RecordWell Data

Ad Hoc Advisory Committee on Industrial Livestock Operations — Agenda Packet

Portage County · Portage County · Land and Water Conservation Committee · meeting of Nov 5, 2025 · Agenda packets

Open the original document More from Portage County

Text

Extracted automatically from the original. Tables and formatting may not survive; the original document is authoritative.

PORTAGE COUNTY MEETING AGENDA AD HOC ADVISORY COMMITTEE ON INDUSTRIAL LIVESTOCK OPERATIONS PORTAGE COUNTY ANNEX CONFERENCE ROOMS 1 & 2 1462 STRONGS AVENUE STEVENS POINT, WI 54481 Wednesday, November 5, 2025 7:00 PM REMOTE ATTENDANCE & COMMENT To attend this meeting by telephone : dial 1-872-242-7813, after dialing the number you will then be asked to enter in a meeting number. Use the following meeting number: 846 062 856, then press # To attend this meeting by video: Join the meeting now Page 1 of 2 CALL TO ORDER CORRESPONDENCE PRESENTATIONS 1. Nathan Check, Portage County Highway Commissioner — Overview of road damage from farm equipment REPORTS 2. Special Meeting Attendance Reports (Portage County Ordinance 3.1.47 & 3.1.48) PUBLIC NOTICE Members of the public who wish to address the Committee on specific agenda items must register their request at this time, with such comments subject to the public comment ordinance and the reasonable control of the Committee Chair as set forth in Robert’s Rules of Order. APPROVAL OF MINUTES 3. Approval of October 29th, 2025 Meeting Minutes DISCUSSION/POSSIBLE ACTION 4. Discussion/Possible Action Re: Environmental impact recommendations as they relate to proposed industrial livestock operations ordinance 5. Discussion/Possible Action Re: Recommendations regarding roads as they relate to proposed industrial livestock operations ordinance 6. Discussion/Possible Action Re: Recommendations on financial assurance as they relate to proposed industrial livestock operations ordinance 7. Discussion/Possible Action: Review of Schedule of Future Agenda and Committee Recommendations NEXT MEETING DATE November 19th, 2025. ADJOURNMENT Notice: Any person who has special needs and plans on attending this meeting in-person or remotely should contact the Facilities Office at 715-346-1598 as soon as possible to ensure that reasonable accommodations can be made. Notice: Remote comment by the public during the meeting will be at the discretion of the Chair. Page 1 of 19 Ad Hoc Advisory Committee on Industrial Livestock Operations Meeting Agenda November 5, 2025 Page 2 of 2 Notice: A quorum of the Portage County Board of Supervisors, or any committee thereof, may be present at this meeting. Page 2 of 19 County Engineer – Lucas Meddaugh County Patrol Manager – Kory Kukuczka State Patrol Manager – David Johnson Parts Room / Shop Manager – Corey Giese Assistant Patrol Manager – Bob Lang /uni0046inance /uni004F/g431ice Supervisor – Stacy Zerby /uni0046inancial Associate III – Kristen Hancock Portage County Highway Department Nathan Check, PE Commissioner 800 Plover Road Plover, WI 54467 Phone: 715-345-5355 Fax:715 -345 -5356 Date: October 22, 2025 To: Amberle Schwartz, Chairperson for Ad Hoc Advisory Committee on Industrial Livestock Operations From: Nathan Check, P.E. Subject: Portage County Ad Hoc Advisory Committee on Industrial Livestock Operations – Road Regulations Dear Chair Schwartz, Thank you for reaching out to me regarding the County’s Ad Hoc Advisory Committee on Industrial Livestock Operations and questions regarding the potential role of the Committee and draft ordinance in regards to regulating roadway use. I appreciate the Committee’s consideration of our important and valuable infrastructure resources, but the Committee may want to review the information below prior to including any additional regulations within the Operations ordinance in regard to roadway use. 1. Current Authority to Protect Local Roads Wisconsin Statute Chapter 348 provides for the general maximum weight restrictions for vehicles on state, county, and local roads. https://docs.legis.wisconsin.gov/statutes/statutes/348.pdf State, county, and local officials are also granted powers under Chapter 349 of the Wis Stats which allow them to designate all or a portion of their road way systems as Class B Highways.( https://docs.legis.wisconsin.gov/statutes/statutes/349.pdf ). The Class B designation reduces the permitted weight, year-round, not to exceed 60% of the legal load limits. It takes effect when signs are posted and remains in effect until the signs are removed. The statute does provide from some exemptions for the Class B classification which include: local pick-up and delivery of legal loads, waste haulers at legal load, and Class B Implements of Husbandry.(IoH). More information regarding IOH’s is below. In addition, the statute allows county and local officials to post certain roads and bridges with reduced load limits as an alternative to protecting the infrastructure which may be not built to withstand heavy loads. These postings may be year-round or seasonal. Page 3 of 19 County Engineer – Lucas Meddaugh County Patrol Manager – Kory Kukuczka State Patrol Manager – David Johnson Parts Room / Shop Manager – Corey Giese Assistant Patrol Manager – Bob Lang /uni0046inance /uni004F/g431ice Supervisor – Stacy Zerby /uni0046inancial Associate III – Kristen Hancock Portage County Highway Department Nathan Check, PE Commissioner 800 Plover Road Plover, WI 54467 Phone: 715-345-5355 Fax:715 -345 -5356 While the attached Transportation Bulletin No. 8: Using Weight Limits to Protect Local Roads is from 2003, it includes a very good summary of the statutes and abilities for the local forms of government to protect their local roads. Another factor to consider is that Wis Stat 349.15 and 349.16 are very specific on who has the authority to impose these restrictions as “the loca l authority in charge of maintenance”. The Committee would need to check with Corporation Counsel if any town road regulation within the ordinance is enforceable or even allowed by statute since the County is not the maintaining authority for town roads. 