RecordWell Data

Historic Preservation / Design Review Commission — Agenda Packet

City of Stevens Point · Portage County · Historic Preservation and Design Review Commission · meeting of Jan 13, 2026 · Agenda packets

Open the original document More from City of Stevens Point

Text

Extracted automatically from the original. Tables and formatting may not survive; the original document is authoritative.

AGENDA HISTORIC PRESERVATION/ DESIGN REVIEW COMMISSION Members • Chairperson Tim Siebert • Vice Chair Peter Munck • Alderperson Marc Christianson • Barry Calnan • Carol Molepske • Janet Jurgella Finn (Alternate 1) • Dan Kryst (Alternate 2) Date and Time: January 13, 2026 5:00 PM Location: Community Room 933 Michigan Avenue, Stevens Point, WI OR Zoom Teleconferencing Meeting ID: 831 6239 0141 Passcode: 466142 Computer: https://us02web.zoom.us/j/8316 2390141?pwd=hNWMPG5b9NF2 XPbbqM Phone: +1-312-626-6799 (US Chicago) Opening Section: 1. Roll Call Discussion and Possible Action on: 2. Report of the November 13, 2025 meeting of the Historic Preservation / Design Review Commission. 3. A request from Michael More, representing RA Cook & JI Altenburg Cooperative, for a demolition review to raze portions of the building located at 2041 Madison Street (Parcel ID 281240832403709), consistent with Ch. 22.05(2). 4. A request from Michael More, representing RA Cook & JI Altenburg Cooperative, for a design review to construct a building addition on the property located at 2041 Madison Street (Parcel ID 281240832403709), consistent with Ch. 22.05(2). 5. A request from the City of Stevens Point to raze the building located at 1039 Ellis Street (Parcel ID 281240832202053), consistent with Ch. 22.05(2). Closing Section: 6. Adjourn Page 1 of 46 PLEASE TAKE NOTICE that any person who has special needs while attending these meetings or needs agenda materials for these meetings should contact the City Clerk as soon as possible to ensure that a reasonable accommodation can be made. The City Clerk can be reached by telephone at (715) 346-1569 or by mail at 1515 Strongs Avenue, Stevens Point, WI 54481. Maps further defining the above area(s) may be obtained from the City of Stevens Point Department of Community Development, 1515 Strongs Avenue, Stevens Point, WI 54481, or by calling (715) 346-1567, during normal business hours. PLEASE TAKE FURTHER NOTICE that a quorum of the Common Council may be in attendance at this meeting. Page 2 of 46 Page 1 of 3 REPORT OF THE HISTORIC PRESERVATION/DESIGN REVIEW COMMISSION November 13, 2025 – 5:00 PM 933 Michigan Ave, Stevens Point, WI 54481 PRESENT: Chair Siebert, Vice Chair Munck, Commissioner Jurgella Finn, Commissioner Calnan, and Commissioner Kryst EXCUSED: Alderperson Christianson, Commissioner Molepske ALSO PRESENT: Associate Planner / Zoning Administrator Kuhn INDEX: Opening Section: 1. Roll Call Discussion and Possible Action on the Following: 2. Report of the October 23, 2025 meeting of the Historic Preservation / Design Review Commission. 3. A request from Nicole Terrill, representing Elodin Holdings LLC, for a design review to install a structure on the property located at 1220 Briggs Court (Parcel ID 281240832200137), consistent with Ch. 22.02(2). 4. A request from Robert Wilder to install a deck on the building located at 1724 Clark Street (Parcel ID 281240832103612), consistent with Ch. 22.05(2). 5. Overview of Zoning Code Rewrite: • Conservation Districts • City Historic Preservation Plan Closing Section: 6. Adjourn Opening Section: 1. Roll Call Present: Siebert, Munck, Calnan, Jurgella Finn, and Kryst Excused: Christianson, Molepske Discussion and Possible Action on the Following: 2. Report of the October 23, 2025 meeting of the Historic Preservation / Design Review Commission. Motion by Vice Chair Munck, to approve the October 23, 2025 minutes of the Historic Preservation/Design Review Commission; seconded by Commissioner Calnan. Page 3 of 46 Page 2 of 3 Motion carried 5-0. 3. A request from Nicole Terrill, representing Elodin Holdings LLC, for a design review to install a structure on the property located at 1220 Briggs Court (Parcel ID 281240832200137), consistent with Ch. 22.02(2). Nicole Terrell presented a request to install a second sauna structure on the property at 1220 Briggs Court. Associate Planner / Zoning Administrator Kuhn noted that a similar structure had been approved by the Commission years prior. The new unit matches the previously approved design and includes polycarbonate panels utilized to match the surrounding environment and provide passive solar heating. Motion by Commissioner Calnan to approve the request to install a structure on the property located at 1220 Briggs Court; seconded by Commissioner Kryst. Motion carried 5-0 4. A request from Robert Wilder to install a deck on the building located at 1724 Clark Street (Parcel ID 281240832103612), consistent with Ch. 22.05(2). Austin Lamb, who recently purchased the property from Robert Wilder, presented his request for the demolition of an existing deck and the following installation of a new deck on the property located at 1724 Clark Street. The proposal meets existing design standards and zoning requirements. Motion by Vice Chair Munck to approve the request to install a deck on the property located at 1724 Clark Street; seconded by Commissioner Kryst. Motion carried 5-0 5. Overview of Zoning Code Rewrite: • Conservation Districts • City Historic Preservation Plan Alderperson Christianson attended virtually and was present for the Overview of the Zoning Code Rewrite. Associate Planner / Zoning Administrator Kuhn provided an update on the City’s Zoning Code Rewrite and requested Commission feedback on whether to include conservation districts for designated areas identified as historically eligible. Kuhn explained conservation districts regulate major changes and offer lighter restrictions than what a full historic district would require. Commissioners discussed district conditions, potential benefits, and potential concerns of property owners within these proposed districts. Consensus was that no conservation districts should be pursued without conducting public feedback. Closing Section: 6. Adjourn Meeting adjourned at 5:40 PM. A recording of this meeting can be viewed/heard at: https://stevenspoint.com/365/AgendasMinutesVideos Page 4 of 46 Page 3 of 3 Page 5 of 46 Page 1 of 6 Administrative Staff Report Department of Community Development 1515 Strongs Avenue, Stevens Point, WI 54481 Ph: (715) 346-1568 - Fax: (715) 346-1498 Demolition & Design Review 2041 Madison Street January 13, 2026 Applicant(s): • Michael More, representing RA Cook & JI Altenburg Cooperative Staff: • Adam Kuhn, Associate Planner akuhn@stevenspoint.com Parcel Number(s): • 281240832403709 Zone(s): • “M-2” Heavy Industrial Council District: • District 5 – Ald. Birr Lot Information: • Actual Frontage: 429 feet • Effective Depth: 263 feet • Square Footage: 56,628 • Acreage: 1.30 Planned Use: • Community Building Applicable Regulations: • Chapter 22 • Downtown Design Guidelines Request A request from Michael More, representing RA Cook & JI Altenburg Cooperative, for a demolition review to raze portions of the building located at 2041 Madison Street (Parcel ID 281240832403709), consistent with Ch. 22.05(2). A request from Michael More, representing RA Cook & JI Altenburg Cooperative, for a design review to construct a building addition on the property located at 2041 Madison Street (Parcel ID 281240832403709), consistent with Ch. 22.05(2). City Official Design Review / Historic District 1. Local landmark property Staff Recommendation Approve the request for a demolition review to raze portions of the building located at 2041 Madison Street (Parcel ID 281240832403709), subject to the following conditions: 1. A razing permit shall be obtained prior to the start of demolition. Approve the request for a design review to construct a building addition on the property located at 2041 Madison Street (Parcel ID 281240832403709), subject to the following conditions: 1. A landscaping plan shall be submitted to the Designated Agent for review and approval. 2. A building permit shall be obtained prior to the start of construction. Page 6 of 46 Page 2 of 6 Vicinity Map Scope of Work Overview: In 2024, the Common Council designated the subject property as a local landmark, at the request of the property owner. At the time, the intent for the local landmark designation request, in part, was to help facilitate an adaptive reuse project within the existing building. Being designated a local landmark property enables historic building code requirements to be used for interior work, thus adding some flexibility as part of the interior buildout. Enclosed in the agenda packet are interior plans for how the interior of the building is proposed to be used. The proposal includes two multi-activity spaces, a bakery, and a bar within the building. Please note that the bar/seating area identified in the plan set is subject to Plan Commission and Council approval, which is slated for consideration next month. The demolition review requests to raze the loading dock situated on the west elevation of the building. The loading dock consists of cinder block siding material, which is inconsistent with the exterior façade material used for the remainder of the building (i.e., brick). Based on historic photographs, it is apparent that the loading dock was not original to the 1892 construction of the building. The design review requests to construct two additions onto the building. Where the loading dock is proposed to be razed, the applicant seeks to construct a 73 sq ft vestibule addition that will serve as a required means of egress for uses within the building. Second, a 2,800 sq ft addition is proposed on the southeast corner of the building. This addition would serve the proposed bakery use, and would have a partial basement. According to Section 7.4 of the Historic Preservation / Design Review Commission’s Design Guidelines, building demolitions, in whole and in part, along with building additions, are considered a ‘major work’ and requires the review and approval of the Commission. Said requirement is outlined below. Sec. 7.4: Major and Minor Works Page 7 of 46 Page 3 of 6 Sec. 7.4.1 Major Works (HPDRC Approval) a. New construction or additions to primary buildings c. Demolition of any structure The process to obtain a design review from the Commission is identified below. CHAPTER 22: HISTORIC PRESERVATION Division 5.02 Regulation of Construction, Reconstruction, Alteration, and Demolition No owner or person in charge of a historic structure or historic site, or property located within a historic district shall reconstruct, alter, or demolish all or any part of the exterior of such property or construct any improvement upon such designated property or properties or cause or permit any such work to be performed upon such property or demolish such property unless approval has been granted by the commission. Upon the filing of any request for a design review certificate with the commission, the commission shall review the request in accordance with the design guidelines. If the commission determines that the application for a design review certificate and the proposed changes are consistent with the design guidelines, it shall issue the design review certificate. Upon the issuance of such certificate, any other required permits shall be obtained. Guidelines of Review (numbers below pertain to the pertinent guideline standards) ***Other standards within the design guidelines not specifically mentioned below have been reviewed and are met or not applicable pertaining to the proposed building improvement activities. SEC. 6.1.2: Demolition Guidelines 1. Whether the building or structure is of such architectural or historic significance that its demolition would be detrimental to the public interest and contrary to the general welfare of the people of the city or state. Analysis: The building was constructed in 1892 and was designated as a local landmark in 2024. The loading dock was constructed after 1892, albeit the exact year of construction is not known. Findings: The proposed demolition is not detrimental to the public interest and is not contrary to the general welfare. The loading dock is partially shielded from public view off of Madison Street. As the loading dock was built after the original building was constructed, and constructed in a way that is not consistent with the rest of the building, the proposed demolition will better achieve uniformity in architectural cohesiveness. 