plant in pit and orient for the best visual effect. Set plants plumb and hold rigidly in position until soil has been tamped firmly around root ball. C. Mulch within 48 hours after planting and after applying the pre-emergent herbicide, except ground cover areas (which shall have organic material placed before planting) with a 3" layer of mulch immediately after planting. All bed lines shall be cut with a smooth consistent edge to a minimum depth of 3 inches. Keep mulch out of the crowns of shrubs and off buildings, sidewalks, light standards, and other structures. D. All planting areas to conform to specified grades after full settlement has occurred and mulch has been applied. Provide saucers around tree pits as shown on planting details. Remove all tags, labels, strings, etc. from all plants. 15. MAINTENANCE AND GUARANTEE: A. The landscape contractor shall be responsible for maintaining his work until final acceptance by the owner or the owner's representative. Maintenance shall include watering, weeding, cultivating, mulching, removal of dead materials, resetting of plants to proper grades or upright positions, restoration of earth berms, and other necessary operations. adequate protection for lawn areas against trespassing during planting operations and against damage of any kind shall be provided. nothing in these notes is intended to relieve the contractor of his responsibility to repair existing lawn areas damaged by workmen engaged in the completion of this project. B. Inspection of the work to determine completion of the contract exclusive of the possible replacement of plantings during the warranty period, will be made by the owner or the owner's representative at the conclusion of the installation period upon written notice requesting such inspection. Request shall be submitted by contractor at least ten days prior to the anticipated date for inspection. After inspection, the contractor will be notified in writing by the owner or the owner's representative of acceptance of the work or, if there are any deficiencies, the contractor will be notified of the requirements necessary for completion of the work. Plantings shall not be considered accepted until all deficiencies have been corrected and approved in writing. C. Nursery stock shall be fully guaranteed for one full year. All plants that fail to make new growth from a dormant condition or that die during the first year after planting shall be replaced. All replacements shall conform with the original specifications as to size and type. All costs of replacements shall be borne by the contractor. D. The contractor shall be responsible for the removal of all unused materials, rubbish, debris, or plant material not planted from the site upon completion of his work. E. All other items necessary to make work complete shall be finalised prior to final inspection. 16. PERMANENT SODDING FOR LAWN AREAS: A. Sod shall be Tahoma hybrid Bermuda sod or equal. Sod shall only be installed during the warm season when Bermuda sod is actively growing. Out of season lawn shall be a temporary lawn of winter rye. B. Sod shall not be installed when ground is frozen. C. Sod and subsoil shall be kept moist until sod is fully established. D. Prior to laying sod contractor shall provide 4 inches of topsoil as specified on all areas to receive seed or sod. E. The contractor shall sod all areas within the contract limits that are not paved or planted and mulched as designated on the drawings unless specifically noted otherwise. F. The sod shall be green tag certified to meet local state plant board