2. Regulation of IoH’s Significant changes were made to Wis Stat Chapter 348 approximately 10 years ago to provide for additional clarification on definitions, weight and size restrictions, and regulation authority for IoH’s and agricultural commercial motor vehicles(AgCMV). Additional information can be found at: https://wisconsindot.gov/Pages/dmv/agri-eq-veh/default.aspx . The definition of IoH is: A self-propelled or towed vehicle manufactured, designed, or reconstructed to be used and that is exclusively used in the conduct of agriculture. An implement of husbandry may also include any of the following: • A farm tractor (referred to as Category A); • A self-propelled combine; a self-propelled forage harvester; self-propelled fertilizer or pesticide application equipment but not including manure application equipment, towed tillage, planting, and cultivation equipment and its towing power unit; or another self- propelled vehicle that directly engages in harvesting farm products, directly applies fertilizer, spray, or seeds but not manure, or distributes feed to livestock (referred to as Category B); • A farm wagon, farm trailer, manure trailer, or trailer adapted to be towed by or to tow or pull, another implement of husbandry (referred to as Category C). An AgCMV is also defined as: An Ag CMV is a commercial motor vehicle to which all of the following apply: • Substantially designed or equipped, or materially altered from its original construction, for the purpose of agricultural use • Designed and manufactured primarily for highway use • Manufactured to meet federal motor vehicle safety standard certification label requirements 49 CFR 567, after 1970 • Used exclusively in the conduct of agricultural operations Page 4 of 19 County Engineer – Lucas Meddaugh County Patrol Manager – Kory Kukuczka State Patrol Manager – David Johnson Parts Room / Shop Manager – Corey Giese Assistant Patrol Manager – Bob Lang /uni0046inance /uni004F/g431ice Supervisor – Stacy Zerby /uni0046inancial Associate III – Kristen Hancock Portage County Highway Department Nathan Check, PE Commissioner 800 Plover Road Plover, WI 54467 Phone: 715-345-5355 Fax:715 -345 -5356 • Directly engaged in harvesting farm products, directly applies fertilizer (including manure), spray or seeds to a farm field, or distributes feed to livestock The statute sets the weight limit for all IoH and Ag-CMVs is 15% higher than the federal bridge formula. This equates to a maximum single axle weight of 23,000 pounds and maximum gross vehicle weight (GVW) of 92,000 pounds, dependent on axle number and spacing as presented in the IoH/Ag CMV Maximum Weight Limits table (s. 348.15 3g). It also provides for exemptions for Category B IoH’s and empty potato harvesters from the axle weight limits but they shall adhere to the maximum gross vehicle weights. Even with the law changes, local authorities still have ability to issue permits and post roads and bridges as they have under prior law. Regardless of the exemptions, the statute requires all IoH’s, including Category B’s to obey seasonal or special road and bridge postings. Local governments also have a range of choices to implement the IoH/Ag CMV laws which also include a uniform no-fee permit application. All other maintaining authorities are required to participate in the permitting process but they have options in regards to regulating IoH’s by ordinance. The Local governments options include: • Pass no ordinance or resolution if the local government chooses to allow the statutory weight and length limits and exemptions to Category B IoH from axle limits on roads under their jurisdiction. Permits may be issued to operate IoH and Ag CMVs that exceed statutory limits on local roads. • Pass Resolutions or ordinances if the local government chooses to: o Opt In - Which requires all IoH (including Category B) and Ag CMVs to follow the new IoH/Ag CMV Maximum Weight Limits for both Gross Vehicle Weight (GVW) and Axle Weight. Permits may be issued to operate IoH and Ag CMVs that exceed statutorial limits on local roads. o Total Opt Out - Have no weight or length limits for IoH and Ag CMVs operating on roads under their jurisdiction. A permit is not needed. o Partially Opt Out I – Set weight and length limits above those set for th in statute for IoH and Ag CMVs operating on all roads under their jurisdiction. A permit may be necessary. o Partially Opt Out II - Designate specific roads under their jurisdiction for over- weight/over-length IoH and Ag- CMV travel. Page 5 of 19 County Engineer – Lucas Meddaugh County Patrol Manager – Kory Kukuczka State Patrol Manager – David Johnson Parts Room / Shop Manager – Corey Giese Assistant Patrol Manager – Bob Lang /uni0046inance /uni004F/g431ice Supervisor – Stacy Zerby /uni0046inancial Associate III – Kristen Hancock Portage County Highway Department Nathan Check, PE Commissioner 800 Plover Road Plover, WI 54467 Phone: 715-345-5355 Fax:715 -345 -5356 • Post roads or bridges , regardless of passing an ordinance or resolution. All vehicle operators, except those with statutory exemption, are responsible for following seasonal and special postings and any postings on highway roads, bridges or culverts. Ordinances or resolutions must be passed by November 30 of each calendar year and each municipality. Additional information and be found at: https://wisconsindot.gov/Pages/dmv/agri- eq-veh/local-govt-info.aspx which includes links to all of the local municipal ordinances. For Portage County roads, the County Board did not pass a resolution and as a result, county roads follow the statutory limits and permit requirements. Portage County towns have ranged in their decisions which are summarized below: -Total Opt In – Towns of Dewey and Hull -Partial Opt Out – Town of Grant -Total Opt Out – Towns of Buena Vista, Almond, Belmont, and Amherst -Follow Statutory Limits and Permit requirements – remaining towns As you can see, there are major differences on how local towns within the county decided to handle the regulation and permitting of IoH’s within their respective towns. Due to these differences and the fact that local towns have the authority to post special weight limits, I believe it would be difficult to draft a county-wide ordinance for every local road. Enforcement Since the Operations ordinance would only pertain to certain large-scale animal farming operations, any special road ordinances may be difficult to enforce considering the large amount of other agriculture operations within the county. It would be difficult for law enforcement to discern if a certain IoH is operating for a large-scale animal operation that is governed by the ordinance or if it was for another type of farm such as a grain cash crop operation that is not covered under the ordinance. The Committee may want to consider discussing enforcement options with the Sheriff’s Office as their current staffing levels may be strained and weight enforcement will include additional training and resources such as portable axle scales. Prosecution Enforcement may only be effective if there is follow through with prosecution. The Committee may also want to consider discussing prosecution of the overweight fines with the District Attorney’s Office as well. Page 6 of 19 County Engineer – Lucas Meddaugh County Patrol Manager – Kory Kukuczka State Patrol Manager – David