2. Whether the building or structure, although not itself a historic structure, contributes to the distinctive architectural or historic character of the historic district as a whole, and therefore, should be preserved Loading dock subject to demolition Page 8 of 46 Page 4 of 6 for the benefit of the people of the city or the state. Analysis: The structure is a designated local landmark and is not part of a broader historic district. Findings: The proposed demolition would not diminish the architectural and historic character of the site. The removal of the loading dock would eliminate the exterior appearance of the building as an industrial use, and would better appeal to land uses in surrounding buildings. 4. Whether the building or structure is of such old, unusual or uncommon design, texture, and/or material, that it could be reproduced only with great difficulty and/or expense. Analysis: Cinder block is the exterior material used for the loading dock. Findings: Cinder block is a common façade material, and in this instance is consistent with the building materials used on the remainder of the building. 7. Whether demolition of the building or structure would promote conformance with other criteria as designated in the City of Stevens Point Historic Design guidelines. Analysis: Please see above. The proposed demolition would better meet the exterior wall guidelines as identified in the Commission’s Design Guidelines. Findings: This standard is met. SEC. 5.3: Addition Guidelines 1. Additions should be located to the rear or non- character defining elevation. With historic residential structures, additions should be placed in a manner that they are not clearly seen from the public right-of-way. Landscaping can often be used to minimize the visual impact that additions may have to the historic structure. Analysis: The proposed additions would be located along the side elevations of the buildings. While the addition would not be seen from Madison Street, it would be visible from Monroe Street. Monroe Street terminates into a turnaround at the east side lot line of the subject Proposed Site Plan Page 9 of 46 Page 5 of 6 property. As Monroe Street dead ends at the subject property, along with being adjacent to the Canadian National railyard, I believe that the landscape screening suggestion should be waived in this instance. Findings: This standard is met. 2. New additions should not remove, damage, or obscure character-defining architectural features. Analysis: The proposed vestibule addition would reintroduce more of the original exterior wall that is currently covered by the loading dock. Both additions would utilize the same roofing material as the rest of the building, while EIFS siding will be used. The lower portion of both additions will utilize a concrete veneer that detailed with a brick aesthetic to better match the texture and definition as the rest of the exterior walls on the building. Findings: This standard is met. 3. Additions should be compatible in materials, design, roof form, and proportion to the main structure. However, new additions should be constructed at a scale smaller than the historic structure so as not to overpower the existing historic building. Analysis: Please see item #2 above for details on the proposed siding and roof materials for the addition. Both additions are of small scale that would not overpower the reminder of the building that is original. Findings: This standard is met. 4. Additions, like new construction, are representative of the time in which they are built. Therefore, contemporary designs are permitted, but should always be compatible with the existing historic structure. Analysis: Both additions would utilize the same roofing material as the rest of the building, while EIFS siding will be used. The lower portion of both additions will utilize a concrete veneer that detailed with a brick aesthetic to better match the texture and definition as the rest of the exterior walls on the building. Findings: The concrete base that is stamped to take shape comparable to brick would best match the siding pattern used on the remainder of the building, while trying not to mimic it by utilizing a different façade material. 5. An addition should never mimic or recreate the architecture of the primary historic structure. Analysis: Please see item #4 above. Findings: This standard is met. 6. Additions to historic structures should be clearly identifiable as such. Additions should be set back and constructed at a smaller scale than the original building. Architectural details should complement the main structure but should be clearly differentiated. Analysis: As the subject property abuts streets along the north and south lot lines, the location of the proposed additions are intentionally centered in the middle of the lot to make it best be shown at a small scale from a public right-of-way. Both additions are relatively small in size, particularly in relation to the remainder of the building. Findings: This standard is met. Sec. 4.3.1: Landscaping Guidelines 1. Parking lots, driveways, and sidewalks shall comply with any ordinance requirements for size and landscaping elements as well as site grading. Page 10 of 46 Page 6 of 6 Analysis: A parking lot is proposed that would be situated to the west of the existing building. The proposed parking lot meets minimum design standards identified in the City’s Zoning Code (i.e., stall dimensions, aisle widths, pavement setbacks, ADA accessibility, etc.). A landscaping plan has not been submitted, but is required as part of the pending conditional use permit request. Findings: As a condition of approval, a landscaping plan shall be submitted for review and approval. Said plan shall meet landscaping guidelines as identified in Section 4.3.1 of the Commission’s Design Guidelines, as well as the Zoning Code. Page 11 of 46 Page 12 of 46 Page 13 of 46 Page 14 of 46 PROPERTY LINEMONROE STREETLOCATED AT 2041 MADISONSTREET, CITY OF ST. POINT,PORTAGE COUNTY,WISCONSIN PROPERTY LINE EXISTINGDRIVEWAY EXISTING DRIVEWAY EXISTING DRIVEWAY NEW FENCEEXISTING BUILDING STORAGE(S1,S2), FACTORY (F1/F2), OFFICE(B), MERCANTILE (M), ASSEMBLY(A2/A3), 1 STORY, 11,457 SQ. FT.,TYPE VB. A COMPLETE SPRINKLERSYSTEM PER NFPA 13 SHALL BEADDED TO EXISTING BUILDING. PROPOSED BAKERY ADDITION (F1),1 STORY, W/ PARTIAL BASEMENT,TYPE VB, 2,800 SQ. FT. 40'-0"32'-1034"70'-0" 43'-5116" HANDICAP ACCESSIBLEPARKING SPOTS W/ SIGN PROPOSED VESTABULE ADDITION, 1STORY,, TYPE VB, 73 SQ. FT. 4 6 135 DRAWN BY:CHECKED BY: 547 HEWETT ST.P.O. BOX 189NEILLSVILLE, WI 54456PHONE: 715.743.2240FAX: 715.743.4469WWW.RATSCHENGINEERING.COMPROJECT NAME:PROJECT DESCRIPTION:PROJECT ADDRESS: SHEET:SHEET DISCRIPTION: DISCLAIMER:ALTHOUGH DILIGENT EFFORTS HAVE BEEN MADE IN THE PREPARATION AND CHECKING OF THESE PLANS FOR ACCURACY, ALL CONTRACTORS SHALL CHECK, VERIFY AND BE RESPONSIBLE FOR ALL DETAILS AND DIMENSIONS. ALL CONTRACTORS SHALL EXAMINE THE SITE AND EXISTING CONDITIONS OF THE PROPOSED WORK. ALL CONTRACTORS SHALL REVIEW ALL PLAN PAGES FOR WORK IN THEIR CONTRACT. ALL WORK ON THIS PROJECT IS TO BE GOVERNED BY THE LATEST EDITION OF THE CODESAPPLICABLE TO THE LOCAL ORDINANCES. ALL WORK SHALL BE PERFORMED IN ACCORDANCE WITH ACCEPTED BUILDING PRACTICES AND INDUSTRY STANDARDS. VERIFY AND USE ONLY WRITTEN DIMENSIONS. DO NOT SCALE OR MEASURE DIMENSIONS DIRECTLY FROM PRINT. ALL CONTRACTORS MUST BE RESPONSIBLE FOR ALL AND ANY DAMAGE TO "EXISTING" STRUCTURE CAUSED EITHER DIRECTLY OR INDIRECTLY BY THEIR TRADES. VERIFY ANY UNCERTAIN ITEMS WITH OWNER, BUILDER, AND/ORENGINEER. ENGINEER WILL NOT BE RESPONSIBLE FOR EXISTING OR PREEXISTING SOIL OR STRUCTURAL CONDITIONS. THE ENGINEER WILL NOT BE RESPONSIBLE FOR CONSTRUCTION MEANS, METHODS, TECHNIQUES, SEQUENCES, OR PROCEDURES, OR FOR SAFETY PRECAUTIONS AND PROGRAMS IN CONNECTION WITH THE WORK AND HE SHALL NOT BE RESPONSIBLE FOR THE CONTRACTOR'S FAILURE TO CARRY OUT THE WORK IN ACCORDANCE WITH THE CONTRACT DOCUMENTS. CONTRACTOR SHALL REVIEWALL SHOP DRAWINGS PRIOR TO SUBMITTAL TO ENGINEER. PLAN SET:PRELIMINARYSCALE:DATE:REVISION: SHEET SIZE:ARCH D 36X24ALTENBURG - CENTER CITY MARKETPROPOSED MERCANTILE/ASSEMBLY ADDITION/ALTERATION2041 MADISON STREET STEVENS POINT, WISCONSIN 54481 10/27/2025 T1.1 SLSSITE PLAN & DESIGN DATAAS NOTED--- ------------------------ 1SITE PLANSCALE: 1"=20'-0" CODE SUMMARYOCCUPANCYA2A3BF1F2MS1S2 TYPE OF CONSTRUCTIONVBVBVBVBVBVBVBVB SPRINKLERNFPA 13NFPA 13NFPA 13NFPA 13NFPA 13NFPA 13NFPA 13NFPA 13 FIRE ALARM SYSTEMNFPA 72NFPA 72NFPA 72NFPA 72NFPA 72NFPA 72NFPA 72NFPA 72 ALLOWABLE HEIGHT60 FT60 FT60 FT60 FT60 FT60 FT60 FT60 FT ALLOWABLE STORIES22323223 ALLOWABLE BLDG AREA PER TABLE 506.224,000 SQ. FT.24,000 SQ. FT.36,000 SQ. FT.34,000 SQ. FT.52,000 SQ. FT.36,000 SQ. FT.36,000 SQ. FT.54,000 SQ. FT.COMMON PATH OF EGRESS WITH SPRINKLERS75 FT75 FT100 FT100 FT100 FT75 FT100 FT100 FT EXIT DISTANCE WITH SPRINKLERS250 FT250 FT300 FT250 FT400 FT250 FT250 FT400 FT FLOOR AREA ALLOWANCE155010010010060500500 NUMBER OF PEOPLEREQUIRED TOILET1 PER 75M - 1 PER 150W - 1 PER 7525 - 1ST 50 THEN1 PER 50100100500100100 REQUIRED LAVATORY1 PER 2001 PER 20040 - 1ST 80 THEN1 PER 80100100750100100 REQUIRED DRINKING FOUNTAIN1 PER 5001000100400400100010001000 REQUIRED SERVICE SINK11111111 REQUIRED TOILET FIXTURESOCCUPANCYOCCUPANTLOADMENTOILETWOMENTOILETLAVATORYDRINKINGFOUNTAINSERVICESINK A22701.801.801.350.541 A3660.220.440.330.071 B30.060.060.040.031 F1/F2140.070.070.140.041 M590.120.120.080.061 S1/S240.020.020.040.011 TOTAL REQUIRED2.292.511.980.751 TOTAL PROVIDED3.003.006.002.001 DESIGN DATADESIGN CODE: 2018 WISCONSIN COMMERCIAL BUILDING CODE (2015 IBC)BUILDING CATEGORY: IIEXPOSURE CATEGORY: BDESIGN ROOF SNOW LOADSGROUND SNOW, Pg50 PSFIMPORTANCE FACTOR, Is1.0 EXPOSURE FACTOR, Ce1.0 FLAT ROOF/SLOPE FACTOR, Cs1.0 THERMAL FACTOR, Ct1.1 ROOF SNOW LOAD, Ps38.5 PSFUNBALANCED PER SPS 362.16080.0 PSFROOF LOAD LLDLCLTL TOP CHORD38.57348.5 PSFBOTTOM CHORD010616.0 PSF58.5 PSFCL INCLUDES: 3 PSF FOR SPRINKLERS & 3 PSF FOR COLLATERALSEE ROOF FRAMING PLAN FOR DRIFT LOADLLDLCLTL FLOOR LOAD100105.56211.5 PSFCL INCLUDES: 3 PSF FOR SPRINKLERS & 3 PSF FOR COLLATERALDESIGN WIND LOADSBASIC WIND SPEED115 MPHEXPOSURE CATEGORYBENCLOSEDq/h20.14 PSFSEISMIC DESIGN LOADSEISMIC IMPORTANCE FACTOR1.0SS0.052S10.033SDS0.056SD10.053SITE CLASSIFICATIOND SEISMIC DESIGN CATEGORYA DESIGN STRESSCONCRETE - F'c3,500 PSIREINFORCING BARS - GRADE 60 - fy3,000 PSFSOIL BEARING PRESSURE2,000 PSF INDEXT1.1SITE PLAN & DESIGN DATAG1.1CODE PAGED1.1DEMOLITION PLANA1.1FIRST FLOOR PLANA1.2MEZZANINE & BASEMENT FLOOR PLANSA1.3ENLARGED BAKERY FLOOR PLANA2.1ELEVATIONSA2.2CROSS SECTIONSS1.1FOUNDATION & ROOF FRAMING PLANS OCCUPANCY SCHEDULEROOM NUMBEROCCUPANCY CLASSIFICATIONOCCUPANCY LOAD102M56 103M3 106A314 107A329 118A276 120F114 121B1 122B1 128A244 129A2150001S14 201A323 202B1 Page 15 of 46 RATED FIRE EXTINGUISHERCABINET - SEE SPECS.WOOD STUDS EA.SIDE AS SHOWNWALL TYPEPER PLANSNOTE: SEE FLOOR PLANS FOR LOCATIONSFIRE EXTINGUISHER CABINET FIRE EXTINGUISHER CABINET IN RATED WALL RATED FIRE EXTINGUISHERCABINET - SEE SPECS.WOOD STUDS EA.SIDE AS SHOWNWALL TYPEPER PLANSNOTE: DESIGN AFTER GA FILE NO. 1330SEE FLOOR PLANS FOR LOCATIONS (4) LAYERS 58"TYPE 'X' GYP. BD. FIRE EXTINGUISHER CABINETNTS 60"36"24"12"36"12"Ø5'-0"T- SHAPED TURNING SPACETURNING RADIUS 30"48"60"60"16"-18"WATERCLOSETLOCATIONCLEAR FLOOR SPACE TURNING SPACE:CLEAR FLOOR SPACE: WATER CLOSET CLEARANCEACCESSIBILITY SYMBOLSNTS 60" MIN.(a) FRONT APPROACH, PULL SIDE18" MIN. 48" MIN.12" MIN.**IF BOTH CLOSER AND LATCHARE PROVIDED ACCESSIBILITY DIAGRAMSNTS 60" MIN.(c) HINGE APPROACH, PULL SIDE36" MIN.54" MIN.(c) HINGE APPROACH, PULL SIDE42" MIN.(b) FRONT APPROACH, PUSH SIDE12" MIN.**IF BOTH CLOSER AND LATCHARE PROVIDED**48" MIN. IF BOTH CLOSER ANDLATCH PROVIDED (e) HINGE APPROACH, PUSH SIDE48" MIN.**22" MIN.*54" MIN. IF CLOSER ISPROVIDED (f) LATCH APPROACH, PULL SIDE48" MIN.*24" MIN.24" MIN.*48" MIN. IF CLOSER ISPROVIDED (g) LATCH APPROACH, PUSH SIDE42" MIN.* 48" MAX.15" MIN.48"34" MAX.10" MAX.48"34" MAX.10"-24"MAX.(a) FORWARD AND SIDEREACH LIMIT(b) SIDE REACH LIMIT(c) SIDE REACH LIMITREACH DIMENSIONS OVER AN OBSTRUCTION:48" MAX.0"-24"MAX.44" MAX.20"-25"MAX.