specifications, absolutely true to varietal type, and free from weeds, fungus, insects and disease of any kind. G. Sod panels shall be laid tightly together so as to make a solid sodded lawn area. Sod panels shall be laid in a staggered pattern. Sod shall be laid uniformly against the edges of all curbs and other hardscape elements, paved and planted areas. Immediately following sod laying, the lawn areas shall be rolled with a lawn roller customarily used for such purposes, and then thoroughly irrigated. After rolling of sod any voids created by rolling shall be filled with strips of sod and rolled. H. During delivery, prior to, and during the planting of the lawn areas, the sod panels shall at all times be protected from excessive drying and unnecessary exposure of the roots to the sun. Sod shall be installed immediately upon delivery to the site. Contractor shall ensure that all lawn areas to be sodded are fully prepared prior to having sod delivered to the site. If sod has to be stored overnight is shall be unrolled and stored so as not to be damaged by sweating or excessive heat and moisture. Sod shall not be left stacked or rolled. 17. PERMANENT SEEDING: A. Prior to seeding contractor shall provide and spread 4" of topsoil as specified on all areas to receive permanent seeding. B. Topsoil that has become hard and compacted before permanent seeding has been applied shall be scarified to prepare seed bed for receiving seed. C. The contractor shall seed all denuded areas and areas disturbed by construction that are not otherwise stabilized with paving, buildings, or planted and mulched within the contract limits, unless specifically noted otherwise. D. If a utility line is installed through a landscaped lawn the seeding shall be modified to restore ground cover comparable to the existing lawn I. Seeding includes seedbed preparation, liming, fertilizing, seeding, and mulching of disturbed areas. J. Seed shall be green tag certified and shall be labeled in accordance with the state laws and the U.S. Department of Agricultu re rules and regulations under the Federal Seed Act in effect on the date of invitations for bids. Bag tag figures are evidence of purity and germination. K. Lawn Seed varieties shall be an improved turf-type variety known to perform well in the project area. Seed mixture shall be chosen to ensure the development of plants during the season of planting, and to ensure future growth and permanent stabilization. Seed shall conform to the requirements of the Virginia Crop Improvement Association (VCIA). L. All seed shall conform to the current rules and regulations of the state where it is being used and shall be from the latest crop available.The seed shall be State-certified to meet Virginia seed certification standards and specifications, absolutely true to varietal type, and free from weeds, fungus, insects and disease of any kind. M.No seed will be accepted with a test date of more than 9 months before the delivery date to the site. N. Seed that has become wet, moldy, or otherwise damaged in transit or storage will not be accepted. The percent of noxious weed seed allowable shall be as defined in the current State laws relating to agricultural seeds. O. LIMING: Lime shall be applied separately and prior to the application of any fertilizer or seed and only on seedbeds, which have previously been prepared. The lime shall be worked into the top 3 inches of soil after which the seedbed shall again be properly graded and dressed to a smooth finish. Lime shall be applied at the rate specified by the soil test report