Johnson Parts Room / Shop Manager – Corey Giese Assistant Patrol Manager – Bob Lang /uni0046inance /uni004F/g431ice Supervisor – Stacy Zerby /uni0046inancial Associate III – Kristen Hancock Portage County Highway Department Nathan Check, PE Commissioner 800 Plover Road Plover, WI 54467 Phone: 715-345-5355 Fax:715 -345 -5356 Summary Ultimately, Wis Statutes provide the local maintaining authorities to provide for additional restrictions to protect their road and bridge infrastructure. These local officials are required by statute to conduct road ratings and reviews every two years and can address any issues within their current statutory authority. While the Committee’s consideration is appreciated, I think it may be difficult to place county- wide regulation and oversight on the 1,300+ miles of local roads through a County-wide ordinance specific to certain operations. Corporation counsel should be contacted to verify if a county-wide ordinance regulating weights on local roads is allowed and enforceable by statute. The Sheriff’s Office would also likely be the enforcing authority and should be brought into the discussion. Since enforcement is likely a point-in-time scenario, overweight loads would have to be “caught in the act.” Based on current staffing and other priorities, this may be difficult. If you have any additional questions, please do not hesitate to contact me. The purpose of the memo was to provide additional information prior to the November Committee meeting so that the appropriate question and answers can be presented to the Committee. Once you have reviewed all of the information, please contact me to discuss the specific points that you would like to focus on for the Committee discussion. We could spend hours on the IoH discussion alone, but that statute applies to all agriculture operations, not just larger farms that may be covered under the new ordinance. Thank you. Attachments: Transportation Bulletin No. 8: Using Weight Limits to Protect Local Roads Page 7 of 19 Wisconsin’s extensive local road system is a lifeline for our state and local economies. Farms and businesses depend heavily on these roads to move manufactured, forest and agricultural products. Highway and street agencies need them to economically transport road- building materials. The public also relies on truck trans- portation to receive goods at reasonable prices. However, heavy truck loads can damage local road pavements, especially in spring when they are weakened because they are saturated with water. Local officials have a responsibility to preserve our investment in roads by protecting them from excess damage caused by trucks carrying heavy loads. They have the authority to restrict truck weights under state statutes. However, local officials must carefully balance the public good in protecting roads against the legitimate need for efficient transportation. We can’t do anything to control the weather, but we can regulate how much weight is carried on certain roads, especially during spring thaw. According to a national study by the Federal Highway Administration (FHWA), reducing truck weights by just 20% between late February and early May can increase the life of vul- nerable pavements by 62%. Cutting weights in half increases pavement life by 95%. To be most effective, truck weight control programs should be coordinated with the Wisconsin Department of Transportation, adjoining local road agencies, the trucking industry, and the public. This bulletin describes the causes of spring weakness in roads, how heavy loads do damage, and the charac- teristics of vulnerable roads. Techniques are introduced for determining which roads need protection in spring and when roads are vulnerable, along with guidelines on how to set weight limits. Year round restriction on roads and bridges is also discussed briefly. Another Wisconsin Transportation Information Bulletin, HowTVehicleTLoads AffectTPavementTPerformance,T No.To,Tdiscusses in more detail how heavy trucks damage pavements. How freezing affects pavements A road’s design is based on a reasonable estimate of the average loads it will carry during its projected life. That is why Interstate highways carrying thousands of trucks a day have thick concrete pavements while rural roads, built for local traffic and a few trucks, are often a few inches of compacted gravel or asphalt laid on a shallow base. Soil types and local drainage characteristics also affect design and load capacity. To build roads, designers use calculations based on strength and moisture tests of the natural soil or subgrade. The road base and surface depth are then designed for the average condition. Roads can be designed for the worst soil conditions but the cost is usually not justified by the expected use. When the weather gets cold, pavements and the water trapped within them freeze near the surface. As cold temperatures persist and go lower, the frost line moves deeper into the soil. Frost depth may range from relatively minor—one or two feet during mild winters in southern Wisconsin—to extremes of five to eight feet during severe winters in the northern part of the state. Using Weight Limits to Protect Local Roads WisconsinrTransportationrBulletinr•rNo.r8 1 Asrspringrthawrweakensrpavements,rtrucksrcarryingrheavyrloads canrdamagerthem. Page 8 of 19 Frostractionrandrfrostrheaves Pavements can be severely damaged in winter by frost heaves from water freezing in the soil. Damage can be particularly bad when the heaving is greater in one pavement section than another or when it occurs next to structures that don’t move, like bridges or manholes. There are three critical factors in frost heave: freezing temperatures, a source of water, and susceptible soils. Frost heave results not just from the natural expansion of water as it freezes, but from the buildup of a series of ice layers, called lenses, that form at the freezing front as it penetrates downward. This can cause heaves of a few inches to several feet. Water comes from the normal water table. Problems are more severe when the water table is near the pave- ment surface, but significant frost heaving can occur even when it is many feet below the actual frost depth. Frost-susceptible soils are fine-grained like silt and clay. These permit water to move from the water table to the freezing front through capillary action. Silt is usually the worst because it has enough capillary action to move water and its pore spaces are big enough to transmit large amounts of water. Granular soils like sand have relatively large pore spaces which generally do not have sufficient capillary action to be frost susceptible. Springrthaw In spring, roads begin to thaw from both the top and bot- tom. As