(a) FORWARD REACH LIMIT(b) FORWARD REACH LIMITLIMITS OF PROTRUDINGOBJECTS REDUCED VERTICAL CLEARANCE 80" MIN.4" MAX.27" MIN.80" MIN.27" MAX. 60" MIN.FLOOR SPACE18"℄REAR WALLSIDE WALL 56" MIN.FLOOR SPACEACCESSIBLE WATERCLOSET PLANACCESSIBLE WATERCLOSET SIDE WALLACCESSIBLE WATERCLOSET REAR WALLACCESSIBLEURINALSTANDARDURINALFLOORMOUNTEDURINALLAVATORYLAVATORYDRINKINGFOUNTAINADADRINKINGFOUNTAINADADRINKINGFOUNTAINHIGH LOWDRINKINGFOUNTAINDRINKINGFOUNTAINCHILD 41"54" MIN.12"MAX.42" MIN.17"-19"33"-36"T.O. GRAB BAR39"-41"18"MIN. 33"-36"T.O. GRAB BAR6" MAX.12"MIN.24"MIN.36" MIN.PROVIDE FLUSHHANDLE ON THEAPPROACH SIDE OFWATER CLOSET℄1312"MIN.17" MAX.17"MAX.44" MAX.24"44" MAX. 15"MIN.MIRROR34" MAX.40" MAX.TO REFLECTIVESURFACE34" MAX.27" MIN.8" MIN.6" MAX.11" MIN.9" MIN.40" MAX.TO REFLECTIVESURFACE17"-25"DEPTH 27" MIN.15" MIN.5" MAX.9" MIN.6" MAX.8" MIN.36" MAX.SPOUT OUTLET36" MAX.SPOUT OUTLET36" MAX.SPOUT OUTLETADA WATERBOTTLE FILLERIF APPLICABLE 38"-43"SPOUT OUTLET38"-43"SPOUT OUTLET30"SPOUT OUTLET TOILET ACCESSORIES15" MIN.1 12" MIN.SANITARY NAPKINDISPOSAL IF APPLICABLETOILET TISSUE DISPENSERTOILET SEAT COVERIF APPLICABLE15" MIN.1 12" MIN.7"-9"1 12" MIN.℄24" MIN. BABY CHANGESTATIONSOAPDISPENSERACCESSIBLEHAND DRYERPAPER TOWELDISPENSERPAPER TOWELDISPENSERAND DISPOSALSANITARYNAPKINDISPOSAL 34" MAX.T.O. WORKSURFACE27" MIN.48" MAX. T.O. OPERABLEPORTION44"-48" T.O. OPERABLEPORTION44"-48" T.O. OPERABLEPORTION44"-48" T.O. OPERABLEPORTIONSEE TABLE 603.6ON THIS SHEET15" MIN.48" MAX. SIGNAGE18" MIN.CLEARSPACE9"MIN.18" MIN.℄9"MIN.48"-60"LOCATE SIGN ALONGLATCH SIDE OF DOORPRO72"48" MAX. T.O. CONTROLHANDLEFIREEXTINGUISHERCABINETSTANDARDROBE HOOKACCESSIBLEROBE HOOKACCESSIBLETOWEL BARMOP CLIPSTRIPACCESSIBLECOATRACK/SHELFCOATRACK/SHELF 60"44"-48"44"-48"72" 44"-48"66" ACCESSIBLEBATHTUB WITHREMOVABLE SEATCONTROL WALLBACK WALLHEAD WALLCONTROLAREA℄4" MAX.8"-10"33"-36"3"-6"18" MIN.33"-36"3"-6"18" MIN.8"-10"33"-36"8"-10"33"-36"4" MAX.12" MIN.33"-36" LENGTH OF TUBCLEAR FLOORSPACE BACK WALLCONTROL WALL HEAD WALL30" CLEARFLOOR SPACE4" MAX.12" MIN.ADA COMPLIANTREMOVABLE IN-TUB SEAT24" MAX.24" MIN.12" MAX.24" MIN.6" MIN. ACCESSIBLETRANSFER-TYPESHOWERBACK WALLSEAT WALLCONTROL WALL BACK WALLCONTROL WALL SEAT WALL17"-19"17"-19"18"MIN.33"-36"3"-6"18" MIN.33"-36"3"-6"18" MIN.18"℄15" MAX.4" MAX.CONTROL AREAADJUSTABLE SHOWERW/ 59" MIN. HOSE38" MIN.48" MAX. 48" CLEARFLOOR SPACE36" CLEARFLOORSPACE4" MAX.14"-15"18"36"3" MAX.15"-16"212" MAX.36"112" MAX. 33"-36"3"-6"18" MIN.33"-36"3"-6"18" MIN.6" MAX.SEAT WALLCONTROL WALLSIDE WALL 17"-19"38" MIN.48" MAX.ALIGN GRAB BARTO EDGE OF SEATCONTROL AREA16" MIN.27" MAX.6" MAX. ADJUSTABLE SHOWERW/ 59" MIN. HOSE ACCESSIBLEROLL-IN-TYPESHOWER 17"-19" CONTROL WALL SEAT WALL SIDE WALL60" CLEARFLOOR SPACE30" CLEARFLOORSPACE 60" MIN.24" MIN.6" MAX.6" MAX.30" MIN.112" MAX.15"-16"212" MAX. 84"78"3"℄SHOWERCURTAIN ROD CONTROL WALLBACK WALLALTERNATE ACCESSIBLEROLL-IN-TYPE SHOWERSTANDARDSHOWER HEAD 33"-36"33"-36"6" MAX.6" MAX. 17"-19"38" MIN.48" MAX.16" MIN.27" MAX.CONTROL AREAADJUSTABLE SHOWERW/ 59" MIN. HOSE BACK WALL CONTROL WALL SIDE WALL6" MAX.6" MAX.36"36" MIN.24"-36"60" MIN.6" MAX.15"-16"112"MAX.212" MAX. STANDARD MOUNTING HEIGHTSNTS TABLE 603.6MAXIMUM REACH DEPTH AND HEIGHTMAX. REACH DEPTHMAX. REACH DEPTH2 INCHES46 INCHES5 INCHES42 INCHES6 INCHES42 INCHESNOTE:1. THESE DRAWINGS CONTAIN STANDARD SYMBOLS AND DETAILS. NOT ALL ITEMS APPEAR IN THESE DRAWINGS.2. CONTRACTOR SHALL PROVIDE FIRE TREATED WOOD BLOCKING IN GYPSUM BOARD PARTITIONS FOR MOUNTING OF WALL ATTACHED ITEMS INCLUDING, BUT NOT LIMITED TO; GRAB BARS, CABINETS/SHELVING, TOILET PARTITIONS, ACCESSORIES AND DOOR BUMPER STOPS.3. STANDARD MOUNTING HEIGHTS APPLY TO DRAWINGS UNLESS INDICATED OTHERWISE.DRAWN BY:CHECKED BY: 547 HEWETT ST.P.O. BOX 189NEILLSVILLE, WI 54456PHONE: 715.743.2240FAX: 715.743.4469WWW.RATSCHENGINEERING.COMPROJECT NAME:PROJECT DESCRIPTION:PROJECT ADDRESS: SHEET:SHEET DISCRIPTION: DISCLAIMER:ALTHOUGH DILIGENT EFFORTS HAVE BEEN MADE IN THE PREPARATION AND CHECKING OF THESE PLANS FOR ACCURACY, ALL CONTRACTORS SHALL CHECK, VERIFY AND BE RESPONSIBLE FOR ALL DETAILS AND DIMENSIONS. ALL CONTRACTORS SHALL EXAMINE THE SITE AND EXISTING CONDITIONS OF THE PROPOSED WORK. ALL CONTRACTORS SHALL REVIEW ALL PLAN PAGES FOR WORK IN THEIR CONTRACT. ALL WORK ON THIS PROJECT IS TO BE GOVERNED BY THE LATEST EDITION OF THE CODESAPPLICABLE TO THE LOCAL ORDINANCES. ALL WORK SHALL BE PERFORMED IN ACCORDANCE WITH ACCEPTED BUILDING PRACTICES AND INDUSTRY STANDARDS. VERIFY AND USE ONLY WRITTEN DIMENSIONS. DO NOT SCALE OR MEASURE DIMENSIONS DIRECTLY FROM PRINT. ALL CONTRACTORS MUST BE RESPONSIBLE FOR ALL AND ANY DAMAGE TO "EXISTING" STRUCTURE CAUSED EITHER DIRECTLY OR INDIRECTLY BY THEIR TRADES. VERIFY ANY UNCERTAIN ITEMS WITH OWNER, BUILDER, AND/ORENGINEER. ENGINEER WILL NOT BE RESPONSIBLE FOR EXISTING OR PREEXISTING SOIL OR STRUCTURAL CONDITIONS. THE ENGINEER WILL NOT BE RESPONSIBLE FOR CONSTRUCTION MEANS, METHODS, TECHNIQUES, SEQUENCES, OR PROCEDURES, OR FOR SAFETY PRECAUTIONS AND PROGRAMS IN CONNECTION WITH THE WORK AND HE SHALL NOT BE RESPONSIBLE FOR THE CONTRACTOR'S FAILURE TO CARRY OUT THE WORK IN ACCORDANCE WITH THE CONTRACT DOCUMENTS. CONTRACTOR SHALL REVIEWALL SHOP DRAWINGS PRIOR TO SUBMITTAL TO ENGINEER. PLAN SET:PRELIMINARYSCALE:DATE:REVISION: SHEET SIZE:ARCH D 36X24ALTENBURG - CENTER CITY MARKETPROPOSED MERCANTILE/ASSEMBLY ADDITION/ALTERATION2041 MADISON STREET STEVENS POINT, WISCONSIN 54481 10/27/2025 G1.1 HGBCODE PAGEAS NOTED--- ------------------------ Page 16 of 46 REMOVELOADINGDOCK REMOVEWALLREMOVESTAIRSREMOVEWALL TOHEIGHT OFEXTERIORWALLS REMOVE ALLINTERIORWALLS3'-4"REMOVE DOOR ANDWIDEN OPENING REMOVE ALLINTERIORWALLSREMOVE ALLINTERIORWALLS 7'-1112" 10'-3"7'-212"3'-4"23'-212" 12'-1012" 68'-10"6'-4"REMOVE WINDOWAND WALL FORDOOR OPENING 28'-8"6'-4"REMOVEWALLWHEREFORMERDOORWAYWAS FORNEWDOORWAY 2'-6"12'-712"REMOVE2'-6"X3'-0"OPENING34" FROMFLOORREMOVEWINDOWAND WALLBELOWREMOVEWALL FORWALKWAYREMOVEWINDOWAND WALLBELOW8'-912" 48'-1114" 3'-4" 5'-0"4'-0" 1FLOOR PLANSCALE: 1/8"=1'-0"DRAWN BY:CHECKED BY: 547 HEWETT ST.P.O. BOX 189NEILLSVILLE, WI 54456PHONE: 715.743.2240FAX: 715.743.4469WWW.RATSCHENGINEERING.COMPROJECT NAME:PROJECT DESCRIPTION:PROJECT ADDRESS: SHEET:SHEET DISCRIPTION: DISCLAIMER:ALTHOUGH DILIGENT EFFORTS HAVE BEEN MADE IN THE PREPARATION AND CHECKING OF THESE PLANS FOR ACCURACY, ALL CONTRACTORS SHALL CHECK, VERIFY AND BE RESPONSIBLE FOR ALL DETAILS AND DIMENSIONS. ALL CONTRACTORS SHALL EXAMINE THE SITE AND EXISTING CONDITIONS OF THE PROPOSED WORK. ALL CONTRACTORS SHALL REVIEW ALL PLAN PAGES FOR WORK IN THEIR CONTRACT. ALL WORK ON THIS PROJECT IS TO BE GOVERNED BY THE LATEST EDITION OF THE CODESAPPLICABLE TO THE LOCAL ORDINANCES. ALL WORK SHALL BE PERFORMED IN ACCORDANCE WITH ACCEPTED BUILDING PRACTICES AND INDUSTRY STANDARDS. VERIFY AND USE ONLY WRITTEN DIMENSIONS. DO NOT SCALE OR MEASURE DIMENSIONS DIRECTLY FROM PRINT. ALL CONTRACTORS MUST BE RESPONSIBLE FOR ALL AND ANY DAMAGE TO "EXISTING" STRUCTURE CAUSED EITHER DIRECTLY OR INDIRECTLY BY THEIR TRADES. VERIFY ANY UNCERTAIN ITEMS WITH OWNER, BUILDER, AND/ORENGINEER. ENGINEER WILL NOT BE RESPONSIBLE FOR EXISTING OR PREEXISTING SOIL OR STRUCTURAL CONDITIONS. THE ENGINEER WILL NOT BE RESPONSIBLE FOR CONSTRUCTION MEANS, METHODS, TECHNIQUES, SEQUENCES, OR PROCEDURES, OR FOR SAFETY PRECAUTIONS AND PROGRAMS IN CONNECTION WITH THE WORK AND HE SHALL NOT BE RESPONSIBLE FOR THE CONTRACTOR'S FAILURE TO CARRY OUT THE WORK IN ACCORDANCE WITH THE CONTRACT DOCUMENTS. CONTRACTOR SHALL REVIEWALL SHOP DRAWINGS PRIOR TO SUBMITTAL TO ENGINEER. PLAN SET:PRELIMINARYSCALE:DATE:REVISION: SHEET SIZE:ARCH D 36X24ALTENBURG - CENTER CITY MARKETPROPOSED MERCANTILE/ASSEMBLY ADDITION/ALTERATION2041 MADISON STREET STEVENS POINT, WISCONSIN 54481 10/27/2025 D1.1 SLSDEMOLITION PLANAS NOTED--- ------------------------ Page 17 of 46 40'-0" 70'-0" 150 PEOPLE BAKERYCOUNTER BEVERAGES CHECK OUT/INFORMATIONMERCANTILE/SEATING118 VEST119 MERCANTILE102 BAKERY120 MULIT-ACTIVITYSPACE106HALL108UTLY111UNISEX109 INDEPENDENTMERCANTILE103 VEST101UNISEX105 HALL104OFFICE121 ELEC125 MULIT-ACTIVITYSPACE107 UNISEX1106'-6"312"5'-1"312"6'-6"312"4'-6"312"7'-1112" 7'-8"312" 13'-512"6'-912"8'-8"8'-8" 5'-0"312"9'-0" UTLY112UNISEX113UNISEX114UNISEX115 512"40'-0"15'-812"512"312" 11'-0" 67'-912" 8'-8"8'-5" 12'-0"12'-0"12'-0"4'-7"512"6'-6"6'-6"512"6'-6"312" 312"11'-10"30'-9" 12'-0"12'-0"12'-2"15'-10" 10'-0" 10'-0" 125.1 118.1119.1 112.1113.1114.1115.1102.4 102.3102.2 106.1 107.2111.1109.1110.1108.1106.3 106.2102.1101.1103.1 118.3118.2 105.1107.1 120.1 7'-1112" 12'-0" STAIR126 7'-014"9"7'-614" AAA A B B B B B B BBB B D CCCC 8'-612"312"8'-5"312"6'-0"11'-812" AA A DISH DROPOFFFDISH DROPOFF OPENING OPTION 2DUMBWAITER OPTION 1DUMBWAITER6'-0" WALL6'-0" WALL6'-0" TALLWALL 5'-0"312"11'-5"312" COOLROOM116116.1STORAGE117 118.4OFFICE12216'-0"FREEZER124COOLER123 4'-0" WALL4'-0" WALL4'-0" WALL8'-0" WALL B BB E NEW FENCE PATCH WALL TO MATCHEXISTING WALL PATCH WALL TO MATCHEXISTING WALLPATCH WALLTO MATCHEXISTINGWALL PATCH WALL TO MATCHEXISTING WALLPATCH WALL TO MATCHEXISTING WALLPATCH WALL TO MATCHEXISTING WALL96'-0" 10'-0" GATES TO HAVEPANIC HARDWAREGATES TO HAVEPANIC HARDWARE ROOM 103 SHALL HAVEACCESS TO RESTROOMS LULA126 40'-0" VERIFY NON-COMBUSTIBLEMATERIAL BEHIND HOOD 120.1121.1 15'-512" 312"5'-0"312"3'-6"18'-312"CLOSET127127.1 34'-212" OUTDOORSEATING129 56 PEOPLE 48 PEOPLEBAR /SEATING12822 PEOPLE20 PEOPLE 1 PEOPLE1 PEOPLE 14 PEOPLE 14 PEOPLE29 PEOPLE DOWN18R @ 6.44"17T @11" VERFIY SIZE OFLULA SHAFTWITH ELEVATORCOMPANY 1FIRST FLOOR PLANSCALE: 1/8"=1'-0" DRAWN BY:CHECKED BY: 547 HEWETT ST.P.O. BOX 189NEILLSVILLE, WI 54456PHONE: 715.743.2240FAX: 715.743.4469WWW.RATSCHENGINEERING.COMPROJECT NAME:PROJECT DESCRIPTION:PROJECT ADDRESS: SHEET:SHEET DISCRIPTION: DISCLAIMER:ALTHOUGH DILIGENT EFFORTS HAVE BEEN MADE IN THE PREPARATION AND CHECKING OF THESE PLANS FOR ACCURACY, ALL CONTRACTORS SHALL CHECK, VERIFY AND BE RESPONSIBLE FOR ALL DETAILS AND DIMENSIONS. ALL CONTRACTORS SHALL EXAMINE THE SITE AND EXISTING CONDITIONS OF THE PROPOSED WORK. ALL CONTRACTORS SHALL REVIEW ALL PLAN PAGES FOR WORK IN THEIR CONTRACT. ALL WORK ON THIS PROJECT IS TO BE GOVERNED BY THE LATEST EDITION OF THE CODESAPPLICABLE TO THE LOCAL ORDINANCES. ALL WORK SHALL BE PERFORMED IN ACCORDANCE WITH ACCEPTED BUILDING PRACTICES AND INDUSTRY STANDARDS. VERIFY AND USE ONLY WRITTEN DIMENSIONS. DO NOT SCALE OR MEASURE DIMENSIONS DIRECTLY FROM PRINT. ALL CONTRACTORS MUST BE RESPONSIBLE FOR ALL AND ANY DAMAGE TO "EXISTING" STRUCTURE CAUSED EITHER DIRECTLY OR INDIRECTLY BY THEIR TRADES. VERIFY ANY UNCERTAIN ITEMS WITH OWNER, BUILDER, AND/ORENGINEER. ENGINEER WILL NOT BE RESPONSIBLE FOR EXISTING OR PREEXISTING SOIL OR STRUCTURAL CONDITIONS. THE ENGINEER WILL NOT BE RESPONSIBLE FOR CONSTRUCTION MEANS, METHODS, TECHNIQUES, SEQUENCES, OR PROCEDURES, OR FOR SAFETY PRECAUTIONS AND PROGRAMS IN CONNECTION WITH THE WORK AND HE SHALL NOT BE RESPONSIBLE FOR THE CONTRACTOR'S FAILURE TO CARRY OUT THE WORK IN ACCORDANCE WITH THE CONTRACT DOCUMENTS. CONTRACTOR SHALL REVIEWALL SHOP DRAWINGS PRIOR TO SUBMITTAL TO ENGINEER. PLAN SET:PRELIMINARYSCALE:DATE:REVISION: SHEET SIZE:ARCH D 36X24ALTENBURG - CENTER CITY MARKETPROPOSED MERCANTILE/ASSEMBLY ADDITION/ALTERATION2041 MADISON STREET STEVENS POINT, WISCONSIN 54481 10/27/2025 A1.1 SLSFIRST FLOOR PLANAS NOTED--- ------------------------ ROOM FINISH SCHEDULEROOM NUMBERROOM NAMEFLOORBASEWALLSCEILINGHEIGHTNOTES 101VESTEXISTING SEALED CONCRETEVINYLPTD GYP BDPTD GYP BD9'-0" 102MERCANTILEEXISTING SEALED CONCRETEVINYLEXISTING BRICK/NEW PTD GYP BDEXISTINGVARIES 103INDEPENDENT MERCANTILEEXISTING SEALED CONCRETEVINYLEXISTINGEXISTING- 104HALLEXISTING SEALED CONCRETEVINYLPTD GYP BDSUSPENDED9'-0" 105UNISEXEXISTING SEALED CONCRETEVINYLEXISTING BRICK/NEW PTD GYP BDEXISTING9'-0" 106MULTI-ACTIVITY SPACEWOOD FLOORVINYLEXISTING BRICK/NEW PTD GYP BDEXISTING- 107MULTI-ACTIVITY SPACEEXISTING SEALED CONCRETEVINYLEXISTING BRICK/NEW PTD GYP BDPTD GYP BD- 108HALLEXISTING SEALED CONCRETEVINYLPTD GYP BDPTD GYP BD9'-0" 109UNISEXEXISTING SEALED CONCRETEVINYLPTD MR SRPTD MR SR9'-0" 110UNISEXEXISTING SEALED CONCRETEVINYLPTD MR SRPTD MR SR9'-0" 111UTLYEXISTING SEALED CONCRETEVINYLPTD PLYWOODPTD PLYWOOD9'-0" 112UTLYEXISTING SEALED CONCRETEVINYLPTD PLYWOODPTD PLYWOOD9'-0" 113UNISEXEXISTING SEALED CONCRETEVINYLPTD MR SRPTD MR SR9'-0" 114UNISEXEXISTING SEALED CONCRETEVINYLPTD MR SRPTD MR SR9'-0" 115UNISEXEXISTING SEALED CONCRETEVINYLPTD MR SRPTD MR SR9'-0" 116COOL ROOM117STORAGESEALED CONCRETEVINYLPTD MR SRSUSP VINYL SR9'-0" 118MERCANTILE/SEATINGEXISTING SEALED CONCRETEVINYLEXISTING BRICKEXISTINGVARIES 119VESTSEALED CONCRETEVINYLPTD GYP BDPTD GYP BD9'-0" 120BAKERYSEALED CONCRETEVINYLFRP OVER PLYWOODSUSP