recommendations. P. FERTILIZING: Following advance preparations and cleanup, fertilizer shall be uniformly spread at the rate specified in the soil test report recommendations. Q. SEEDING: Grass seed shall be sown at the rate specified in the permanent seeding schedule and notes immediately after fertilizing and the fertilizer and seed raked into the soil.Seeds shall be inoculated before mixing or sowing in accordance with the instructions of the seed provider and manufacturer of the inoculant. When seeding is required at other than the seasons shown in the permanent seeding schedule, a cover crop shall be sown by the same methods required for grass seeding and permanent seeding shall be sown during the following permanent seeding season. R. Sow seed with spreader or seeding machine. Do not broadcast or drop seed when wind velocity exceeds 5 mph. Evenly distribute seed by sowing equal quantities in two directions at right angles to each other. Do not seed against existing trees. S. Rake seed and fertilizer lightly into top 1/8 inch of soil and water with fine spray. T. MULCHING: Protect seeded areas with slopes not exceeding 3:1 by spreading straw mulch. Spread uniformly at a minimum rate of 2 tons/acre to form a continuous blanket 1-1/2 inches in loose thickness over seeded areas. Spread by hand, blower, or other suitable equipment. Protect slopes 3:1 and greater with erosion control mats and fasten as recommended by material manufacturer. U. Straw mulch material--Straw mulch shall consist of wheat, barley, oat or rye straw. The mulch material shall be air-dry, reasonably light in color, and shall not be musty, moldy, caked, or otherwise of low quality. The use of mulch that contains noxious weeds is not permitted. V. Other mulch materials--Mulching materials, such as wood cellulose fiber mulch, synthetic fiber mulch, netting, and mesh, are other mulching materials that may be required for specialized locations and conditions. These materials must be installed according to the manufacturer's recommendations for methods of application. W.After the seed has been properly covered, the seedbed shall be immediately compacted by means of an approved lawn roller weighing 40 to 65 pounds per foot of width for clay soil (or any soil having a tendency to pack) or weighing 150 to 200 pounds per foot of width for sandy or light soils. 3" 1" 5" PLANTING BED TRENCH EDGING NOTE: 1. TRENCH EDGE SHALL BE LOCATED BETWEEN PLANTING BED AND ALL TURF / SOD AREAS. 2. MAINTAIN POSITIVE DRAINAGE IN ALL PLANTING BEDS. 3. SEE NOTES THIS SHEET FOR TYPE OF MULCH. MULCH 3" DEPTH ® 17. LAWN MAINTENANCE: A. Within the contract limits, the contractor shall produce a dense, well established lawn. The contractor shall be responsible for maintaining the lawn until acceptance by the owner or owner's authorized representative. B. Maintenance shall include but may not be limited to watering, weeding, and fertilizing as necessary as well as the repair and re-sodding or re-seeding of all eroded, sunken or bare spots (larger than 12"x12") until certification of acceptability by the owner or owner's representative. Repaired sodding shall be accomplished as in the original work (including re-grading if necessary). 