ice in the pavement melts, water saturates the road’s base and subgrade. These layers lose strength, like a handful of mud compared to dry soil. As thawing con- tinues, melt water becomes trapped in the upper sub- grade, unable to drain away through the frozen soils below. Pavements weaken considerably in a very short time under these conditions. The weakness can continue for weeks or months after the pavement is completely thawed. It takes a long time for water to leave the pavement because frost-susceptible silt and clay soils are relatively slow to drain. How heavy vehicles damage roads Without adequate support, a pavement or gravel surface deflects too much under trucks carrying heavy loads, developing cracks or ruts. These then let more moisture penetrate, worsening the cycle until the road fails completely. The amount of damage a road sustains is directly related to the weight of the load and how often it is applied, according to tests by AASHTO (the American Association of State Highway and Transporta- tion Officials). Passenger autos and light duty vehicles are not a problem. It is trucks carrying legal weight loads of up to 80,000 GVW over weakened surfaces which do the damage. When trucks carry loads that are heavier than the statutory weight limit, the potential for damage is much higher. Another factor is the amount of weight and number of tires on each axle. Damage increases rapidly with higher axle loads and actually worsens at a faster rate than the load increases. A nine-ton axle load, for example, causes about ten times more damage than a five-ton axle load. Distributing a vehicle’s weight and its payload over more axles and tires makes the load lighter at each point of contact, reducing damage to the road. However, low-inflation tires do not protect roads from damage. It has been commonly assumed that large loads carried by off road equipment would have little adverse affect because they have flotation tires or treads that allow them to work in soft soils. In actual field tests, the South Dakota DOT showed that off road equipment with axle loads that exceeded legal limits caused damage to asphalt, sealcoat, and gravel roads and shortened pavement life. Imposing restrictions on truck weight limits is a reasonable and practical way to protect vulnerable local roads when they are at their weakest. Spring weight limits should begin with the first thawing and continue until the pavement is again strong enough to carry normal loads. 2 WINTER SPRING SUMMER FALL STRENGTH Restrict Load Variationrinrpavementrstrengthrthroughoutrtheryear. Page 9 of 19 Choosing roads for spring weight restrictions Consider the following factors in deciding which roads or segments should have restrictions. •PavementTthicknessTAsphalt surfaces of two inches or less, or total pavement less than 12 inches thick. •TypeTofTsubgradeFine-grained subgrade soils, like silts and clays, and areas with a high water table and poor drainage. •PastTexperienceAreas with alligator cracking or rutting that break up every year and need frequent patching and repair. •AmountTandTtypeTofTtruckTtrafficConsider all truck traffic and especially seasonally higher volumes of trucks carrying heavy loads. •SurfaceTdeflectionTPavement sections where the surface deflects or bends 50% more during spring thaw than in summer. Also, increased deflection lower than 50% on weaker pavements where summer deflections are relatively high. •PavementTage/conditionWeight restrictions can protect your investment in new pavements and prolong the life of weak or aging pavements. Year round restrictions — Class II and Class B roads All public roads are considered to be Class A unless des- ignated otherwise. Vehicle weight restrictions established in Chapter 348 are intended for travel on Class A high- ways. Some roads, designated Class II or Class B, have permanent weight restrictions, with some exceptions. The state may designate certain highways as Class II. These are limited to legal loads. No overloads are allowed, even when the hauler has an overload permit. About 1600 miles of state highway, mostly in the north and west, are Class II. State, county and local authorities may designate all or a portion of their systems as Class B highways under Sections 349.15 and 349.16, Wisconsin Statutes. This designation reduces the permitted weight, year round, not to exceed 60% of the legal load limits. It takes effect when signs are posted and remains in effect until the signs are removed. Two types of loads are exempted under Class B desig- nation. The rules now allow local pick-up and delivery of full legal loads. Also, waste haulers can haul their full legal load if, because of health concerns, the material must be removed from a septic or holding tank within 24 hours and if they minimize their travel on the weight- restricted roads. Class B highway designation, which in general is permanent, not seasonal, is intended for situations where the pavement cannot withstand normal, legal truck weights. Such roads may not have been constructed to adequately handle these loads, or they may be roads through low areas with poor supporting soils. The Class B designation is well understood by industry. It is a reasonable option for local authorities when they believe it is necessary to protect pavement. WisDOT recognizes this local authority through administrative code. For example TRANS 255.12(6) requires explicit written permission for movement on Class B local roads even if a state permit has been issued. Posting reduced load limits, such as a 24-ton limit, is an alternative for protecting roads in weak condition. Local officials may choose this option if the exemptions which were added in 2002 to Class B for local pickup and delivery are unacceptable. Some bridges may also need protection. Although their strength is not affected by freezing, bridges may be weakened by age. Load limits should be determined by a competent bridge inspector or consulting engineer. As with roads, local agencies have authority to post weight limits for bridges under Chapter 349 of the Wisconsin Statutes. In addition to a sign at the bridge, there must be an advance warning sign at the nearest intersection. Determining weight limit reductions Aweight reduction of just 20% during critical weeks in March and April can make a major difference in pave- ment life according to a study by the Federal Highway Administration. As weights are reduced further, potential pavement life increases even more. Local agencies have the authority to determine seasonal weight limits on their road systems. About 50% of the normal limit is typical, but establishing limits that are consistent with those set by the state DOT and adjoining agencies