VINYL SR9'-0" 121OFFICESEALED CONCRETEVINYLFRP OVER PLYWOODSUSP VINYL SR9'-0" 122BAKERYSEALED CONCRETEVINYLFRP OVER PLYWOODSUSP VINYL SR9'-0" 123LDRYSEALED CONCRETEVINYLPTD MR SRSUSP VINYL SR9'-0" 124UNISEXSEALED CONCRETEVINYLPTD MR SRSUSP VINYL SR9'-0" 125ELECSEALED CONCRETEVINYLPTD PLYWOODPTD PLYWOOD13'-412" 126LULASEALED CONCRETENONEPTD PLYWOODPTD PLYWOOD- 127CLOSETSEALED CONCRETEVINYLPTD GYP BDPTD GYP BD9'-0" WINDOW SCHEDULEWINDOW TAGWINDOW SIZEDESCRIPTIONNOTESA4'-0"X1'-6"NEW FIXED VINYL WINDOW W/ SILL MOUNTED AT 7'-0"B3'-4"X8'-0"EXISTING WINDOWC8'-2"X1'-4"EXISTING WINDOWD4'-0"X4'-8"EXISTING WINDOWE3'-4"X5'-4"EXISTING WINDOWF6'-4"X8'-0"NEW STOREFRONT WINDOWVERIFY SIZE DOOR SCHEDULEDOORNUMBERDOOR SIZEDESCRIPTIONHARDWARENOTES101.1(2) 3'-0"X7'-0"NEW DOUBLE ALUMINUM STOREFRONT DOOR W/ CLOSERPANIC102.1(2) 3'-0"X7'-0"NEW DOUBLE ALUMINUM STOREFRONT DOOR W/ CLOSERPANIC102.2(2) 3'-0"X7'-0"NEW INSULATED STEEL DOOR W/ CLOSERSTANDARD EXIT102.33'-4"X7'-0"NEW DOUBLE ALUMINUM STOREFRONT DOOR W/ CLOSERSTANDARD EXIT102.410'-0"X11'-0"EXISTING INSULATED OVERHEAD DOOROPERATOR102.53'-4"X7'-0"EXISTING INSULATED STEEL DOOR W/ CLOSERSTANDARD EXIT103.13'-0"X7'-0"EXISTING STEEL INSULATED DOOR W/ HALF GLASS W/ CLOSERPANIC105.13'-0"X7'-0"NEW WOOD DOORPRIVACY106.1(2) 3'-0"X7'-0"NEW DOUBLE DOORSTANDARD EXIT106.23'-0"X7'-0"NEW ALUMINUM STOREFRONT DOOR W/ CLOSERPANIC106.33'-4"X7'-0"EXISTING INSULATED STEEL DOOR W/ CLOSERPANIC107.1(2) 3'-0"X7'-0"NEW DOUBLE DOORSTANDARD EXIT107.23'-0"X7'-0"NEW WOOD DOORPANIC108.13'-0"X7'-0"NEW INSULATED STEEL DOOR W/ CLOSERPANIC109.13'-0"X7'-0"NEW WOOD DOORPRIVACY110.13'-0"X7'-0"NEW WOOD DOORPRIVACY111.13'-0"X7'-0"NEW WOOD DOORSTANDARD EXIT112.13'-0"X7'-0"NEW WOOD DOORSTANDARD EXIT113.13'-0"X7'-0"NEW WOOD DOORPRIVACY114.13'-0"X7'-0"NEW WOOD DOORPRIVACY115.13'-0"X7'-0"NEW WOOD DOORPRIVACY116.13'-0"X7'-0"NEW INSULATED STEEL DOOR W/ CLOSERSTANDARD EXIT118.1(2) 3'-0"X7'-0"NEW DOUBLE ALUMINUM STOREFRONT DOOR W/ CLOSERPANIC118.215'-0"X14'-0"EXISTING INSULATED GLASS OVERHEAD DOOROPERATOR118.33'-4"X7'-0"EXISTING INSULATED STEEL DOOR W/ CLOSERPANIC118.43'-0"X7'-0"NEW DOUBLE ALUMINUM STOREFRONT DOOR W/ CLOSERPANIC119.1(2) 3'-0"X7'-0"NEW DOUBLE ALUMINUM STOREFRONT DOOR W/ CLOSERPANIC120.13'-6"X7'-0"EXISTING INSULATED STEEL DOOR W/ CLOSERSTANDARD EXIT121.13'-0"X7'-0"NEW WOOD DOORSTANDARD EXIT122.13'-0"X7'-0"NEW WOOD POCKET DOORSTANDARD EXIT125.13'-0"X7'-0"NEW INSULATED STEEL DOOR W/ CLOSERPANIC127.13'-0"X7'-0"NEW WOOD DOORPRIVACY DOOR REMARKS-ALL LOCKSETS TO BE LEVER TYPE AND ADA COMPLIANT.-ALL EXTERIOR DOORS SHALL HAVE ADA THRESHOLD, WEATHER STRIPPING, & CLOSER. LATCH GUARD ON DOOR 8.-ALL FIRE DOORS SHALL HAVE LABELED DOORS AND FRAMES. -WINDOW LOCATIONS ARE IN EXISTING BRICKED IN WINDOWS.-WINDOWS TO BE INSULATED LOW "E" GLASS REMARKS-ALL FINISHES SHALL COMPLY WITH IBC 2009 CHAPTER 8 & 12-ALL SHEET ROCK TO BE 5/8" TAPED, LIGHT SAND TEXTURE, 2 COATS ENAMEL PAINT, SMOOTH AT TOILET ROOMS.-M.R. S.R. - MOISTURE RESISTANT SHEET ROCK-GRAB BARS TO BE "BRADLEY" MODEL 812 112" O.D. 18 GA. STAINLESS STEEL 18", 36" AND 42" LONG, CONCEALED MOUNTINGS-F.E. - FIRE EXTINGUISHERS TO BE TYPE ABC. RECHARGEABLE, 10#. PROVIDE RECESSED CABINET.-ALL MATERIALS TO BE AS SPECIFIED OR EQUAL-EMERGENCY EXIT LIGHT W/ EGRESS LIGHTS & BATTERY PACK WITH EMERGENCY EXTERIOR LIGHT.-TOILET ROOM BASE SHALL BE A MINIMUM OF 4" IN HEIGHT-PARTITION WALLS TO BE INSULATED WITH FIBERGLASS SOUND BATTS.-PROVIDE ADA TOILET ROOM SIGNS AND VERTICAL HANDICAP PARKING SIGNS. Page 18 of 46 7'-014"7'-614" 10'-0"7'-914" MEZZANINE201 202.1OFFICE2021 PEOPLE 23 PEOPLE112" DIA STEEL GUARDRAIL 42"HIGH W/ INFILL SO A 4" SPHERECOULD NOT PASS 112" DIA STEEL HANDRAIL36" ABOVE RISER NOSING.PROVIDE 1'-0" HANDRAILEXTENSIONS TOP ANDBOTTOM OF STAIRS.112" DIA STEEL GUARDRAIL 42"HIGH W/ INFILL SO A 4" SPHERECOULD NOT PASSUNISEX003003.1BASEMENT001 40'-412" 70'-9" 29'-412" 002.1MECH0026'-6"512"7'-1012"312"5'-0"312" 7'-8"312"19'-5"11'-0" 112" DIA STEEL HANDRAIL36" ABOVE RISER NOSING.PROVIDE 1'-0" HANDRAILEXTENSIONS TOP ANDBOTTOM OF STAIRS. SUMP PITSTAIR126UP18R @ 6.44"17T @11" 2MEZZANINE FLOOR PLANSCALE: 1/8"=1'-0" DRAWN BY:CHECKED BY: 547 HEWETT ST.P.O. BOX 189NEILLSVILLE, WI 54456PHONE: 715.743.2240FAX: 715.743.4469WWW.RATSCHENGINEERING.COMPROJECT NAME:PROJECT DESCRIPTION:PROJECT ADDRESS: SHEET:SHEET DISCRIPTION: DISCLAIMER:ALTHOUGH DILIGENT EFFORTS HAVE BEEN MADE IN THE PREPARATION AND CHECKING OF THESE PLANS FOR ACCURACY, ALL CONTRACTORS SHALL CHECK, VERIFY AND BE RESPONSIBLE FOR ALL DETAILS AND DIMENSIONS. ALL CONTRACTORS SHALL EXAMINE THE SITE AND EXISTING CONDITIONS OF THE PROPOSED WORK. ALL CONTRACTORS SHALL REVIEW ALL PLAN PAGES FOR WORK IN THEIR CONTRACT. ALL WORK ON THIS PROJECT IS TO BE GOVERNED BY THE LATEST EDITION OF THE CODESAPPLICABLE TO THE LOCAL ORDINANCES. ALL WORK SHALL BE PERFORMED IN ACCORDANCE WITH ACCEPTED BUILDING PRACTICES AND INDUSTRY STANDARDS. VERIFY AND USE ONLY WRITTEN DIMENSIONS. DO NOT SCALE OR MEASURE DIMENSIONS DIRECTLY FROM PRINT. ALL CONTRACTORS MUST BE RESPONSIBLE FOR ALL AND ANY DAMAGE TO "EXISTING" STRUCTURE CAUSED EITHER DIRECTLY OR INDIRECTLY BY THEIR TRADES. VERIFY ANY UNCERTAIN ITEMS WITH OWNER, BUILDER, AND/ORENGINEER. ENGINEER WILL NOT BE RESPONSIBLE FOR EXISTING OR PREEXISTING SOIL OR STRUCTURAL CONDITIONS. THE ENGINEER WILL NOT BE RESPONSIBLE FOR CONSTRUCTION MEANS, METHODS, TECHNIQUES, SEQUENCES, OR PROCEDURES, OR FOR SAFETY PRECAUTIONS AND PROGRAMS IN CONNECTION WITH THE WORK AND HE SHALL NOT BE RESPONSIBLE FOR THE CONTRACTOR'S FAILURE TO CARRY OUT THE WORK IN ACCORDANCE WITH THE CONTRACT DOCUMENTS. CONTRACTOR SHALL REVIEWALL SHOP DRAWINGS PRIOR TO SUBMITTAL TO ENGINEER. PLAN SET:PRELIMINARYSCALE:DATE:REVISION: SHEET SIZE:ARCH D 36X24ALTENBURG - CENTER CITY MARKETPROPOSED MERCANTILE/ASSEMBLY ADDITION/ALTERATION2041 MADISON STREET STEVENS POINT, WISCONSIN 54481 10/27/2025 A1.2 SLSMEZZANINE & BASEMENT FLOOR PLANSAS NOTED--- ------------------------ 1BASEMENT FLOOR PLANSCALE: 1/8"=1'-0" ROOM FINISH SCHEDULEROOM NUMBERROOM NAMEFLOORBASEWALLSCEILINGHEIGHTNOTES 001BASEMENTEXISTING SEALED CONCRETENONECONCRETEPRECAST9'-0" 002MECHEXISTING SEALED CONCRETENONECONCRETEPRECAST- 003UNISEXEXISTING SEALED CONCRETENONECONCRETEPRECAST9'-0" 201MEZZANINEEXISTINGVINYLEXISTINGEXISTING9'-0" 202OFFICEEXISTINGVINYLPTD GYP BDSUSPENDEDDOOR SCHEDULEDOORNUMBERDOOR SIZEDESCRIPTIONHARDWARENOTES002.1 3'-0"X7'-0"NEW WOOD DOORSTANDARD EXIT003.1 3'-0"X7'-0"NEW WOOD DOORPRIVACY202.1 3'-0"X7'-0"NEW WOOD DOORSTANDARD EXIT 4 PEOPLE Page 19 of 46 40'-0" 70'-0" BAKERY120 OFFICE121 ELEC125 5'-0"312"9'-0"512" 40'-0"15'-812" 512"312" 11'-0" 125.1120.1 STAIR126 A A A A B 8'-612"312"8'-5"312"6'-0"11'-812" A A ASTORAGE /RECEIVING ORDER PREPSHEETINGAREADISH PIT DISH DROPOFF FDISH DROPOFF OPENING OPTION 2DUMBWAITER OPTION 1DUMBWAITER 6'-0" WALL6'-0" WALL6'-0" TALLWALL OFFICE122 16'-0"FREEZER124 COOLER123 B VERIFY NON-COMBUSTIBLEMATERIAL BEHIND HOOD 120.1121.1 15'-512" 312" 5'-0"312"3'-6"18'-312" CLOSET127127.1 34'-212" 4'-0"22'-0"4'-0"6'-1112"3'-6"11'-612" 14'-4"3'-0"8"18'-0"4'-0"7'-0"4'-0"7'-0" 7'-0"4'-0"7'-0"4'-0"7'-0" 4'-0"7'-0" 1'-2"2'-6" 17'-612" 12'-0"13'-7" 17'-6"7'-612" 10'-2"20'-0"2'-212" DOWN18R @ 6.44"17T @11" 1FIRST FLOOR PLANSCALE: 1/8"=1'-0" DRAWN BY:CHECKED BY: 547 HEWETT ST.P.O. BOX 189NEILLSVILLE, WI 54456PHONE: 715.743.2240FAX: 715.743.4469WWW.RATSCHENGINEERING.COMPROJECT NAME:PROJECT DESCRIPTION:PROJECT ADDRESS: SHEET:SHEET DISCRIPTION: DISCLAIMER:ALTHOUGH DILIGENT EFFORTS HAVE BEEN MADE IN THE PREPARATION AND CHECKING OF THESE PLANS FOR ACCURACY, ALL CONTRACTORS SHALL CHECK, VERIFY AND BE RESPONSIBLE FOR ALL DETAILS AND DIMENSIONS. ALL CONTRACTORS SHALL EXAMINE THE SITE AND EXISTING CONDITIONS OF THE PROPOSED WORK. ALL CONTRACTORS SHALL REVIEW ALL PLAN PAGES FOR WORK IN THEIR CONTRACT. ALL WORK ON THIS PROJECT IS TO BE GOVERNED BY THE LATEST EDITION OF THE CODESAPPLICABLE TO THE LOCAL ORDINANCES. ALL WORK SHALL BE PERFORMED IN ACCORDANCE WITH ACCEPTED BUILDING PRACTICES AND INDUSTRY STANDARDS. VERIFY AND USE ONLY WRITTEN DIMENSIONS. DO NOT SCALE OR MEASURE DIMENSIONS DIRECTLY FROM PRINT. ALL CONTRACTORS MUST BE RESPONSIBLE FOR ALL AND ANY DAMAGE TO "EXISTING" STRUCTURE CAUSED EITHER DIRECTLY OR INDIRECTLY BY THEIR TRADES. VERIFY ANY UNCERTAIN ITEMS WITH OWNER, BUILDER, AND/ORENGINEER. ENGINEER WILL NOT BE RESPONSIBLE FOR EXISTING OR PREEXISTING SOIL OR STRUCTURAL CONDITIONS. THE ENGINEER WILL NOT BE RESPONSIBLE FOR CONSTRUCTION MEANS, METHODS, TECHNIQUES, SEQUENCES, OR PROCEDURES, OR FOR SAFETY PRECAUTIONS AND PROGRAMS IN CONNECTION WITH THE WORK AND HE SHALL NOT BE RESPONSIBLE FOR THE CONTRACTOR'S FAILURE TO CARRY OUT THE WORK IN ACCORDANCE WITH THE CONTRACT DOCUMENTS. CONTRACTOR SHALL REVIEWALL SHOP DRAWINGS PRIOR TO SUBMITTAL TO ENGINEER. PLAN SET:PRELIMINARYSCALE:DATE:REVISION: SHEET SIZE:ARCH D 36X24ALTENBURG - CENTER CITY MARKETPROPOSED MERCANTILE/ASSEMBLY ADDITION/ALTERATION2041 MADISON STREET STEVENS POINT, WISCONSIN 54481 10/27/2025 A1.3 SLSENLARGED BAKERY FLOOR PLANAS NOTED--- ------------------------ Page 20 of 46 MASONRY VENEERVERTICAL PAINTEDSIDING MASONRY VENEERVERTICAL PAINTEDSIDING 122.5 MASONRY VENEERVERTICAL PAINTEDSIDING MASONRYVENEERVERTICALPAINTEDSIDINGMASONRY VENEERVERTICAL PAINTEDSIDINGMASONRYVENEERVERTICALPAINTEDSIDING DRAWN BY:CHECKED BY: 547 HEWETT ST.P.O. BOX 189NEILLSVILLE, WI 54456PHONE: 715.743.2240FAX: 715.743.4469WWW.RATSCHENGINEERING.COMPROJECT NAME:PROJECT DESCRIPTION:PROJECT ADDRESS: SHEET:SHEET DISCRIPTION: DISCLAIMER:ALTHOUGH DILIGENT EFFORTS HAVE BEEN MADE IN THE PREPARATION AND CHECKING OF THESE PLANS FOR ACCURACY, ALL CONTRACTORS SHALL CHECK, VERIFY AND BE RESPONSIBLE FOR ALL DETAILS AND DIMENSIONS. ALL CONTRACTORS SHALL EXAMINE THE SITE AND EXISTING CONDITIONS OF THE PROPOSED WORK. ALL CONTRACTORS SHALL REVIEW ALL PLAN PAGES FOR WORK IN THEIR CONTRACT. ALL WORK ON THIS PROJECT IS TO BE GOVERNED BY THE LATEST EDITION OF THE CODESAPPLICABLE TO THE LOCAL ORDINANCES. ALL WORK SHALL BE PERFORMED IN ACCORDANCE WITH ACCEPTED BUILDING PRACTICES AND INDUSTRY STANDARDS. VERIFY AND USE ONLY WRITTEN DIMENSIONS. DO NOT SCALE OR MEASURE DIMENSIONS DIRECTLY FROM PRINT. ALL CONTRACTORS MUST BE RESPONSIBLE FOR ALL AND ANY DAMAGE TO "EXISTING" STRUCTURE CAUSED EITHER DIRECTLY OR INDIRECTLY BY THEIR TRADES. VERIFY ANY UNCERTAIN ITEMS WITH OWNER, BUILDER, AND/ORENGINEER. ENGINEER WILL NOT BE RESPONSIBLE FOR EXISTING OR PREEXISTING SOIL OR STRUCTURAL CONDITIONS. THE ENGINEER WILL NOT BE RESPONSIBLE FOR CONSTRUCTION MEANS, METHODS, TECHNIQUES, SEQUENCES, OR PROCEDURES, OR FOR SAFETY PRECAUTIONS AND PROGRAMS IN CONNECTION WITH THE WORK AND HE SHALL NOT BE RESPONSIBLE FOR THE CONTRACTOR'S FAILURE TO CARRY OUT THE WORK IN ACCORDANCE WITH THE CONTRACT DOCUMENTS. CONTRACTOR SHALL REVIEWALL SHOP DRAWINGS PRIOR TO SUBMITTAL TO ENGINEER. PLAN SET:PRELIMINARYSCALE:DATE:REVISION: SHEET SIZE:ARCH D 36X24ALTENBURG - CENTER CITY MARKETPROPOSED MERCANTILE/ASSEMBLY ADDITION/ALTERATION2041 MADISON STREET STEVENS POINT, WISCONSIN 54481 10/27/2025 A2.1 SLSELEVATIONSAS NOTED--- ------------------------ 1WEST ELEVATIONSCALE: 1/8"=1'-0" 2EAST ELEVATIONSCALE: 1/8"=1'-0" 5NORTH ELEVATIONSCALE: 1/8"=1'-0" 4NORTH ELEVATION - CUT-THROUGHSCALE: 1/8"=1'-0" 3SOUTH ELEVATIONSCALE: 1/8"=1'-0" Page 21 of 46 BRICK VENEER W/ BRICK TIES24" O.C. HORIZ. & 16" O.C. VERT.1" AIR GAPSTONE CAP7/16" SHEATHING W/ 8DNAILS 6" O.C. AT EDGES &12" O.C. AT INTERMEDIATETYVEKWOOD LAP SIDINGINSULATION R-212X6 DFL #2 OR BETTER16" O.C.FRP OVER 12" PLYWOODVINYL SUSPENDED CEILING12" PLYWOODPRE-ENGINEERED ROOFTRUSSES 2'-0" O.C. USP RT16ATRUSS CLIPS5/8" SHEATHING W/ EDGE CLIPS &8d NAILS 6" O.C. AT THE EDGES &12" O.C. AT INTERMEDIATEMETAL SALES IMAGE II COLORED 24 GASTANDING SEAM ROOF W/ MS COLORFAST 45 OR EQUAL. PROVIDE ALLREQUIRED ACCESSORIES & TRIM. MIN.PANEL 12", MAX. PANEL 24" FASCIA ANDSOFFIT13'-412"11'-0" 21212 8'-9"10'-0"1'-0" 70'-0"70'-9"2'-0" 1'-0"3"8"4" NERVASTRAL FLASHINGWEEP HOLES 32" O.C.FLASHING INSULATION R-60 3" CONCRETE TOP 4" CONCRETE FLOOR W/#4 BARS 2'-0" O.C. B.W. PRECAST CONCRETE FLOOR 24"X12" CONCRETE FOOTINGW/ (2) #4 BARS HORIZ - 15" LAP12"X10'-0" FOUNDATION WALLW/ #5 BARS 20" O.C. VERT. &16" O.C. HORIZ.6 MIL POLY 6 MIL POLY SYNTHETIC FELT DUPONT120 OR EQUALHIGH TEMP ICE GUARD - OWENSCORING TITANIUM PSU 30 OREQUAL. SHALL EXTEND A MIN OF24" ONTO THE BUILDING PASTTHE EXTERIOR WALL NOTE:THE THICKNESS OF BLOWN IN OR SPARED ROOF/CEILINGINSULATION (FIBERGLASS OR CELLULOSE) SHALL BE WRITTENIN INCHES ON MARKERS THAT ARE INSTALLED AT LEAST ONEEVERY 300 SQUARE FEET THROUGHOUT THE ATTIC SPACE.THE MARKERS SHALL BE AFFIXED TO THE TRUSSES OR JOISTAND MARKED WITH THE MINIMUM INITIAL INSTALLEDTHICKNESS WITH NUMBERS A MINIMUM OF 1" IN HEIGHT. EACHMARKER SHALL FACE THE ATTIC ACCESS OPENING. 