18. ACCEPTANCE: A stand of permanent lawn grass as specified shall be considered acceptable when the turf cover is at least 95%. The Contractor shall sod or overseed, and otherwise maintain the grassed areas until the stand of grass has reached a uniform height of 3 to 4 inches and a state of uniform species maturity. Annual grasses and grain weeds shall not be considered part of the cover percentage, and seeding stands shall not be considered acceptable until the stand reaches a state of uniform post-seeding maturity for the specified species. PERMANENT SEEDING SHALL BE green tag CERTIFIED AND SELECTED FROM THE CURRENT VIRGINIA TURFGRASS VARIETY RECOMMENDATIONS AS PUBLISHED BY VIRGINIA TECH, VIRGINIA COOPERATIVE EXTENSION. SEED SELECTED SHALL BE OF A VARIETY KNOWN TO PERFORM WELL IN THE PROJECT AREA AND SHALL BE OF A VARIETY THAT IS KNOWN TO BE TOLERANT OF FULL SUN, AND ONCE ESTABLISHED, TOLERANT OF PERIODS OF INFREQUENT RAINFALL. PERMANENT LAWN GRASS SEEDING OUTSIDE OF THE PREFERRED SEEDING DATES WILL NOT BE ACCEPTED UNTIL THE FOLLOWING GROWING SEASON AND ONLY WHEN AN ACCEPTABLE STAND OF PERMANENT GRASS IS ESTABLISHED AND ACCEPTED BY THE OWNER. SPRING AND FALL SEEDING: SEED SHALL CONSIST OF A BLEND OF THREE OF THE FOLLOWING VARIETIES KNOWN TO PERFORM WELL IN THE PROJECT AREA. SELECTED VARIETIES SHALL BE SEEDED AT THE SPECIFIED RATES PER ACRE. FOR ALL AREAS SEEDED WITH PERMANENT LAWN GRASS IN THE SPRING OR FALL (SEE SPECIFIED SEEDING DATES BELOW): TYPE OF GRASS SEEDING RATE SEEDING DATE TALL FESCUE 5 - 7 LBS./1000 SQ. FT. SPRING SEEDING: FEBRUARY 28, TO MAY 15. FALL SEEDING: AUGUST 1 TO NOVEMBER 1 NOTE: PREFERRED FESCUE SEEDING DATES ARE FROM AUGUST 1 TO NOVEMBER 1. 4TH MILLENNIUM SRP, ANNAPOLIS, AVENGER II4, AVENGER III, BIRMINGHAM1, BLACK TAIL, BLOODHOUND4, BULLSEYE1, BULLSEYE LTZ, CATALYST, CROSSFIRE 4, DAYBREAK, DEGAS, DRAGSTER, DYNAMITE G-LS, FANTASIA, FASTLANE, FAYETTE, FIREBIRD 2, FIRECRACKER G-LS, FIRECRACKER SLS, FIREHAWK SLT, FIRENZA II, FIREWALL4, GAZELLE II4, GOLD MEDALLION4, GRANDE 3, GTO, GUARDIAN 41, HEMI, HOUNDOG 84, INFERNO4, INTEGRITY4, JUSTICE4, LIFEGUARD, MAESTRO, MICHELANGELO, MONUMENT, MOONDANCE GLX, MUSTANG 44, PARAMOUNT, PENN RK44, PRO GOLD, RAPTOR III, REBEL IV4, REBEL V4, REBEL XLR4, REBOUNDER4, REFLECTION, REGENERATE, RENDITION RX4, ROCKWELL, ROWDY4, SALTILLO4, SCREAMER LS, SERENADE, SPYDER LS4, SPYDER 2LS, SR 8650, STANDOUT4, STEALTH, SUNSET GOLD4, SUPERSONIC, SYMPHONY, TECHNIQUE, TEMPLE, THOR, TITANIUM 2LS, TITANIUM G-LS, TITAN RX4, TRINITY, TURBO4, TURBO RZ4, VALKYRIE LS, WICHITA, AND XTREMEGREEN4. BATTLE HAWK, BENTLEY, BLADERUNNER 3, BONFIRE, BRAVO 2, CAPITAN, CLASH, ENDGAME, ESSENTIAL 2, ESTRENA, EXTRAVAGANZA, FAIRFIELD, FALCON SUPREME, FINELAWN SUPREME, GALACTIC, GALLARDO, GLX ACED, GLX REVIVE, GRO_PRO, HELLCAT GLR, HOUNDOG 9, KIZZLE, LAFAYETTE, MATISSE, MOTIF, NATURALLY GREEN, OKEEFE, ORIOLE, PADRE 2, PROVIDENCE, RACEWAY, RAPTOR LS, ROVER, ROWDIER, SR 8700, TALLADEGA II, TANK, TEACHER, TITAN GLX, TITAN MAX, TOUGH, TRIAD, VALSETZ, XANADU, AND ZION. SEED WITH THE FOLLOWING MIXTURE(S) FOR SPECIFIED DATES OUTSIDE THOSE LISTED FOR FESCUE ABOVE: TYPE OF GRASS SEEDING RATE SEEDING DATE BERMUDA 2 LBS./1000 SQ. FT.(HULLED SEED) MAY 15 - JUNE 30 ONLY THE FOLLOWING VARIETIES OF BERMUDA SHALL BE ACCEPTABLE: PRINCESS 77, ARDEN 154, MONACO, RIO, SUNQUEEN, SWI-10704, OR AS OTHERWISE LISTED ON THE VIRGINIA TURFGRASS VARIETY RECOMENDATIONS, LATEST EDITION AS PUBLISHED BY VIRGINIA COOPERATIVE EXTENSION. ALL SEED SHALL HAVE A MINIMUM PURITY OF 95% AND AN 85% GERMINATION RATE. CITY OF SUFFOLK LANDSCAPE NOTES STM #01 STM #02 SAN #02 SAN #03 TYNES STREET ASPHALT PAVEMENT 50' RIGHT-OF-WAY (INST. #060124420) EAST WASHINGTON STREET ASPHALT PAVEMENT50' RIGHT-OF-WAY(INST. #060124420) EAST WASHINGTON STREET ASPHALT PAVEMENT50' RIGHT-OF-WAY(INST. #060124420) 3.25.0 2.2 0.9 1.2 2.0 2.9 1.7 0.8 1.7 3.3 3.5 2.7 1.5 1.1 0.7 1.9 3.7 2.0 1.0 0.6 0.7 1.4 2.6 3.2 0.4 0.6 1.3 2.0 1.7 0.9 1.6 1.1 0.7 0.70.8 1.5 1.42.2 0.7 0.0 0.0 0.0 0.0 0.30.20.10.10.10.10.10.00.00.00.00.00.00.00.00.00.00.00.