on nearby roads is strongly recom- mended. For state highways WisDOT normally uses a 3 Page 10 of 19 spring weight limit of six tons per single axle and 10 tons per tandem axle. To be effective, loads should be reduced at least 20%, while reduction over 60% may have little added benefit. Nationally, the average reduction is 44% which would lengthen pavement life by about 88%, according to study results. Consider other factors also, however. Thin or weak pavements may need significant reductions during spring thaw; small or even modest load reductions will not prevent damage. Since limits will be ineffective if local haulers do not cooperate with them, the most effective restrictions are reasonable and directly related to pavement damage. Otherrremedialractions Along with restricting load limits, consider other ways of protecting pavements. When haulers seek exemptions, consider including special requirements. For example, a load could be made in two smaller loads. The route could be modified so that pick-up or delivery is made at the start or end, or so that the route is traveled in a different direction. The goal is to minimize the length of travel and number of truck loads on weak road sections. Another common approach to exceptions is to require that deliveries be made at night or in the early morning when roads may be stronger due to overnight freezing. Be careful not to overuse this approach. If substantial subgrade thawing has started, a light frost in the pavement surface offers limited value. Physical changes can also help. For example, where pavements are shaded, you can increase exposure to sunlight by removing trees, billboards or other obstacles. Eliminate standing water in roadside ditches and fill pavement surface cracks to reduce the amount of water getting to the freezing zone. Improve drainage in the roadbed by removing frost susceptible soils. A three foot combined depth of pavement and replacement base will prevent substantial subgrade freezing in the coldest winter in 10, according to the 1993 AASHTO DesignTGuide. Install geosynthetics between the free water layer and the freezing zone. Optimal placement depth and whether multiple layers are needed remains to be determined, however. Geosynthetic reinforcements may also limit damage during spring thaw by helping bridge weak areas and limiting pave- ment spread. When to begin restrictions It can be difficult to determine when the thaw begins. In Wisconsin, it generally starts in early March and is complete by early May. According to 38 years of data from the Wisconsin Department of Transportation (WisDOT), the average date for legal load restrictions on some state highways is March 10. Posting usually begins between March 1–8 in the southern half of the state and March 12–18 in the north. The posted road period generally ends between April 25–May 1 in the south and May 1–14 in the north. However conditions in the state can vary considerably from north to south, and even from road to road in the same county. Unusually warm winters also affect road posting dates. Local knowledge of typical thaw periods is extremely helpful. Since a uniform system of spring weight restrictions is more understandable and enforceable, it is vital to coordinate with the Wisconsin DOT, the county, and adjoining road agencies. Also, when weight limits are not uniform or when some communities post limits and others don’t, vulnerable unposted roads may be damaged by truck traffic taking alternate routes. Local officials should time their road postings to coincide with the spring weight restrictions that WisDOT posts on the state highway system. The county highway department, WisDOT district maintenance office, and the WisDOT central maintenance office can tell you when they will begin. 4 Feb 15 Mar 1 Mar 15 Apr 1 Apr 15 May 15 Jun 1 May 1 1966 1970 1974 1978 1982 1986 1990 1994 1998 2002 Ending dates of weight restriction Starting dates of weight restriction Wisconsin Spring Weight Limits Season on Class II Road Sections Load Increase in reduction pavement life 20% 62% 30% 78% 40% 88% 50% 90% Page 11 of 19 To decide on a posting date, WisDOT uses informa- tion from frost tubes buried in pavements around the state. A liquid in the tubes changes color when it freezes. District maintenance staff check the tubes periodically to determine frost depth and location. There are also about 60 automatic pavement and weather monitoring stations in place around the state. By watching reports from these stations on pavement surface temperatures and at 18 inches below the surface, county and state highway staffs can better predict when spring thawing is underway. For local roads, you generally must use judgment and experience. However, a Thawing Index (TI)—calculated like heating degree days used by winter fuel suppliers— can help you predict when to begin restrictions. Figuring thawing degree days involves recording daily high and low air temperatures in your community and making a simple calculation. For weaker or problem pavements you may want to record daily highs and lows at the site. Studies also show that the Thawing Index is more reli- able for fine-grained soils than coarse-grained ones. Begin using the Thawing Index when the average daily temperature rises above 29° F—chosen as a reference temperature because tests show that an asphalt pavement surface is 32° F when air temperature is about 29° F. For midwinter thaws, use 31° F as the reference temperature for the Thawing Index because of lower sun angle and increased cloud cover in midwinter. You can use high and low temperature predictions from a five-day advance weather forecast to project when load restrictions must take effect. This will allow you to prepare the public and alert local heavy haulers. Pavement thickness determines how many thawing degree days are needed for applying spring load restric- tions. The FHWA study GuidelinesTforTSpringTHighway UseTRestrictionshas established “should” and “must” Thawing Index levels for thick and thin pavements (see below). The “should” level estimates thaw to the bottom of the base course. The “must” level estimates thaw to about four inches below the bottom of the base course. When to remove restrictions In general, keep weight restrictions in place until soils are completely thawed and drained to normal moisture levels. The most accurate way to tell is by testing for 5 Usual southern thawing season: from March 1–8 to April 25–May 1 Usual northern thawing season: from March 12–18 to May 1–14 90 90 94 94 94 43 43 94 53 53 51 51 45 45 141 8 8 29 18 151 151 10 Prairie du Chien Madison Beloit Kenosha Milwaukee Portage Oshkosh La Crosse Manitowoc Appleton Green Bay Eagle River Wausau Marshfield Stevens Point Wisconsin Rapids Ashland Superior Rice Lake Hudson Eau ClaireOsseo Thawingrconditionsrcanrvaryrconsiderablyrfromrnorthrtorsouth. Thawing Index levels for posting load restrictions on asphalt Pavement structure Thawing Index “Should”rLevel “Must”rLevelr THINAsphalt 2” or less 10° F-days 40° F-days Base course 6” or less THICKAsphalt more than 2” 25° F-days 50° F-days Base course more than 6” Thawing Index Average Daily Temperature Reference Temperature = 4° F–days TI 33° F – 29° F MINUS EQUALS Compute Thawing Index (TI) 100 0 100 0 High Low Average Daily TemperaturePLUS DIVIDED BY TWO Compute average daily temperature 28° F ÷ 2 38° F + = 33° F 100 0 100 0 EQUALS Day 1: 33° F - 29° F = 4° F-days Day 2: 35° F - 29° F = 6° F-days 2-day TI total: 4 + 6 = 10° F-days 1) Determine the average daily temperature by adding the day’s high and low temperatures and dividing by 2. 