4" DIA PERFORATED DRAINTILE WITH FABRIC SOCK.DRAIN TO SUMP PIT.PEA GRAVELFABRICPLATON MEMBRANE SYSTEMSILL SEAL12"X15" ANCHOR BOLT 4'-0" O.C.2" STYROFOAM INSULATIONR-10 12" THERMAX - R3.3 5'-0"14'-0" 4'-0" PRE-ENGINEERED ROOFTRUSSES 2'-0" O.C. USP RT16ATRUSS CLIPS5/8" SHEATHING W/ EDGE CLIPS &8d NAILS 6" O.C. AT THE EDGES &12" O.C. AT INTERMEDIATEMETAL SALES IMAGE II COLORED 24 GASTANDING SEAM ROOF W/ MS COLORFAST 45 OR EQUAL. PROVIDE ALLREQUIRED ACCESSORIES & TRIM. MIN.PANEL 12", MAX. PANEL 24"SYNTHETIC FELT DUPONT120 OR EQUALINSULATION R-60VINYL SUSPENDED CEILING12" PLYWOOD INSULATION R-212X6 DFL #2 OR BETTER16" O.C.FRP OVER 12" PLYWOOD 3" CONCRETE TOP8" PRECAST CONCRETE FLOOR 4" CONCRETE FLOOR W/#4 BARS 2'-0" O.C. B.W.6 MIL POLY 7/16" SHEATHING W/ 8DNAILS 6" O.C. AT EDGES &12" O.C. AT INTERMEDIATETYVEKWOOD LAP SIDING FASCIA ANDSOFFIT 4" CONCRETE FLOOR W/#4 BARS 2'-0" O.C. B.W. 24"X12" CONCRETE FOOTINGW/ (2) #4 BARS HORIZ - 15" LAP12"X9'-0" FOUNDATION WALLW/ #5 BARS 20" O.C. VERT. &16" O.C. HORIZ. 9'-8"24"X12" CONCRETE FOOTINGW/ (2) #4 BARS HORIZ - 15" LAP12"X10'-0" FOUNDATION WALLW/ #5 BARS 20" O.C. VERT. &16" O.C. HORIZ.4" DIA PERFORATED DRAINTILE WITH FABRIC SOCK.DRAIN TO SUMP PIT.PEA GRAVELFABRICPLATON MEMBRANE SYSTEM12"X15" ANCHOR BOLT 4'-0" O.C.4"8"1'-0"BRICK VENEER W/ BRICK TIES24" O.C. HORIZ. & 16" O.C. VERT.1" AIR GAPSTONE CAPNERVASTRAL FLASHINGWEEP HOLES 32" O.C.FLASHINGSILL SEAL 3'-0"1'-0" 112" DIA STEEL HANDRAIL 36"ABOVE RISER NOSING. PROVIDE1'-0" HANDRAIL EXTENSIONS TOPAND BOTTOM OF STAIRS2" STYROFOAM INSULATIONR-10 12" THERMAX - R3.3 #5 VERTICAL BARSCENTERED IN CORE 32"O.C.BOND BEAM W/ (2) #5LONGITUDINAL (1) EACHFACE AT 40" O.C. GYP BD6" STEEL STUDJOISTS 16" O.C. 8" CMU WALL HILTI XUx178" 16" O.C.1'-4"8'-414"VERIFY8'-412"X1'-4" FOOTINGWITH #4 BARS HORIZ -15" LAP8"X16" CONCRETEFOOTING W/ (2) #4 BARSHORIZ - 15" LAPDRAWN BY:CHECKED BY: 547 HEWETT ST.P.O. BOX 189NEILLSVILLE, WI 54456PHONE: 715.743.2240FAX: 715.743.4469WWW.RATSCHENGINEERING.COMPROJECT NAME:PROJECT DESCRIPTION:PROJECT ADDRESS: SHEET:SHEET DISCRIPTION: DISCLAIMER:ALTHOUGH DILIGENT EFFORTS HAVE BEEN MADE IN THE PREPARATION AND CHECKING OF THESE PLANS FOR ACCURACY, ALL CONTRACTORS SHALL CHECK, VERIFY AND BE RESPONSIBLE FOR ALL DETAILS AND DIMENSIONS. ALL CONTRACTORS SHALL EXAMINE THE SITE AND EXISTING CONDITIONS OF THE PROPOSED WORK. ALL CONTRACTORS SHALL REVIEW ALL PLAN PAGES FOR WORK IN THEIR CONTRACT. ALL WORK ON THIS PROJECT IS TO BE GOVERNED BY THE LATEST EDITION OF THE CODESAPPLICABLE TO THE LOCAL ORDINANCES. ALL WORK SHALL BE PERFORMED IN ACCORDANCE WITH ACCEPTED BUILDING PRACTICES AND INDUSTRY STANDARDS. VERIFY AND USE ONLY WRITTEN DIMENSIONS. DO NOT SCALE OR MEASURE DIMENSIONS DIRECTLY FROM PRINT. ALL CONTRACTORS MUST BE RESPONSIBLE FOR ALL AND ANY DAMAGE TO "EXISTING" STRUCTURE CAUSED EITHER DIRECTLY OR INDIRECTLY BY THEIR TRADES. VERIFY ANY UNCERTAIN ITEMS WITH OWNER, BUILDER, AND/ORENGINEER. ENGINEER WILL NOT BE RESPONSIBLE FOR EXISTING OR PREEXISTING SOIL OR STRUCTURAL CONDITIONS. THE ENGINEER WILL NOT BE RESPONSIBLE FOR CONSTRUCTION MEANS, METHODS, TECHNIQUES, SEQUENCES, OR PROCEDURES, OR FOR SAFETY PRECAUTIONS AND PROGRAMS IN CONNECTION WITH THE WORK AND HE SHALL NOT BE RESPONSIBLE FOR THE CONTRACTOR'S FAILURE TO CARRY OUT THE WORK IN ACCORDANCE WITH THE CONTRACT DOCUMENTS. CONTRACTOR SHALL REVIEWALL SHOP DRAWINGS PRIOR TO SUBMITTAL TO ENGINEER. PLAN SET:PRELIMINARYSCALE:DATE:REVISION: SHEET SIZE:ARCH D 36X24ALTENBURG - CENTER CITY MARKETPROPOSED MERCANTILE/ASSEMBLY ADDITION/ALTERATION2041 MADISON STREET STEVENS POINT, WISCONSIN 54481 10/27/2025 A2.2 SLSCROSS SECTIONSAS NOTED--- ------------------------ 1CROSS SECTION ASCALE: 1/4"=1'-0" 2CROSS SECTION BSCALE: 1/4"=1'-0"3LULA CROSS SECTIONSCALE: 1/4"=1'-0" Page 22 of 46 PRE-ENGINEERED ROOF TRUSSES2'-0" O.C. USP RT16A TRUSS CLIPS PRE-ENGINEERED ROOF TRUSSES2'-0" O.C. USP RT16A TRUSS CLIPS10'-8"8'-8"2'-0" 10'-8"8'-8"2'-0"12'-5"8'-5"2'-0"2'-0" 41'-4" 41'-4" 72'-8"70'-0"1'-4"1'-4"40'-0"1'-4" 40'-0"1'-4" 10.37'91.6PSF38.5PSFHDHDHDHDH2 HD HD HD HD HD HD HD HD HDHDHDHDHDHD H2H2H2 H2 H1H1H1 H1H1 24"X12" CONCRETE FOOTING W/ (2)#4 BARS HORIZ - 15" LAP4" CONCRETE FLOOR W/ #4 BARS2'-0" O.C. B.W.8"X48" FOUNDATION WALL W/ #4BARS 4'-0" O.C. VERT. & 16" O.C.HORIZ. 4" CONCRETE FLOOR W/ #4 BARS2'-0" O.C. B.W. 12"X9'-0" FOUNDATION WALL W/ #4BARS 4'-0" O.C. VERT. & 16" O.C.HORIZ.24"X12" CONCRETE FOOTING W/ (2)#4 BARS HORIZ - 15" LAP 12"X10'-0" FOUNDATION WALL W/#5 BARS 20" O.C. VERT. & 16" O.C.HORIZ.24"X12" CONCRETE FOOTING W/ (2)#4 BARS HORIZ - 15" LAP70'-9" 40'-0"28'-0"12'-0" 8'-5"8'-8"8'-8" 40'-412"28'-0"12'-0" FLOOROPENING 27'-412" 4"1'-0"4"1'-0" 48'-712"5'-0"15'-112" 68'-9"4'-10"14'-0"8'-612"4" 4"27'-412" 8" PRECAST CONCRETE PLANKW/ 3" CONCRETE TOPPING 1FOUNDATION PLANSCALE: 1/8"=1'-0" DRAWN BY:CHECKED BY: 547 HEWETT ST.P.O. BOX 189NEILLSVILLE, WI 54456PHONE: 715.743.2240FAX: 715.743.4469WWW.RATSCHENGINEERING.COMPROJECT NAME:PROJECT DESCRIPTION:PROJECT ADDRESS: SHEET:SHEET DISCRIPTION: DISCLAIMER:ALTHOUGH DILIGENT EFFORTS HAVE BEEN MADE IN THE PREPARATION AND CHECKING OF THESE PLANS FOR ACCURACY, ALL CONTRACTORS SHALL CHECK, VERIFY AND BE RESPONSIBLE FOR ALL DETAILS AND DIMENSIONS. ALL CONTRACTORS SHALL EXAMINE THE SITE AND EXISTING CONDITIONS OF THE PROPOSED WORK. ALL CONTRACTORS SHALL REVIEW ALL PLAN PAGES FOR WORK IN THEIR CONTRACT. ALL WORK ON THIS PROJECT IS TO BE GOVERNED BY THE LATEST EDITION OF THE CODESAPPLICABLE TO THE LOCAL ORDINANCES. ALL WORK SHALL BE PERFORMED IN ACCORDANCE WITH ACCEPTED BUILDING PRACTICES AND INDUSTRY STANDARDS. VERIFY AND USE ONLY WRITTEN DIMENSIONS. DO NOT SCALE OR MEASURE DIMENSIONS DIRECTLY FROM PRINT. ALL CONTRACTORS MUST BE RESPONSIBLE FOR ALL AND ANY DAMAGE TO "EXISTING" STRUCTURE CAUSED EITHER DIRECTLY OR INDIRECTLY BY THEIR TRADES. VERIFY ANY UNCERTAIN ITEMS WITH OWNER, BUILDER, AND/ORENGINEER. ENGINEER WILL NOT BE RESPONSIBLE FOR EXISTING OR PREEXISTING SOIL OR STRUCTURAL CONDITIONS. THE ENGINEER WILL NOT BE RESPONSIBLE FOR CONSTRUCTION MEANS, METHODS, TECHNIQUES, SEQUENCES, OR PROCEDURES, OR FOR SAFETY PRECAUTIONS AND PROGRAMS IN CONNECTION WITH THE WORK AND HE SHALL NOT BE RESPONSIBLE FOR THE CONTRACTOR'S FAILURE TO CARRY OUT THE WORK IN ACCORDANCE WITH THE CONTRACT DOCUMENTS. CONTRACTOR SHALL REVIEWALL SHOP DRAWINGS PRIOR TO SUBMITTAL TO ENGINEER. PLAN SET:PRELIMINARYSCALE:DATE:REVISION: SHEET SIZE:ARCH D 36X24ALTENBURG - CENTER CITY MARKETPROPOSED MERCANTILE/ASSEMBLY ADDITION/ALTERATION2041 MADISON STREET STEVENS POINT, WISCONSIN 54481 10/27/2025 S1.1 SLSFOUNDATION & ROOF FRAMING PLANSAS NOTED--- ------------------------ 2ROOF FRAMING PLANSCALE: 1/8"=1'-0" 3FIRST FLOOR FRAMING PLANSCALE: 1/8"=1'-0" HEADERS AND HOLDDOWNS:H1 - (2) 134"X914" MICROLAM LVL W/ (3) SHOULDER STUDS EACH ENDH2 - (2) 2X5 SPF #2 W/ (1) SHOULDER STUD EACH ENDHD - HOLDDOWN ANCHOR - USP HTT16 W/ (18) 10d NAILS INTO DOUBLESTUD W/ 58"X15" ANCHOR BOLT (TOTAL 18) Page 23 of 46   1 ( :  $ ' ' , 7 , 2 1  8 3 3 ( 5  ( , ) 6  ) , 1 , 6 +  6 . , 3  7 5 2 : ( / ( '   , 1  % ( 1 - $ 0 , 1  0 2 2 5 (  + , 6 7 2 5 , & $ /  & 2 / 2 5   + $ 7 + $ : $ <  3 ( $ & +  + &      1 ( :  $ ' ' , 7 , 2 1  / 2 : ( 5   & 2 1 & 5 ( 7 (  9 ( 1 ( ( 5   ) , 1 , 6 +  7 2  5 ( 6 ( 0 % / (  ( ; , 6 7 , 1 *  % 8 , / ' , 1 *  / 2 : ( 5  7 < 3    1 ( :  0 ( 7 $ /  ) ( 1 & (  , 1  % / $ & .  ) , 1 , 6 + & ( 1 7 5 $ /  & , 7 <  0 $ 5 . ( 7    6 2 8 7 + ( $ 6 7  3 ( 5 6 3 ( & 7 , 9 ( + , 6 7 2 5 , & $ /  5 ( 9 , ( :  1 2 7 ( 6            Page 24 of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age 25 of 46 NOT LUMBER OR PAPER, BUT STILL A BIG INDUSTRY The Pinery Iron Works As everyone knows, Stevens Point was put on the map by the logging industry, and kept there for many years by the papermaking business. But there were other enterprises as well—the railroads and Sentry Insurance come to mind. Yet another industry was a very heavy one: the making of objects of iron and steel. And Stevens Point had several, if not many, foundries or machine shops over the decades. The longest-lived of these was Richard Cook’s establishment, which ran under various names for over 50 years. When exactly the first foundry or machine shop started in Stevens Point, is hard to pinpoint, but a history of his company published in the July 15, 1893, Stevens Point Journal, tries. According to it, “The original plant was established in the ’40s by Robb & Craig, on the banks of the Wisconsin river at the foot of Main street. ” Then, the article continues, that shop was sold to the William Weston & Sons sawmill, “who afterwards sold it to Merrill Whitney & Steel, who conducted it till 1874, when Sayler & Cook purchased it, and in 1879 built new shops near the Curran House, continuing business there five or six years when Mr. Sayler sold his interest to Geo. A. Packard, and after three years Mr. R.A. Cook bought Mr. Packard’s interest and has since been sole proprietor. In 1890 the works burned, and Mr. Cook then purchased about 2 ½ acres of land fronting on Madison, Monroe and Reserve streets, and in the spring of 1892 erected his present commodious brick buildings…. ” This history is accurate in general, but it contains some minor errors, and omits some details. No corroborating evidence has been found for Robb and Craig, the apparent founders of the city’s first machine shops, nor has any information been found about them. The 1840 and 1850 U.S. censuses contain no mention of them, for example. There is lots of information about William Weston’s sawmill, but none so far about his buying or owning a foundry. The first owners mentioned in the Journal’s sketch that can be verified in other sources are Whitney, Merrill, and Steele—that is, John Whitney, W.F. Merrill, and Garvin Steele. Their ad appeared in the Journal of April 20, 1875, when they called their company the Pinery Iron Works. PINERY IRON WORKS, STEVENS POINT, WIS., WHITNEY, MERRILL & STEELE, Prop’s. Manufacturers of Steam Engines, BOILERS, GRIST AND SAW MILL Machinery. Also SHINGLE MILLS AND Whitney’s Patent GANG EDGER, SHAFTING, PULLEYS and GEARING Of all kinds. IRON AND BRASS CASTINGS. --REPAIRS DONE PROMPTLY— And Satisfaction Guaranteed. We also keep in stock STEAM and WATER PIPES and FITTINGS Brass and Iron. Stevens Point, April 20, 1875. In any case, they did not own or operate this business much longer. The August 14, 1875, Journal printed an ad announcing a “DISSOLUTION OF CO-PARTNERSHIP . The partnership existing between Whitney, Merrill & Steele is this day dissolved by mutual consent. Dated Aug. 4, 1875. JOHN WHITNEY, W.F. MERRILL, GARVIN STEELE. The business will be continued at the same place by John Whitney, who will collect and pay all the accounts of the firm. W., M., & S. ” True to his statement in the dissolution notice, Whitney continued alone in business, according to the Journal of October 21, 1876: “MR. JOHN WHITNEY, at the Pinery Iron Works, is now [turning] out half a dozen of his celebrated shingle machines. Three of them have been ordered by Chicago parties, for use in the Michigan pineries, and some parties are contemplating sending two of them to the Black Hills. ” But eventually he sold his business and apparently left town. One reason may have been the death of his wife. Page 26 of 46 Her obituary was printed in the September 9, 1876, Journal: “DIED. In this city, September 1st, 1876, of consumption, after a long and painful sickness extending over five years, Emily A., wife of John Whitney, aged 41 years, 9 months and 15 days. ” Only about two years later, a report in the June 2, 1877, Journal said that the Pinery Iron Works had “Changed Hands, ” without calling the firm by its name. The report also introduced us to an owner we had not heard of before: G.W. Oaks. “The foundry and machine shops at the foot of Main street, for a few months past owned by G.W. Oaks & Co., were on Tuesday sold to Seyler & Cook. The former has been a resident of Stevens Point for the past two years or more, and has been engaged in the manufacture of boilers. The latter has been employed in the capacity of foreman at Rice Bros. ’ shops. The new firm propose to start business next week. ” An ad for the Pinery Iron Works in the June 9, 1877, Journal confirmed the sale. Pinery Iron Works SEYLER & COOK, Props. -Manufacturers of – Steam