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.1 0.2 0.5 0.4 0.2 0.4 0.5 0.5 0.2 0.0 0.1 0.1 0.5 1.0 2.0 3.5 3.0 2.4 3.6 2.1 1.2 SUFFOLK PHOENIX BANK PLAZA PREPARED FOR WOOLPERT LIGHTING PLAN CL100 © NORTH 0.5FC (TYP.) PROPERTY BOUNDARY CALCULATION ZONE SIDEWALK PLAZA CALCULATION ZONE PARKING LOT CALCULATION ZONE PRPR EX EX EX LIGHTING GENERAL NOTES: 1. ALL PROPOSED LIGHT FIXTURES AND ALL NECESSARY LIGHTING FEEDER CIRCUITS (CONDUITS, CONDUCTORS, AND SERVICE CONNECTIONS) ARE TO BE INSTALLED BY DOMINION ENERGY. CONTRACTOR TO COORDINATE WITH DOMINION ENERGY FOR ALL PROPOSED LIGHTING INSTALLATION. 2. LIGHT POLE FOUNDATIONS TO EXTEND 6" ABOVE GRADE. CONTRACTOR TO SUBMIT FOUNDATION DESIGN TO ENGINEER FOR REVIEW. 3. ALL LIGHTS SHALL BE SHIELDED, FILTERED, AND DIRECTED TO MINIMIZE GLARE AND REDUCE LIGHT POLLUTION. 4. ALL LIGHTING FIXTURES USED MUST BE FULL CUT-OFF DESIGN FILTERED WITH A FLAT LENS AND PARALLEL TO THE GROUND. 5. SURVEY LABELS FROZEN ON THIS SHEET FOR CLARITY. SEE SHEETS SV100 AND SV101 FOR DETAILED INFORMATION REGARDING EXISTING STRUCTURES. ACCESSIBLE PARKING SIGN. SEE SHEET CS501 HISTORICAL SIGN. SEE SHEET A-101. SUFFOLK PHOENIX BANK PLAZA PREPARED FOR WOOLPERT LIGHTING PLAN DETAILS CL500 © EXISTING (EX) AND PROPOSED (PR) LIGHT FIXTURE SPECIFICATIONS EXISTING (EX) LIGHT FIXTURE SPECIFICATIONS PROPOSED (PR) LIGHT FIXTURE SPECIFICATIONS ADMINISTRATIVE APPROVALS March 2026 – July 2026 FILE NUMBER ADDRESS ALTERATIONS APPROVAL DATE HLC2026-00007 404 N. Main Street New metal roof 4/6/2026 HLC2026-00008 109 St James Avenue New roof over the front & rear porch 4/10/2026 HLC2026-00009 230 E. Washington Street Window replacement 5/18/2026 HLC2026-00010 213 Pearl Street Replace existing damaged roof shingles, replace the existing front entry door, replace the existing damaged windows, and to replace the existing vinyl siding 6/18/2026 HLC2026-00013 347 E. Washington Street Phoenix Bank Install a non-illuminated sign 7/14/2026 1 HLC PROPERTY MAINTENANCE CODE ENFORCEMENT UPDATE JULY, 2026 ADDRESS CODE VIOLATION(S) STATUS 223 BANK ST PROPERTY MAINTENANCE • WINDOWS DAMAGE • ROOF DAMAGE • DETERIORATED EXTERIOR WALL • INTERIOR SURFACE DAMAGE • DETERIORATED PORCH PROPERTY STILL IN VIOLATION PROPERTY IS NO LONGER FOR SALE THE CITY IS LOOKING INTO AVILIABLE OPTIONS FOR THE PROPERTY 112 W WASHINGTON ST PROPERTY MAINTENANCE • ELEVATORS IN DISREPAIR • FIRE / ELECTRICAL VIOLATIONS VACANT BUILDING OWNER HAVE MADE ALL REPAIRS FROM THE RECENT ACCIDENT. AND MAKING OTHER NECESSARY REPAIRS 221 BANK ST PROPERTY MAINTENANCE • PEELING/CHIPPING PAINT • INSECT SCREENS WORK HAS STARTED 318 BANK ST PROPERTY MAINTENANCE • PEELING PAINT • OVERHANG IN DISREPAIR • SURFACE COAT ROOF APPEARS WORK HAS STALLED A NEW PROPERTY MAINTENACE CASE WILL BE OPENED 222 BANK ST PROPERTY MAINTENANCE • FOUNDATION DAMAGE • BROKEN RETENTION WALL • BROKEN WINDOWS • DETERIORATING WOOD ON • OVERHANG PROPERTY IS A WORK IN PROGRESS 219 CLAY ST • A TREE FELL ON THE GARAGE NOTICE OF VIOLATION HAVE BEEN MAILED TO THE OWNER ON FILE TO REMOVE THE GARAGE July 31, 2026 Property Owner(s) Location Violation(s) Judgement Inspector Parvati LLC 213 Pearl St COA Violation- Wrong siding color Working with our office to fix the issue Davidson TOWNSEND, JEFFREY & RENNEE 108 N Main COA Violation- No Permit for sign NOV Issued Davidson 155 E WASHINGTON LLC 155 E WashingtCOA Violation- Painted Brick NOV Issued Davidson Zoning Case Activity Report

Source: City of Suffolk website. First collected Oct 26, 2026.