2) Subtract the reference temperature (29° F for spring thawing or 31° F for midwinter thaws) from the Daily Average Temperature. The remainder is the TI for that day. CalculatingrtherThawingrIndex Sample calculation of Thawing Index for two days: Page 12 of 19 deflection. However, combining judgement and experi- ence with an estimate based on the Thawing Index is very economical and will suffice in many cases. To make this estimate you must know the Winter Freezing Index. The Freezing Index is calculated the same way as the Thawing Index, using 32° F as the reference temperature. Beginning when the average daily temperature has been below 32° F for several days, calculate daily average temperatures. (Add the high and the low for the day and divide by 2.) Subtract the average daily temperature from 32° F and record the result. Keep a running total until spring thawing begins. This total is the winter’s freezing index in your area. High and low temperatures reported in the local media may also work well enough for this purpose. To calculate the total number of thawing degree days until the thaw is complete, multiply the Winter Freezing Index by 0.3. For example, for a Winter Freezing Index of 1375° F-days, the Thawing Index would be 412° F-days: 0.3rxr1375r=r412 Implementing local weight limits Authority To institute a permanent weight limit on a road, the local elected board or council should pass an appropriate ordinance and post the necessary signs. For a temporary restriction like spring load limits, the “authority in charge of maintenance” can impose the limits under Section 349.16 of theWisconsinTStatutes.T It may not be clear who is the “authority in charge of maintenance.” It is best for the local board or council, at a regularly scheduled meeting, to specifically identify a person or position to have that authority. For county trunk highways, the highway commissioner is commonly chosen. Towns, villages or cities should designate their highway superintendent, road foreman, street superin- tendent, or similarly titled officer. The board or council should also give this person or position authority to issue special weight permits. The local authority can impose weight limits on a highway or bridge that they believe will be damaged because of roadbed weakness or other special conditions. Signs must be posted to give notice of the restrictions, and these signs must conform to the current ManualTonTUniformTTrafficTControlTDevicesand the WisconsinTSupplementto that manual. For bridges there must be an advance warning sign at the nearest intersection. Limits become enforceable as soon as signs are in place. It can be complicated to analyze the capacities of individual pavements and bridges. Local authorities may use their judgement and knowledge of existing pavement conditions or may hire a consultant to conduct engineer- ing analyses. Limits based on actual testing will stand up to potential litigation better than those based on experience alone. Legal authority for establishing weight limits is found in Chapters 348 and 349 of the Wisconsin State Statutes. Chapter 348 establishes restrictions on the size, weight and loading of vehicles. Section 348.15 establishes specific truck weight limitations and exemptions. Sections 348.25, 348.26 and 348.27 outline the provisions for permits for vehicles of excessive size and weight. Such permits are generally issued by the state Department of Transportation for state highways. Local officials also have authority to issue credentials for their road systems under Section 348.26(2). Chapter 349 gives state and local agencies authority to regulate movement of heavy vehicles. Section 349.15 provides the authority to establish Class B highways on local roads. Section 349.16 gives the authority for local officials to impose special or seasonal weight limitations. Section 349.17 is the authority for cities, villages, and towns to establish designated truck routes. Exemptionsrandrenforcementr State statutes have many provisions permitting overloads for specific commodities such as milk and logs. As a result, some people believe that this special treatment applies to local roads with load restrictions. This is not the case. In fact, local weight limits override all special permits in the statutes. Local officials maymake exceptions, but are not required to. Once load limits are posted, numerous requests for exceptions are likely. Local agencies may make excep- tions, but it is important to be consistent and reasonable. Overusing exceptions weakens the effectiveness of load limit programs. 6 Page 13 of 19 PublicTagencyTvehiclesTareTnotTexemptTfromTweight andTsizeTrestrictions.All statutory restrictions and locally adopted weight restrictions apply uniformly to public vehicles as well as private trucks. To implement your authority to issue exemptions under Section 349.16(3) it is best to put the exemptions in writing. For commodities that will be exempted either seasonally or permanently, make a good faith effort to publish these rules. If, as a local official, you intend to exempt some commodities, you can still restrict their movement by specifying how often each day they may travel on a road. You may also require that they travel at specific times during the day, such as before 7:30 am when overnight temperatures may have temporarily strengthened the road. Like the basic exemptions, these restrictions should be in writing and publicized. Before posting roads, local agencies should plan how to enforce the limits. Law enforcement officers can order an apparent violator off the highway and issue citations. Repeat violators must pay higher amounts, and the amount to be paid increases with the amount of weight over the limit. State Patrol officers and county deputies are author- ized to enforce weight limits. The State Patrol