Engines, Boilers, Smoke Stacks and Breeching, CIRCULAR SAW MILLS And Mill Gearing Of Every Description. We shall keep in stock a full line of Steam and Gas Fittings, ENGINE TRIMMINGS. All work left with us will receive prompt attention, and satisfaction guaranteed. Special attention given to the REPAIRS OF MACHINERY AND BOILERS. YOUR PATRONAGE SOLICITED. Shop foot of Main street, near River. (The July 11, 1874, Stevens Point Journal announced the opening of Daniel Seyler’s boiler shop, his debut in business in Stevens Point: (“The new boiler shop in this city is now open and ready for business. Mr. Seyler, the proprietor, comes to us bearing the highest recommendations from those for whom he has worked, as a first-class workman, and honest, reliable man. We trust his investment may prove a profitable one, and certain it is that the mill men in this section should give the enterprise the encouragement of their patronage…. ” (Seyler’s ad, in the same issue of the Journal, described his services. Daniel Seyler, Proprietor of the Stevens Point Boiler Works Manufacturer of BOILERS Of all descriptions, sheet iron work, IRON DOORS, SHUTTERS, ETC. Repairing promptly done and all work Guaranteed. Shop on Plank road, near Depot. Stevens Point, Wis. (Plank Road was that part of Water Street that lay south of the Wisconsin Central Railroad tracks.) (According to the 1880 U.S. Census, Daniel Seyler was born in about 1847 in Bavaria, Germany (his wife, Ernestina, was born in Prussia), and he had five children aged nine to one years. His occupation is given as “Boiler Maker. ” (Just below Daniel’s entry in the census record is one for a Jacob Seyler, Jacob was four years older than Daniel (37 years as opposed to 33), but also born in Bavaria and also listed as a boilermaker. So the two must have been brothers, and probably worked in, or even co-owned, the same foundry. Page 27 of 46 (Daniel’s son Daniel’s obituary, in the December 9, 1882, Journal, is brief: “DIED. SEYLER—In this city Sunday morning, Nov. 25, 1882, Daniel J. son of Daniel and Ernestina Seyler, aged 5 years and 3 months. ” (One clue as to what became of Daniel Seyler, Sr., appears in an article in The Gazette of December 5, 1894. “The Novelty Iron Works, at Ashland, was completely destroyed by fire, last Thursday morning. The loss is placed at $25,000, with only $3,000 insurance. D.J. Seyler, the proprietor, removed from this city to Ashland ten years ago, and had built up a large business. ” (More evidence of Seyler’s presence in Ashland is in the city directory of 1888: “Seyler Daniel J, Proprietor Novelty Iron Works Bay n e cor. Ninth ave E, res 819 St. Clair. ” (Another clue about Seyler appears in a “Special Schedule” of the 1890 U.S. Census that counted surviving Civil War veterans. According to it, Daniel Seyler was a corporal in Company M of the 7th New York Volunteer Artillery Regiment. He enlisted on January 8, 1864, and was discharged on July 2, 1865. (What ultimately became of Seyler—if he stayed in Ashland or moved away after his disastrous fire—is a mystery.) But while Seyler was a partner with R.A. Cook, their firm obviously prospered. The July 10, 1880, Journal reported on their expansion to new facilities. “INTO NEW QUARTERS. Seyler & Cook of the Pinery Iron Works, moved into their new machine shops on the north side of Main Street the first of the week. Their shop is roomy and convenient. In the front they have an office and stock room, with an entrance on Main St.; to the left is the machine shop, at the rear of which their blacksmith shop and engine house are located. The boilers and engine are enclosed with brick walls and well protected from fire. Their foundry will be located some two hundred feet to the rear and they are now engaged in remodeling the large barn, which occupied the rear end of the lot, for this purpose. They are now prepared to execute orders with promptness, and their increased facilities and commodious quarters will aid them materially in filling orders on short notice. Give the new shop a call. ” R.A. Cook & Company Foundry and Machine Shop when it was located at the west end of Main Street in Stevens Point, from 1881 to 1892. In foreground: a mower, one of the farm implements that the company stocked and sold at the time. Page 28 of 46 R.A. Cook & Company Dasniel Seyler sold his interest in the Pinery Iron Works to George A Packard in 1881, and the firm was renamed R.A. Cook & Company, according to the Journal of March 12. “BUSINESS CHANGE. The firm of Seyler & Cook, proprietors of the Pinery Iron Works, has been dissolved, Mr. Seyler having disposed of his interests to George A. Packard. The firm will hereafter be known as R.A. Cook & Co., and they will continue business at the same place. Of Dick Cook it is unnecessary to speak in [connection] with the machinists’ business, as all those who have patronized the late firm during the past three years know him to be a skilled mechanic and a pleasant gentleman to do business with. George A. Packard, the new member of the firm, is known to almost everybody here and hereabouts, and while he is not a machinist by trade, he proposes to take hold and learn. And then there are many things to do which he is familiar with, such as keeping the books, attending to the correspondence, collecting, &c.,--and these are by no means a minor part to any business. The new firm already have a good prospect for plenty of work and are determined to make a success of i t .” The Gazette of August 24, 1881, listed some of the kinds of products that the company made. “ AT R.A. COOK & CO’S These gentlemen are now crowded with work, as indeed they have been during the past several months, and are obliged to keep their large force of men at work night and day during a good portion of the time. At present they are furnishing a boiler and engine for Messrs. Langenburg & Podach, which will be used by these gentlemen in manufacturing of brick at their yard just north of this city…. Messrs. Cook & Co. are also manufacturing new pulleys and making a number of repairs for the saw mill of W.T. Price, at Unity, making shafting, pulleys, boxes, &c., to be used in the new addition to Brown Bros. planning mill, repairing machinery for Herren & Wadleigh’s planning mill, building a new bull-wheel for B.M. Holmes, of Ogema, making a new gang-edger and trimmer and doing a large amount of repairing for the saw and shingle mill of N. Boyington, in the town of Sharon, this county, as well as a goodly number of minor jobs. And still they say, let customers send on their work and they will turn it out on time, even if they have to enlarge their already commodious shops. ” In 1884, R.A. Cook & Co. began selling agricultural equipment and machinery, according to an article and ad in the March 15 issue of the Journal. “In another column will be found the advertisement of R.A. Cook & Co., calling attention to the stock of agricultural machinery which they now have on hand. They are prepared to fill orders at once and will be pleased to have farmers call and look over their stock. ” Farmers Look Here! Are you going to need any kind of Farm Machinery? If so, don’t fail to call on R.A. Cook & Co., Where you can find all kinds of FARM MACHINERY We are exclusive agents for the Champion Reapers, Mowers and Binders! Farmers when you come to the city don’t fail to call at our Warehouse, below Curran House on Main street, and see sample machines in operation. We sell every kind of machine a farmer needs from a harrow to a Steam Thresher. Don’t fail to call and see us. R.A. COOK & CO. In 1885, George Packard retired from his partnership with Richard Cook, the April 4 Journal reported. “ As will be seen by the official announcement published elsewhere, the firm of R.A. Cook & Co. was dissolved on Thursday, by George A. Packard retiring. The business will be continued by R.A. Cook, who will give it his undivided personal attention. He is a thoroughly practical man, having been engaged in the business for eighteen years, and will do all in his power to still further extend the large business they have built up during the past four years. Mr. Packard has not fully decided what he will do. We hope he will conclude to remain here, as he is a young man of good business ability and would make a success of most any business, as he certainly has of the Pinery Iron Works. “Joseph Pierron, who has been with the firm for several years, will be continued in the capacity of foreman. Mr. Pierron is thoroughly familiar with mill work of all kinds and a practical machinist of many years experience. ” Contrary to the Journal’s hopes, Packard did not remain in Stevens Point, but went to Hayward, Wisconsin, according to the Stevens Point Daily Journal of June 10, 1920. In Hayward, he “was employed in a bank and later engaged in the livery business. Moving to Bayfield, Mr. Packard became one of that city’s leading merchants and served as postmaster for a period of seventeen years. ” Later, he bought a large farm near Knoxville, Pennsylvania. Meanwhile, R.A. Cook took on yet another partner, C.J. Scribner of Fond du Lac, so the firm name again Page 29 of 46 became R.A. Cook & Co. The January 2, 1886, Journal reported that Scribner “has for the past few years been engaged as traveler for Vilas Bros., Chicago, dealers in paints and oils, and has a large acquaintance among mill men through this section of the state…. ” Probably under Scribner’s influence, the firm began stocking oils for sale, according to the February 27, 1886, Journal. “Messrs. R.A. Cook & Co., have added a full line of oils to supply illuminating and luminating [?] oils to the trade at the very lowest market quotations. Mr. Scribner has had five years experience in handling oils and knows just what their customers want. They want their goods first-class in every respect. ” Likewise, the company began stocking quantities of paint, the June 26, 1886, Journal reported. “PAINT! PAINT! By a special arrangement with the manufacturers we have purchased a large quantity of mixed paints which we are offering at an unusual low price of $1.10 per gallon in quantities to suit. This paint is made of pure lead and linseed oil, with sufficient coloring-ground in to give the desirable shade. This is the lowest price for which this quality of paint can be bought by jobbers and if you want to paint, now is your time to buy. Remember this paint is warranted not to [peel], crack or blister and will give satisfaction every time. We propose to lead in low prices and will never be undersold by anyone. R.A. COOK & CO. Despite this stocking of smaller hardware retails items, other news reports made it clear that the firm was still very much a heavy industry. For example, the Journal of April 24, 1886, reported that “R.A. Cook & Co. have taken the contract for building a complete saw mill for H.L. Beese of Butternut. They have already commenced work on some of the machinery and this job together with other mill work now in their shop will keep all hands going for several weeks. ” But at the end of the year, Cook’s partnership with Scribner also dissolved. According to the December 11, 1886, Journal, “The firm of R.A. Cook & Co., was dissolved on Monday last by C.J. Scribner retiring. The business will be continued by R.A. Cook, who has been at the head of the establishment for the past nine years. He is a first-class workman himself, and has always in the past and will in the future give the business his undivided attention. He has excellent facilities for turning out saw mill work of all kinds, and will be pleased to receive a call from those needing anything in his line. ” In 1890, Cook’s foundry was largely destroyed by fire, according to The Gazette of October 1. “ At about three o’clock last Thursday morning the machine shop of R.A. Cook was discovered on fire, the alarm being first sounded by the blowing of the Week Lumber Co. saw mill whistle. Soon the whole upper part of the structure was in flames, but this was subdued by hard work upon the arrival of the fire department. Upon the second floor hundreds of valuable patterns were stored…. These were very dry, and proved most acceptable fuel for the flames. The building, which was a wooden structure, was saved in a wrecked and entirely [worthless] condition, and will have to be replaced with brick or stone. The machinery was also considerably damaged, including the engine and boiler, in the rear…. The property was insured for $8,000, of which $4,500 was in Hyde’s agency, and $3,500 in Buckingham’s agency. The adjusters are now in the city for the purpose of fixing matters up with Mr. Cook, but as yet they have not agreed upon terms. Until then he cannot determine what will be done about rebuilding, but a new structure will undoubtedly take the place of the present ruins. ” In fact, Cook was to rebuild but not on his old site. He would pick a new site and a new name for his firm. Workmen pose for a photo of the Central City Iron Works as it looked originally, on Madison Street on Stevens Point’s South Side. Photo taken sometime after 1892. Page 30 of 46 R.A. Cook’s Central City Iron Works After the fire in his Main Street machine shops In September of 1890, it was almost two years before Richard Cook was ready for business in his new foundry, at his new location on Madison Street, on Stevens Point’s South Side. But when he finally started his new facility up, it was to be larger, more modern, and with far more business than he had at his old one. One reason for his increased volume of business was that he had secured a contract to make large castings for the Wisconsin Central Railroad, whose extensive yard bordered his own new grounds. Indeed, that proximity was one reason he built his new foundry where he did. All this information is contained in a long, detailed article in the February 20, 1892, Stevens Point Journal. According to it, Cook’s contract with the railroad meant an addition of $60,000 to $70,000 a year to his budget, a very large sum for the time. For his new plant, he “purchased the six lots between Madison and Monroe streets, adjoining the Central shops [where railroad cars were made and repaired]…. The new shop will be 40 x 210 feet. Eighty feet on the south end will be divided off for a foundry. The balance of the building will be used as a machine shop, wood-working shop and blacksmith shop. The engine and boiler room, which will be 14 x 24 feet, will be located on the east side. Both buildings will be solid brick with iron roof. The foundry will be supplied with a Collau furnace, one of the best made, with a capacity of from eight to ten ton daily. Both the foundry and machine shop will be fitted up with the very best machinery and appliances for doing first-class work. Mr. Cook does not expect to confine himself to railroad work, but will do a general custom business as he did before he was burned out…. In fact he expects to do more than double the amount of work he formerly did, in addition to the railroad work. His facilities in all departments will be greatly increased and the fact that he will cast every day, will bring a large amount of foundry work here which now goes below [south], and this will naturally tend to increase the work in the machine shop. Work on the new shop will be commenced as soon as the frost goes out of the ground. When fully equipped, the establishment will employ from thirty to forty men. ” The following issue of the Journal, February 27, reported that “R.A. Cook’s new foundry and machine shops has been christened the Central City Iron Works. ” Six months later, the whole manufacturing complex was finished, the August 13, 1892, Journal announced, devoting an entire column to details about it. “The main building, which rests on a stone foundation, is of red brick and The enlarged, remodeled Central City Iron Works building as depicted in an idealized postcard picture made sometime before 1919. Page 31 of 46 is 212 feet long and 40 feet wide, the walls being 14 feet high. The roof is of the Howe truss pattern, the timbers being very heavy. The roof is covered with asbestos roofing, as well as all the smaller buildings. The office, which is located on the west end of Madison street, is 16 feet square and is neatly fitted up. The main building is divided into a foundry, blacksmith shop and machine shop…. The boiler house on the east side is 20 x 30 feet and contains a bran new 80-horse power tubular steel boiler, made by the Pennsylvania Boiler Works, Erie, Pa. The smokestack is 9 feet square at the base, has a 36-inch flue and extends skyward 75 feet. East of the building is a shed 24 x 80 feet, partitioned off for coal, iron, &c…. The pattern storehouse, a brick fire-proof building 24 x 40 feet, is located just west of the office…. Every pattern will be numbered and any casting can be duplicated at any time. The foundry is supplied with a new Calliau cupola, with a guaranteed capacity of seven ton per hour for four consecutive hours. The cupola is 40 feet high and 60 inches in diameter, near which is an elevator with a capacity of seven tons, to be used in hoisting the iron and coal to the platform. The blast for the furnace is furnished by a No. 9 steel pressure blower…. The wood working shop will be supplied with lathes, band saws, &c., for doing all kinds of wood turning and other wood work…. A track will run through the entire length of the foundry, on which the melted iron can be carried and deposited on either side. This track will also extend into the coal and pig iron warehouse…. The shop presents a handsome appearance from the outside and being supplied with 33 large windows is well lighted and makes a very pleasant place to work. The brick work on the building was done by Ule Bros., the carpenter work by Chas. Packard and the painting by Krembs Bros. The brick was furnished by the Stevens Point Brick Co…. At present 22 hands are employed, but it will require from thirty to forty hands to do the work when all departments are under full headway…. ” In the following summer, the July 15, 1893, Journal, in yet another long article on the Central City Iron Works, listed the products the firm had made for various companies around the state, since it had opened. “ Among the work recently turned out by this establishment was a lot of shafting, gearing and pulleys for the Ellingson mill of Stetsonville, Wis.; a new granulator and a clay dumping car for Wm. Langenburg & Son’s brick yard….; repairing of an engine for the Chilli Lumber Co., of Chilli, Wis.; the truss rods and roof irons and the cast iron work for the Plover Paper Co. ’s mill; the shafting, pulleys, gearing boxes, etc., for Gilkey Anson & Co. ’s saw mill at Merrill; repairs for locomotive, new brasses, etc. for J.J. Kennedy of Rib Lake; a 40 horse power boiler, fronts, grates, stacks and fixtures, for Whitney & Wells’ mill on the Plover river; repairing of Bosworth & Reilly’s gang edgers, and new braces for the engine, doors and plates for the charcoal kilns of the Wisconsin Furnace Co. on the line of the Central railroad. Also manufactured several set[s] of of the Wendt patent automatic car couplers, of which there is 10 refrigerator cars on the Wisconsin Central line equipped. A pair of these couplers are mounted and on exhibition in the transportation building at the World’s fair. These works also furnish the castings for the Marshfield Iron Works, and are filling a large order for the new paper and pulp plant at Nekoosa, Wis., which consists of about 115 tons of wrought iron truss rods, bolts, plates, anchors, cast iron columns, lintels, caps, plates and washers. Ten years ago, Mr. Cook built the North Side Lumber Co. ’s 75 horse power engine, and it is still in good running order…. ” Cook’s company operated through the 1890s and the first decade of the 20th century, increasing its business steadily. At one point, in 1909, a consortium of Stevens Point businessmen leased the Central City Iron Works plant, according to the Gazette of May 26, but apparently the firm continued to be called by its old name. At least the 1908, 1912, 1915-16, and 1920 city directories listed the company by the name of Central City Iron Works, and gave R.A. Cook as its proprietor. In 1913, the company entered into a contract with the Soo Line Railroad, to furnish all its gray iron castings, a change constituting a big boost in the firm’s volume of business, the March 8 Journal reported. Interestingly, the Central City Iron Works indirectly participated in World War I. According to the April 7, 1917, Journal, “More war munitions manufacture is to be carried on in Stevens Point this season, at least indirectly. The Central City Iron Works has received a contract for building two large Wagner looms with trimmers for the Burlington Blanket Co. of Burlington, Wis. These are 57 and 80 inch machines and are designed to turn out blankets, horse collar pads and other articles. They are intended for use in the Canadian factory of the company and it is understood they will be used in making blankets and other supplies for the Canadian and British armies in Europe…. ” Page 32 of 46 The remains of the Trenam Tractor Company building at 2041 Madison Street in Stevens Point now. The former Altenburg Ice Cream Shop occupied the small part at the far right—once upon a time R.A. Cook’s Central City Iron Works office--in the 1990s. Note that the remains of the company’s name are still visible at the top of the building: “...ctor Co. The Trenam Tractor Company After America entered World War I, the Central City Iron Works was making a more direct contribution to the war effort, but that was after it was acquired by the Trenam Tractor Company. The Gazette of December 26, 1917, reported that “Stevens Point is to be the home of the Trenam Tractor Co. This announcement, which had been expected for several weeks, was made [on December 20], following the closing of a deal for the purchase by the company of the land, buildings and equipment of the Central City Iron Works on Madison street. Possession was taken Friday morning [December 21]. “ Although the plant was purchased …for the manufacture of Trenam tractors…the general foundry business will be continued and enlarged. Ralph Cook [son of R.A.] is acting superintendent of the plant and F.M. Schuler of Milwaukee acting manager, the latter being secretary and treasurer of the company. The crew of twelve or fifteen is retained. “The Trenam Tractor Co. comes to Stevens Point without a bonus of any kind, but a sufficient amount of stock was disposed of locally to purchase the plant. R.A. Cook, proprietor of the Central City Iron Works, has a financial interest in the company. G.A. Gullickson of this city, who became interested in the tractor at the time it was in the blue print stage and who is now one of the directors, was largely responsible for bringing the concern here…. “The patterns of the company are all complete and will be shipped here from Ludington, Mich., and Milwaukee within the next week. Some changes must be made in the plant and new equipment installed, but it is hoped to begin casting for the tractors within the next couple of weeks. An inventory is now being taken at the plant. “The officers of the company do not intend to rush things, but to start in a conservative way to ensure a healthy growth. Their goal is to have the first machine of local manufacture ready by April 1 and to be able thereafter to turn out the finished tractors at the rate of five a day. The machine will be handled through dealers and the fact that she sales will Page 33 of 46 be on a cash basis will enable them to get quick returns. “By the middle of the summer, it is hoped, from forty to fifty men will be employed. It is believed also that it will be necessary to erect another building during the coming season. If the business develops as expected, it is not improbable that 300 men will be employed inside of two years. “The company now has five machines on hand, which have been put to the hardest kind of tests under actual field conditions, with complete success. The Trenam is a farm tractor of many uses and [develops] 12-24 horse power. It is an ‘all-purpose’ tractor, serving as a power unit as well as a substitute for horse power. It is light in weight, well balanced and mechanically a wonder, according to recognized authorities. The fact that there is an ever growing field for tractors, makes the manufacture of the Trenam a most attractive proposition…. “ All of the directors are heavily interested financially. The concern is incorporated under the laws of South Dakota and has an authorized capital of $400,000, of which $300,000 is common stock and $100,000 preferred. ” True to its word, the tractor company did continue to do general foundry and machine-shop work. So its ad announced in the January 16, 1918, Gazette: Foundry and Machine Work Having taken over the Central City Iron Works, we have the facilities for giving prompt