offers annual training sessions on enforcing truck sizes and weights for local law enforcement officials. Scales used to enforce weight laws must be certified accurate. Haulers have another considerable incentive to comply. Under Section 86.02 of the Statutes, a party which has caused damage to the highway is liable for triple the cost to repair the damages. These are collected through civil court. Speed enforcement is also important because damage is increased at high speed. Permitsr Haulers with loads over the weight and size limitations can request permits for travel on state trunk highways from the Wisconsin DOT. Permits can be for a single trip or multiple trips and are issued at the WisDOT central office in Madison. Except for vehicles authorized in the Statutes to have excess axle weights (Sections 348.15(3) (bg, br, & bv), trucks which intend to also use local road systems must obtain permission from the local maintenance authority. Local agencies should establish permit procedures and designate a person with authority to issue them. Assigning this to the same person who establishes weight limits is reasonable and convenient. However, if a different person is issuing permits—the town clerk, for example—it is a good idea to coordinate with the local authority which establishes the limits. Local permit forms may be individualized, but many local officials have found it useful to copy WisDOT forms. Single trip permits authorize an overweight or over- sized vehicle to make one trip over a designated route. The local authority should carefully select roads and bridges that can adequately handle the excess load. Determining these permitted routes can be complex and may require help from an engineering consultant. When the state puts roads into “thaw status,” it reduces maximum weights for single trip permits. It also suspends the authority for moving overweight loads that are divisible (like garbage, logs, agricultural products), and declares certain vulnerable state highways as Class II roadways which limits the maximum weight during spring thaw to a GVW of 80,000. Class II roadways may also be temporarily posted for even lower weight limits. Signingrforrweightrrestrictionsr Weight restriction signs are regulatory and should be white with black lettering to conform with the federal ManualTonTUniformTTrafficTControlTDevicesTdMUTCDe and the WisconsinTSupplement. Uniform signing improves coopera- tion and makes enforcement easier. All weight limit signs must say: “by order of” the local agency. Class B high- way signs should be installed at intersections with other highways. Bridge weight restriction signs must follow instructions from WisDOT. These signs must include the gross weight and maximum limits for axle loads. Signs should be posted at the bridge and also far enough in advance that trucks can detour around the limited structure. Permanent special weight signs must be permanently installed and designate the maximum gross weight. Temporary weight limits such as spring load restrictions should also be on standard signs that are reflectorized and that meet the standards of the MUTCD. Hand painted and faded signs are not appropriate. 7 BY ORDER OF TOWN OF FAVREVILLE BY ORDER OF TOWN OF FAVREVILLE BY ORDER OF PACKER COUNTY BY ORDER OF PACKER COUNTY Page 14 of 19 BulletinTNo.TwTrevisedTNovemberTommpT©TCopyrightTWisconsinTTransportationTInformationTCenter.T WisconsinrTransportationrBulletinrisTaTseriesTofTfactTsheetsTprovidingTinformationTtoTlocalTtown,TmunicipalTandTcountyTofficialsTonTstreetTandThighwayTdesign,Tconstruction,T maintenance,TandTmanagement.TTheseTfactTsheetsTareTproducedTandTdistributedTbyTtheTWisconsinTTransportationTInformationTCenter,TaTprojectTofTtheTUniversityTofTWisconsinj Madison,TDepartmentTofTEngineeringTProfessionalTDevelopment,TfundedTasTaTLocalTTechnicalTAssistanceTCenterTbyTtheTFederalTHighwayTAdministration,TWisconsinTDepartmentT ofTTransportation,TandTUWjExtension.TUWjMadisonTprovidesTequalTopportunitiesTinTemploymentTandTprogramming,TincludingTTitleTIXTrequirements. CopiesTareTavailableTfreeTwhileTsuppliesTlastTfromTtheTTransportationTInformationTCenter,TqpoTNorthTLakeTStreet,TMadison,TWITrpvmu.T PhoneyTwmm/qqojqunrzTejmailyTtic@epd.engr.wisc.eduzTURLyThttpy//tic.engr.wisc.edu 8 Communication Effective communication with the public, your own agency, and affected haulers is essential. Alert the local media when weight restrictions are imminent. Remind drivers of public works trucks that weight restrictions apply to them too. Contact industries which make local deliveries or supply local services and tell them what the limits are and when limits will begin. Consult with local haulers about ways to protect par- ticularly vulnerable roads. For example, milk haulers could alter the order of pick up to lessen the weight at a bad site, or septic pumpers may limit how full their tanks are when traveling problem roads to service customers. Large construction projects that require hauling heavy construction materials need special coordination in advance. Local officials and contractors should plan together well before the limits are imposed. They can agree on specific hauling routes using roads that are both strong enough and reasonably efficient. Advance agreements with contractors and other heavy haulers can be very effective. Informal agreements or formal contracts assign responsibility to these haulers for repairing damage along their routes. Some agencies require bonds or escrow accounts in advance to ensure compliance. Inspecting haul routes ahead of time is important in enforcing these agreements. Photographing or video taping is also helpful in documenting existing condition. These techniques establish pavement condi- tions before spring thaw begins. The alternative to advance agreements—establishing very restrictive weight limits after bids are in or construc- tion is underway—can be very disruptive and costly, and may result in litigation. Both contractors and local agen- cies are responsible for this advance coordination. Summary Protecting local roads from damage by heavy vehicles is the responsibility of local authorities. WisconsinTStatutes provide adequate authority to exercise this control. In establishing weight restrictions, local authorities must use judgment and common sense to balance the need for protecting roads with maintaining commerce and an efficient transportation system. Close coordination with Wisconsin DOT and adjoining local agencies is essential to an effective program. Also, set a good example with your own agency. Be sure that all publicly-owned equipment observes the weight restrictions. Resources GuidelinesrforrSpringrHighwayrUserRestrictions, Federal Highway Administration, Report No. FHWA- TS-87-209, Turner-Fairbank Highway Research Center, 6300 Georgetown Pike, McLean, VA 22101-2296. And related videotapes. StaterHighwayrMaintenancerManual,rGuideline 30.06, January 1, 1993, Wisconsin Department of Transpor- tation, State Maintenance Engineer for Highways, PO Box 7916, Madison, WI 53707-7916. HowrVehiclerLoadsrAffectrPavementrPerformance, Wisconsin Transportation Information Bulletin, No. 2, Wisconsin Transportation Information Center–LTAP, 432 N. Lake St., Madison, WI 53706. Other references StudyrEffectsrofrOff-RoadrEquipmentrTiresronrFlexible andrGranularrPavements.An Executive Summary of the South Dakota Department of Transportation describes damage to test pavements. The report is available for download at: http://www.state.sd.us/Applications/HR19 ResearchProjects/oneproject_search.asp?projectnbr= SD1999-15 (The 131 page report is a 4.4 MB pdf file.) FrostrHeave:rWhatrcausesritrandrhowrwercanrinterfere withrit,Special Bulletin #19, November 1995. Written by Dr. Rich Reid, Asst. Prof. of Civil Engineering, South Dakota State University, for South Dakota Transportation Technology Transfer Service. AGuidertorSpringrHighwayrUserRestrictions:rWhenr torApply,rHowrLongrtorApply,randrWhenrtorRemove. TheTBridgeTFactTSheet,Spring 1994, Michigan Local Technical Assistance Program, Houghton, Michigan. PostingrandrBondingrLocalrRoads:rASolutionrto DamagesrCausedrbyrHeavyrHaulers,LTAP Technical Information Sheet #57, January 1994, by Alan L. Gesford, LTAP Engineer, Pennsylvania Local Roads Program, Penn State Harrisburg, 777 West Harrisburg Pike, Middletown, PA 17057-4898. WalshrCounty’srLoadrLimitrEnforcementrProgram,by Harvey Melstad, in TheTCenterTLine,TFall 1990, North Dakota State University. LegalrOpinionsby Attorney J.R. Habeck, in the news- letter of the Wisconsin Towns Association. Page 15 of 19 PORTAGE COUNTY MEETING MINUTES AD HOC ADVISORY COMMITTEE ON INDUSTRIAL LIVESTOCK OPERATIONS PORTAGE COUNTY ANNEX CONFERENCE ROOMS 1 & 2 1462 STRONGS AVENUE STEVENS POINT, WI 54481 Wednesday, October 29, 2025 7:00 PM REMOTE ATTENDANCE & COMMENT To attend this meeting by telephone : dial 1-872-242-7813, after dialing the number you will then be asked to enter in a meeting number. Use the following meeting number: 337 011 568, then press # To attend this meeting by video: Join the meeting now Page 1 of 2 CALL TO ORDER The Ad Hoc Advisory Committee on Industrial Livestock Operations meeting was called to order at 7:00pm. Members Present: Amberle Schwartz, Janell Wehr, Ken Feltz, Tyler Bulgrin, Mike Pagel, Lynn Markham, Christine Mechenich Staff Attending: Tracy Arnold, Shawn O'Connell, Andrew Senderhauf, Tim Reed, Camryn Brewbaker, Tyler Kunze CORRESPONDENCE No Report. PRESENTATIONS 1. Victoria Ziegler, Department of Natural Resources, Program Coordinator on Concentrated Animal Feeding Operations (CAFO) — CAFO Overview Victoria Ziegler presented on how the Department of Natural Resources regulates CAFOs. 2. Tim Jackson, Agricultural Land Use, Planning and Ordinance Specialist and Jenn Chakravorty, Ordinance Specialist with the Department of Agriculture, Trade and Consumer Protection — Operational Ordinance Standards under Wis. Stats. Chapters 92 and 93. Tim Jackson presented on the Department of Agriculture, Trade, and Consumer Protection Operational Ordinance Standards under Wis. Stats. Chapter 92 and 93. REPORTS 3. Special Meeting Attendance Reports (Portage County Ordinance 3.1.47 & 3.1.48) No Report. PUBLIC NOTICE Members of the public who wish to address the Committee on specific agenda items must register their request at this time, with such comments subject to the public comment ordinance and the reasonable control of the Committee Chair as set forth in Robert’s Rules of Order. APPROVAL OF MINUTES 4. Approval of October 15th, 2025 Meeting Minutes A motion was made by Mike Pagel, seconded by Tyler Bulgrin, to Approve minutes. Motion to Approve minutes carried by voice vote, with no negative votes. DISCUSSION/POSSIBLE ACTION 5. Discussion/Possible Action Re: Waste management recommendations as they relate to proposed industrial livestock operations ordinance Page 16 of 19 Ad Hoc Advisory Committee on Industrial Livestock Operations Meeting Minutes October 29, 2025 Page 2 of 2 The committee discussed waste management recommendations. 6. Discussion/Possible Action Re: Environmental impact recommendations as they relate to proposed industrial livestock operations ordinance Line item moved to next meeting date of November 5th, 2025. 7. Discussion/Possible Action: Review of Schedule of Future Agenda and Committee Recommendations The committee reviewed schedule of future agenda and committee recommendations. NEXT MEETING DATE November 5th, 2025 There will be a quorum of committee members on Monday, November 3rd for a Farm Tour. Members will meet in the parking lot of the Portage County Annex Building and carpool to Miltrium Farm in Marathon County. The meeting will be called to order at the Annex Building and adjourned at the farm. Separate cars will be driven as no quorum is allowed in one vehicle at a time. The next committee meeting will take place in the Portage County Annex Building, Conference Rooms 1 & 2, on November 5th, 2025 at 7:00pm. ADJOURNMENT Meeting adjourned at 10:08pm. Page 17 of 19 Schedule of Future Agenda and Committee Recommendations LAST UPDATED 10/29/25 Meeting Date Topics Other Info Fire/Emergency Management • Documentation and map of facilities on site • Determine firefighting water needs • Fire readiness/training • Pre incident fire safety plan required – once a year walkthrough, onsite and employee housing, 360 access to facilities & 60-foot clearance for fire lanes, fire dept has access to all gates/buildings (Knox box) • Fire exits every 15,000 sq ft • Map of site showing housing, water sources and pumping capacity, and where fuel and other chemicals are stored Added October 29th meeting date Waste Management/Nutrient Management Triggers – total animal units • If existing farm is over 1,000 animal units, ordinance is triggered once 500+ animal units are added (proposed but not approved at 10.15.25 meeting) • Calculate mass balance nitrogen as an educational tool, make sure it is simple & possibility in a spreadsheet • County staff has the discretion to request, review & verify landowner lease agreements/manure land application agreements LWCD & UW Extension Presentations Farm Tour- Monday, Nov 3rd @8am Environmental impacts DATCP & DNR Presentations Nov 5th Roads, financial security Nathan Check Nov 19th Public health, population & depopulation, biosecurity State vet & Po Co Health Dept Dec 3rd Page 18 of 19 Page 19 of 19

Source: Portage County website. First collected Nov 13, 2026.