and first- class service in all kinds of Foundry and Machine work. We solicit your patronage and guarantee satisfaction. TRENAM TRACTOR COMPANY SOUTH SIDE Also, according to the May 15, 1918, Gazette, the plant began a more direct involvement in war work. “STEVENS POINT FIRM GETS WAR CONTRACT…. Grey iron castings, engine parts for coast defense boats, are now being manufactured in Stevens Point by the Trenam Tractor Co., which took over the plant of the Central City Iron Works last fall. “The local concern is turning out the castings for the Allis Chalmers Co. of West Allis, which has for many months been utilizing its immense plant for war work. The volume of war work being sent here is increasing and it is expected that within a short time casting will be done daily. Twenty men are now employed…. ” But, otherwise, the tractor company signally failed to live up to its promised success. Contrary to its glowing predictions, it went bankrupt only a year later, and made only one demonstrator tractor, according to the October 12, 1966, Daily Journal. “In 1919, the company lost its license to do business in Wisconsin for failing to file an annual report. ” An intensive search of the local newspapers from 1919 through 1921 has failed to corroborate these statements. Other evidence has surfaced that the company did not meet its stated expectations. For example, an article in the May 7, 1920, Journal, reporting on a meeting of the Trenam Tractor Company’s board of directors, conceded that the firm was making no tractors at that time. “While the Trenam Tractor plant in this city is not now engaged in the manufacture of tractors, as changes and improvements in the machine room are being made by the draftsmen, both the local foundry and machine shop are being run full time…. ” Further evidence—albeit circumstantial--is an ad in the Stevens Point Gazette of November 9, 1920: “FOR SALE To the highest bidder 100 Shares Trenam Tractor Stock. Write J.S. CUDLIPP 1834 Main St. BUFFALO, N.Y. ” This ad does not prove the company was going bankrupt, but it does appear that at least one stockholder was trying to jump from the ship before it sank. And was it only a coincidence that at virtually the same time as the Trenam Tractor Company was failing, a new tractor factory sprang up in Stevens Point? That is what readers of the Gazette of November 9 and 16, 1920, were told. An ad in the issue of November 9 announced a “TRACTOR DEMONSTRATION at the R.K. McDONALD FARM west side THURSDAY, NOV. 11 2 P .M. By the FARMERS’ TRACTOR CORP . New Industry Located Here. ” In a full-page ad in the November 16 Gazette, the new company announced a capitalization of $500,000, with preferred stock offered for sale at $100.00 per share, “with a bonus of one share of the common stock…. The citizens of Stevens Point and vicinity can easily …hasten the day of early manufacture and returns. INVEST TODAY. ” But the ad was vague about much important information, including where exactly in the city the tractors would be made. After the Trenam Tractor Company went bankrupt and into receivership, two new firms set up business successively in the building. The first was a carton- or box-making factory, the Wisconsin Carton Company, which was announced in the March 22, 1929, Daily Journal. This company secured a three-year lease on the former tractor-factory building, and, the May 8 issue reported, laid a new concrete floor in part of the facility. Page 34 of 46 Ten years later, “The Vaudell Wholesale Food company, a new concern, has located in Stevens Point and is occupying quarters in part of the Trenam Tractor company building at 319 Madison street, ” the June 20, 1939, Daily Journal reported. But neither of these companies apparently lasted very long. Meanwhile, the progressive decline of Trenam Tractor Company building came in two or three fires that damaged the structure that was the company’s only remaining asset. The last fire was in 1959, the Daily Journal of February 12 reported. Then the building was used mostly as a warehouse, and was rented by various local companies for storage. But it burned extensively, and part of the second floor collapsed onto the first floor. Not until 1968 did the stockholders from 1918, or their descendants, get back the money they had invested in Trenam Tractor, and then only pennies on the dollar, reported the February 15, 1968, Daily Journal. It was an anticlimax from the optimistic buildup 50 years earlier, especially for one investor, who was killed in a car accident in Florida just as she was to receive her settlement check. The Trenam Tractor Company building—or part of it—still stands on the south side of Madison Street, with some of the letters of its name still visible on its red-brick façade. That is, also, part of R.A. Cook’s Central City Iron Works building still stands, for they are or were the same building. And what was Richard Cook’s office, in the small west section of the building, was in the 1990s the Altenburg Dairy Ice Cream Shop. All is deserted and quiet now, belying the busy hum and clank and thud of heavy machinery of a century ago, when massive machines made parts for train engines, sawmills, bridges, and buildings five stories high. Richard A. Cook (1850-1926) was born in England. He was part-owner of the Pinery Iron Works and the R.A. Cook & Company firm, and sole owner of the Central City Iron Works. Delia Damp Cook (1854-1938) was Richard .A. Cook’s second wife. Page 35 of 46 The Life of Richard Cook In its general outlines—because we know little of its details—the life of Richard A. Cook of Stevens Point would seem to have been the quintessential rags-to-riches success story of American folklore. He began life humbly, and ended it in at least local prominence and wealth. According to his obituary in the March 5, 1926, Stevens Point Daily Journal, Cook was born in Netherton, Yorkshire, England, in 1850. When he was five years old, he emigrated with his parents and young sister to America, “the ocean trip being made in s sailing vessel which required 13 weeks and three days to cover the distance between Liverpool and New York. ” Unfortunately, his sister died during the voyage. Cook’s obituary says his family settled in Burlington, Wisconsin, when they arrived in America, and remained there twelve years. Then they moved to Fond du Lac, where young Richard began learning the machinist’s trade “in the Trowbridge shop. ” Afterwards, he worked for the Northwestern Railroad Company as a machinist. According to his obituary, Cook had, besides his business in Stevens Point, investments in “a veneer plant at Glidden [Wisconsin] and also was part owner of extensive timber properties in northern Minnesota. ” Cook was also active in the social and civic life of the city. He was a 32nd Degree Mason, and was the “treasurer of the local bodies. ” “Mr. Cook was also prominently identified with the congregation of the Church of the Intercession, serving successively as vestryman, junior and senior warden…. In civic affairs the deceased did his full share. He served as alderman for a number of years and also represented the Second Ward on the local board of education, in which latter body he filled the office of president for a longer period than any other local resident. ” Despite his material success, Richard Cook, like most people, experienced his share of life’s pain and losses. Besides his sister’s early death, his father died while he, the son, was still living in Fond du Lac, according to his mother’s obituary in the Stevens Point Journal of October 30, 1895. (His parents apparently had two more children after they came to the United States, one of whom also was a resident of Stevens Point: Etta—Mrs. John—Shaffer.) Also, Richard Cook’s only child, a boy, died at the age of two months, the June 14, 1884, Journal reported. And four years later, Cook’s first wife, Eliza, died of consumption—tuberculosis—at the age of 37, according to the October 6, 1888, Journal. Her maiden name was Trowbridge; was she related to her husband’s first employer? She was a teacher before she married R.A. Cook, her obituary noted, and they were married in 1882, the same year their fine, red-brick Italianate house at 1532 Church Street was built. In 1890, Richard Cook remarried. His new bride was Delia Damp, also a teacher before she married Cook. She grew up on farms near Juneau, Pardeeville, and Lowell, and eventually moved to Portage, Wisconsin, with her parents, where she graduated from high school. She also studied teaching for a year at the Oshkosh Normal School in 1875, before moving to Stevens Point to teach, according to her obituary in the April 6, 1939, Daily Journal. However, after teaching here for a few years, she left to teach at Oshkosh and Medford for three years each before returning to Stevens Point permanently and marrying R.A. Cook. Delia Cook was active in many social organizations, her obituary says, including playing-card groups, church groups, and Progress Club, a literary society. Also, “Instrumental in the establishment of a public library in Stevens Point, Mrs. Cook was elected to the board in 1898 and was chosen as its secretary at the first meeting…. She was… president of the board for many years. ” The late Marjorie Warner, director of the first Charles M. White Memorial Public Library, recalled that when Delia Cook was president of the Stevens Point Library Board, she, Mrs. Cook, would wear white gloves into the then- Carnegie Public Library. If she saw dust on the windows, she would write with her white-gloved finger in the dust, “Delia D. Cook, Delia D. Cook” in big script, so that everyone would notice it. And the next time she came into the library, the windows were clean. R.A. and the second Mrs. Cook had one child, a son, Ralph. According to his obituary in the Journal of May 21, 1983, Ralph graduated from high school in 1912, and attended the Stevens Point Normal School. He served in the U.S. Army during World War I, and during World War II “was a government inspector in defense plants. ” He worked for his father’s Central City Iron Works and the Trenam Tractor Company, as well as the Consolidated Paper Company. He also sold Buick cars and GM trucks in Stevens Point, and was City Assessor from 1953-1960, his obituary says. ©2014 Wendell R. Nelson Page 36 of 46 Page 37 of 46 Page 38 of 46 Page 39 of 46 Page 40 of 46 Page 41 of 46 Page 42 of 46 Page 43 of 46 Page 44 of 46 PROPERTY RECORD 1039 ELLIS ST Architecture and History Inventory NAMES Historic Name: Other Name: Weber Manufacturing Co. Contributing: Reference Number: 73271 PROPERTY LOCATION Location (Address): 1039 ELLIS ST County: Portage City: Stevens Point Township/Village: Unincorporated Community: Town: Range: Direction: Section: Quarter Section: Quarter/Quarter Section: PROPERTY FEATURES Year Built: 1928 Additions: Survey Date: 2011 Historic Use: large office building Architectural Style: Commercial Vernacular Structural System: Wall Material: Stucco Architect: Oth B ildi O Sit Page 45 of 46 Other Buildings On Site: Demolished?: No Demolished Date: NATIONAL AND STATE REGISTER OF HISTORIC PLACES National/State Register Listing Name: Not listed National Register Listing Date: State Register Listing Date: NOTES Additional Information: THIS WAS ORIGINALLY A BRICK-CLAD INDUSTRIAL BUILDING THAT THE ASSESSOR'S RECORDS SAY WAS BUILT IN 1928. SINCE THEN, HOWEVER, IT HAS BEEN COMPLETELY REMODELLED INTO OFFICE SPACE, THE EXTERIOR HAS A CONTEMPORARY STYLE DESIGN AND IS CLAD IN STUCCO PANELS, AND THE BUILDING NO LONGER RETAINS ITS HISTORIC APPEARANCE. Bibliographic References: CITY OF STEVENS POINT ASSESSOR'S RECORDS. RECORD LOCATION Wisconsin Architecture and History Inventory, State Historic Preservation Office, Wisconsin Historical Society, Madison, Wisconsin Have Questions? If you didn't find the record you were looking for, or have other questions about historic preservation, please email us and we can help: leah.penzkover@wisconsinhistory.org If you have an update, correction, or addition to a record, please include this in your message: AHI number Information to be added or changed Source information Note: When providing a historical fact, such as the story of a historic event or the name of an architect, be sure to list your sources. We will only create or update a property record if we can verify a submission is factual and accurate. Page 46 of 46

Source: City of Stevens Point website. First collected Oct 30, 2026.